• Journal of Welding and Joining
• /
• v.3 no.1
• /
• pp.11-21
• /
• 1985

The line heating is a thermoplastic working technique which is used in bending work of steel plate and in correcting the distortion of welded structure. This method is considerably effective when the water-cooling is followed. In this study, an investigation was accomplished to find the effects on the change of material properties when the line heating was applied on the high tensile steel plate of 50kg/mm^2$ grade. Some steel plates were heated to various temperatures and then cooled with water or in the air. In this study, the author measured the angular distortion continuously during line heating to find out the relation between the bending efficiency and heating or water-cooling temperature. Furthermore, its material properties were examined by the V-notch Charpy impact test, the microscope observation and the Vickers hardness test. As results, the followings were clarified. (1) The amount of angular distortion increases as the heating temperature or the water-cooling temperature rises. (2) When the steel plate is heated between 700.deg. C and 900.deg. C, and then is water-cooled over 700.deg. C, some brittle structure is observed. But if the temperature of water-cooling is below 700.deg. C, no brittle one is found. (3) When the steel plate is heated over 800.deg. C and is cooled in the air, there is no unfavrable effect.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.167-168
• /
• 2006

High quality 3D-heterostructures were constructed by selective area (SA) molecular beam epitaxy (MBE) using a specially patterned GaAs (001) substrate. MBE growth parameters such as substrate temperature, V/III ratio, growth ratio, group V sources ($As_2$, $As_4$) were varied to calibrate the selective area growth conditions. Scanning micro-photoluminescence ($\mu$-PL) measurements and following analysis revealed that the gradually (adiabatically) coupled 2DEG-1D-1DEG field effect transistor (FET) system was realized. This 3D-heterostructure is very promising for the realization of the meso-scopic electronic devices and circuits since it makes it possible to form direct ohmic contact to the (quasi) 1DEG.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.1
• /
• pp.74-81
• /
• 1987

The orthogonal cutting method of the nodular graphite cast iron in the lathe turning, whose structure were formulated under two kinds of annealing conditions, has been experimentally studied and the results investigated. The various characteristics of machinabilities of the nodular cast iron, depending upon its structure, have been obtained from the results as follows. (1) As depth of cut increases, the shearing strain decreases and tend gradually to increase with increase of ferrite matrix. (2) As depth of cut increases, the shearing stress slightly decreases for P$_{1}$, but it tends to increase for both of P$_{2}$ and P$_{3}$ under the same condition. The annealing effect in the process of light cutting was found to be greater than heavy cutting. (3) The cutting energy slightly decreases with the increassing of the depth of cut, and the effect of decreasing the cutting energy by the annealing is higer the light cutting than the heavy cutting. (4) The cutting equations as follow. P$_{1}$ : 2.phi.+1.58(.betha.-alpha.)=92 deg. P$_{2}$ : 2.phi.+1.40(.betha.-alpha.)=84 deg. P$_{3}$ : 2.phi.+1.37(.betha.-alpha.)=82 deg. (5) The machining constants for P$_{1}$, P$_{2}$ and P$_{3}$ which are the test-pieces in this study and classified according to the containing quantity of ferrite matrix given respectively in 78deg., 70 deg., and 68 deg. From these it can be known that the machining constants slightly decreases with increasing of the quantity of ferrite matrix contained in the nodular graphite cast iron.

• Journal of Advanced Marine Engineering and Technology
• /
• v.8 no.2
• /
• pp.81-87
• /
• 1984

The effect of heat treatment and mechanical stress on the dielectic strength of epoxy resin film is studied. The film with 30-210 .mu.m thickness are casted at room temperature for 8 hours and post cured at the range of temperature 60-180 .deg. C, and the heat setting time are two kind, ie, 2 and 10 hours. The samples are made with Stycast 1266 that the primary compound is diglycidyl ether of bisphenol A, and the hardner is denaturated polyamines. Under no mechanical stresses, the maximum dielectric strength of the sample is obtained for the sample heat treated for 2 hours at 150 .deg. C. However, the best dielectric strength characteristics under compressive stress is obtained for the sample heat treated at 90 .deg. C and 120 .deg. C. The dielectric strength of the sample are also affected significantly by the cooling velocity of the sample after post heat setting at given temperature.

• Journal of Ocean Engineering and Technology
• /
• v.1 no.2
• /
• pp.101-112
• /
• 1987

Fracture toughness characterization in the transition region is examined for heat-treated and ionnitrided Ni-Cr-Mo steel. After heat treatment for the specimens of Ni-Cr-Mo steel, organizations of specimens-specimens which are heat-treated and ion-nitrided for 4 hours at 500 .deg. C and 5 torr in 25%N/dub 2/-75%H/sub 2/mixed gas-, hardness variety, and X-ray diffraction pattern of the ion-nitriding compound layer are observed. Fracture toughenss test of unloading compliance method were conducted over the regions from room trmperature to -70.deg. C. The compound layer was consisted of r'=Fe/sub 4/N phase and ion-nitrided layer's depth was 200mm from surface. The transition regions of heat-treated and ion-nitrided specimens were about -30.deg. C and -50.deg. C, respectively. The transition region of ion-nitrided specimens is estimated less than that of heat-treated one, and this is the effect of ion-nitriding.

• Electrical & Electronic Materials
• /
• v.9 no.10
• /
• pp.1013-1018
• /
• 1996

The annealing effects of Au/Te/Au/n-GaAs structure was investigated by using x-ray diffraction, scanning electron microscope, the specific contact resistance and I-V measurement. Increasing the annealing temperature, the intensity of Au-Ga peak by X-ray diffraction was increased. The Ga$\_$2/Te$\_$3/peak got evident for the samples annealed at 400.deg. C and GaAs peak by recrystallization appeared for the samples annealed at 500.deg. C. The variation from the schottky to low resistance contact was confirmed by I-V curve. The lowest value of the specific contact resistance of the samples annealed at 500.deg. C was 3.8*10$\^$-5/.ohm.-cm$\^$2/ but the value increased above 600.deg. C.

• Journal of the Korean Institute of Gas
• /
• v.20 no.2
• /
• pp.16-22
• /
• 2016

Auto ignition characteristic is an important factor for handling combustible substance and fire prevention. This research studied about auto ignition characteristic and activation energy of Ethylene Glycol (EG) and Diethylene Glycol (DEG) by using ASTM D2155 type ignition temperature measuring apparatus. As the auto ignition temperatures, it was possible to get $434^{\circ}C$ for EG within sample amount range of $75{\sim}160{\mu}l$ and $387^{\circ}C$ for DEG within sample amount range of $130{\sim}150{\mu}l$. Also, it was possible to get $579^{\circ}C$ and $569^{\circ}C$ as instantaneous ignition temperatures with sample amount of $140{\mu}l$ for EG and DEG respectively. By using least square method from Semenov equation on measured ignition temperature and ignition delay time from this study, it was possible to calculate activation energy of EG as 25.41 Kcal/mol and DEG as 14.07 Kcal/mol. Therefore, it was possible to claim that DEG has more risk of auto ignition since the auto ignition temperature, instantaneous ignition temperature and activation energy of DEG is lower than EG.

• Electrical & Electronic Materials
• /
• v.8 no.3
• /
• pp.267-271
• /
• 1995

The electrical properties of (S $r_{0.50}$P $b_{0.25}$B $a_{0.25}$)Ti $O_{3}$ ceramics were studied. Specimens were prepared by the conventional mixed oxide method, and fired between 1300[.deg. C] - 1375[.deg. C], for 2[hr.]. The electrical and structural preperties of specimens were investigated with sintering temperature. Increasing the sintering temperature from 1300[.deg. C] to 1375[.deg. C], average grain size was increased from 2.61[.mu.m] to 4.53[.mu.m]. (S $r_{0.50}$P $b_{0.25}$B $a_{0.25}$)Ti $O_{3}$ specimen sintered at 1350[.deg. C] for two hours showed good dielectric constant(2147) and dielectric loss(1.7[%]) properties at 1[khz]. Sintered density and breakdown field strength were the highest value of 5.75[g/c $m^{3}$], 20[kV/cm], respectively. Dielectric properties with applied voltage were independent of the sintering temperature.temperature.

• Electrical & Electronic Materials
• /
• v.4 no.3
• /
• pp.249-258
• /
• 1991

He-Ne레이저(.lambda.=0.6328[.mu.m])를 광원으로 사용하는 y-cut LiNbO$_{3}$기판의 광 도파로 형성 과정을 빔 전송방식 메카니즘을 이용하여 광 도파로에서 광파의 전계 변화 및 전계 분포에 대하여 시뮬레이션 하였다. 그리고 Xl(55[.mu.m])* Zl(5000[.mu.m])인 LiNbO$_{3}$기판의 광 도파로 폭을 4[.mu.m], 버퍼층을 0.02[.mu.m]로 하였을때 도파로 층의 깊이가 0.2[.mu.m]인 지점에서 인가전압에 대한 x방향의 전계(E$_{x}$)와 y방향의 전계(E$_{y}$ )분포를 관찰하였다. 또한 단일 도파로의 파라미터 조건을 적용하여 X-스위치를 구성하였을때 전계를 인가하지 않은 상태에서 굴절율 변화(dn) 0.002, 도파로 폭(w) 3[.mu.m]로 하여 도파로의 교차각(.alpha.)을 0.4.deg.~0.6.deg.로 변화시킨 경우, .alpha.=0.5.deg.와 0.6.deg.일 때는 광빔이 bar측으로 출력되었고 .alpha.=0.4에서는 광빔이 cross측으로 출력 됨을 확인하였다. 따라서 위에서 확인된 도파로의 교차각 .alpha.=0.4.deg.인 경우, 전극간격(gap)이 2[.mu.m]인 조건에서 스위칭 전압을 인가하였을 때 25[V]에서 전기광학 효과에 의하여 광빔이 cross측에서 bar측으로 변조됨을 확인함으로써 X-스위치 광변조기의 기본적인 설계조건을 구현하였다.

• Electrical & Electronic Materials
• /
• v.3 no.4
• /
• pp.315-324
• /
• 1990

저저항(DuPont 1721, 100.OMEGA./sq.)과 고저항(1741, 10K.OMEGA./sq.)의 두 Ru계 후막저항체를 여러 조건에서 소결하여 소결막의 복소임피던스 특성과 임피던스의 주파수의존성을 1KHz-13MHz의 주파수 범위에서 조사하였다. 저저항 1721계의 경우 600.deg.C이상에서 소결한 모든 시편이 거의 저항성분(R)만으로 구성된 등가회로에 해당되는 복소임피던스 거동을 보였으며 임피던스에 미치는 주파수 의존성은 크게 나타나지 않았는데 5KHz까지는 주파수에 따라 변화가 없다가 그 이상의 주파수에서 주파수 증가에 따라 약간씩 증가하였다. 고저항 1741 후막저항체의 경우는 소결조건에 따라 복소임피던스 거동과 임피던스에 미치는 주파수 의존성이 달리 나타났다. 600.deg.C에서는 용량(C) 성분만으로 구성된 등가회로에 해당하는 복소임피던스 거동을 얻었고 주파수 증가에 따라 임피던스가 직선적으로 감소하였으며 700.deg.C이상 900.deg.C까지는 저항(R)과 용량(C)이 병렬로 연결되는 형태의 등가회로에 해당하는 복소임피던스 거동을 얻었고 이때의 임피던스의 주파수 의존성은 저주파수 영역에서는 임피던스가 주파수에 변함없이 일정하다가 5KHz이상의 주파수에서는 주파수 증가에 따라 임피던스가 직선적으로 감소하였다. 1000.deg.C반응에서의 복소임피던스 거동은 RCL성분이 병렬로 연결된 형태의 등가회로에 해당되는 결과를 얻었으며 임피던스도 작아지고 주차수 의존성도 현저하지 않았다.