• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.2
• /
• pp.265-281
• /
• 2017

For shallow tunnel constructions, settlement of the ground surface is a main issue. Recent technical developments in shield TBM tunneling technique have enabled a decrease in such settlements based on tunneling with ground deformation controls. For this objective, the tail void grouting is a common practice. Generally surface settlements in a soil of low permeability occur during a tunnel construction but also during a long period after completion of the tunnel. The long-term settlements occur mainly due to consolidation around the tunnel. The consolidation process is caused and determined by the tail void grouting which leads to an excess pore water pressure in the vicinity of the tunnel. Because of this, the grouting pressure has a strong effect on the long-term settlements in the shield tunneling. In order to investigate this effect, a series of coupled hydro-mechanical 3D finite element simulations have been performed. The results show that an increase in grouting pressure reduces the short-term settlements, but in many cases, it doesn't lead to a reduction of the final settlements after the completion of consolidation. Thereby, the existence of a critical grouting pressure is identified, at which the minimal settlements are expected.

• Journal of the Korea Concrete Institute
• /
• v.17 no.4 s.88
• /
• pp.505-511
• /
• 2005

This experimental investigation was conducted to examine the seismic performance of reinforced concrete bridge columns. The columns were subjected to a constant axial load and a cyclic horizontal load-inducing reversed bending moment. The variables studied in this research were the volumetric ratios of transverse reinforcement (ps=0.96, 1.44 percent) and axial load ratios (P/Po=0.05, 0.1, 0.2) and concrete strengths (35, 60MPa). Test results showed that bridge columns with $44\%$ higher amounts of transverse reinforcement than that required by seismic provisions of ACI 318-02 showed ductile behavior. For bridge columns with axial load ratio(P/Po) less than 0.2, the ratio of $M_{max}\;over\;M_{ACI}$, nominal moment capacity predicted by ACI 318-02 provisions, was consistently greater than 1 with approximately a $20\%$ margin of safety.

• The Journal of Korean Academy of Prosthodontics
• /
• v.57 no.4
• /
• pp.321-327
• /
• 2019

Purpose: To evaluate an effect of additional firing process after sintering of monolithic zirconia crown on marginal and internal fit through three-dimensional analysis. Materials and methods: Ten monolithic zirconia crowns were fabricated using titanium abutment model. Monolithic zirconia crowns were designed, milled, and sintered as a control group, and additional firing with coloring was performed as a test group. Three dimensional analysis were performed by using triple-scan protocol, and cross-section analysis on mesio-distal and disto-lingual section was evaluated to measure marginal and internal fitness. Then, three-dimensional surface difference on between two groups was evaluated (${\alpha}=.05$). Results: There was statistically significant difference between the control group ($32.0{\pm}24.3{\mu}m$) and the test group ($17.0{\pm}10.8{\mu}m$) in the mesial axial wall (P < .02) and the control group ($60.2{\pm}24.3{\mu}m$) and the test group ($71.8{\pm}21.5{\mu}m$) in the distal axial wall (P < .01). There was no statistically significant difference at the remaining point. Conclusion: There was no statistical significance on the deviation of inner surface of crown according to firing number, and the results of both group were considered clinically acceptable.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.35 no.4
• /
• pp.243-248
• /
• 2022

Weight optimization was performed for a rotorcraft shaft system using one-dimensional Euler-Bernoulli beam elements. Torsion, shaft support stiffness such as bearings, flange mass are all considered. To guarantee structural dynamic stability, eigenvalue analysis was performed to avoid critical speed and tooth mesh excitation form the gearbox. The weight optimization was performed by adjusting the thickness and radius while the length of the shaft was fixed, and the optimization process was divided into two stages. In the first, the weight is optimized with the torsional strength constraint. In the second, the difference between the primary mode of shaft and the critical speed is maximized so that the primary mode of the shaft can avoid the critical speed while the constraint on the torsional strength of the shaft is satisfied according to the standard for shaft system stability (AMC P 706-201, 1974). The proposed method was verified by comparing the results of the optimal design using the given one-dimensional beam elements with the stress results of the 3D finite element and the actual manufactured shaft.

• Journal of Animal Science and Technology
• /
• v.45 no.5
• /
• pp.689-694
• /
• 2003

Weight records of Hanwoo cows from birth to 36 months of age collected in Daekwanryeong branch, National Livestock Research Institute(NLRI) were fitted to Gompertz, von Bertalanffy and Logistic functions. For the growth curve parameters fitted on individual records using Gompertz model, the mean estimates of mature weight(A), growth ratio(b) and growth rate(k) were 383.42 ${\pm}$ 97.29kg, 2.374 ${\pm}$ 0.340 and 0.0037 ${\pm}$ 0.0012, respectively, and mean estimates of body weight, age and daily gain rate at inflection were 141.05 ${\pm}$ 35.79kg, 255.63 ${\pm}$ 109.09 day and 0.500 ${\pm}$ 0.123kg, respectively. For von BertalanfTy model, the mean estimates of A, b and k were 410.47 ${\pm}$ 117.98kg, 0.575${\pm}$0.057 and 0.003 ${\pm}$ 0.001, and mean estimates of body weight, age and daily gain at inflection were 121.62 ${\pm}$ 34.94kg, 211.02 ${\pm}$ 105.53 and 0.504 ${\pm}$ O.l24kg. For Logistic model, the mean estimates of A, b and k were 347.64 ${\pm}$ 97.29kg, 6.73 ${\pm}$ 0.34 and 0.006 ${\pm}$ 0.0018, and mean estimates of body weight, age and daily gain at inflection were 173.82 ${\pm}$ 37.25kg, 324.47 ${\pm}$ 126.85 and 0.508 ${\pm}$ 0.131kg. Coefficients of variation for the A, b and k parameter estimates were 25.3%, 14.3% and 32.4%, respectively, for Gompertz model, 28.70/0, 9.9% and 33.3% for von Bertalanffy model, and 27.9°/0, 5.0% and 30.0% for Logistic model.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.4
• /
• pp.318-325
• /
• 2011

Pitch pine (Pinus rigida Miller) retaining walls using Steel bar, of which the constructability and strength performance are good at the construction site, were manufactured and their strength properties were evaluated. The wooden retaining wall using Steel bar was piled into four stories stretcher and three stories header, which is 770 mm high, 2,890 mm length and 782 mm width. Retaining wall was made by inserting stretchers into Steel bar after making 18 mm diameter of holes at top and bottom stretcher, and then stacking other stretchers and headers which have a slit of 66 mm depth and 18 mm width. The strength properties of retaining walls were investigated by horizontal loading test, and the deformation of structure by image processing (AlCON 3D OPA-PRO system). Joint (Type-A) made with a single long stretcher and two headers, and joint (Type-B) made with two short stretchers connected with half lap joint and two headers were in the retaining wall using Steel bar. The compressive shear strength of joint was tested. Three replicates were used in each test. In horizontal loading test the strength was 1.6 times stronger in wooden retaining wall using Steel bar than in wooden retaining wall using square timber. The timber and joints were not fractured in the test. When testing compressive shear strength, the maximum load of type-A and Type-B was 130.13 kN and 130.6 kN, respectively. Constructability and strength were better in the wooden retaining wall using Steel bar than in wooden retaining wall using square timber.

• Korean journal of applied entomology
• /
• v.46 no.2
• /
• pp.213-219
• /
• 2007

The development of Schizaphis graminum (Rondani) was studied at various constant temperatures ranging from 15 to $32.5^{\circ}C$, with $65{\pm}5%$ RH, and a photoperiod of 16L:8D. Mortality of the $1_{st}-2_{nd}\;and\;the\;3_{rd}-4_{th}$ stage nymphs were similar at most temperature ranges while at high temperature of $32.5^{\circ}C$, more $3_{rd}-4_{th}$ stage individuals died. The total developmental time ranged from 13.8 days at $15^{\circ}C$ to 4.9 days at $30.0^{\circ}C$ suggesting that the higher the temperature, the faster the development. However, at higher end temperature of $32.5^{\circ}C$ the development took 6.4 days. The lower developmental threshold temperature and effective accumulative temperatures for the total immature stage were $6.8^{\circ}C$ and 105.9 day-degrees, respectively and the nonlinear shape of temperature related development was well described by the modified Sharpe and DeMichele model. The normalized cumulative frequency distributions of developmental period for each life stage were fitted to the three-parameter Weibull function. The attendance of shortened developmental times was apparent with $1_{st}-2_{nd}\;nymph,\;3_{rd}-4_{th}$ nymph, and total nymph stages in descending order. The coefficient of determination $r^2$ ranged between 0.80 and 0.87.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.43 no.11
• /
• pp.1648-1657
• /
• 2014

In this study, the hepatic lipid-lowering effects and related mechanism of action of sujeonggwa were examined in hypercholesterolemia-induced apoprotein E knockout (apo E ko) mice. Sujeonggwa drink was prepared with cinnamon, ginger, and sugar by modifying the traditional recipe of sujeonggwa. Sugar was partially substituted with either stevia or short chain fructooligosaccharide (scFOS) in order to reduce the calorie content of sujeonggwa, which was measured by descriptive analysis. Apo E ko mice (n=42) were induced to have hypercholesterolemia (plasma total cholesterol concentration >1,000 mg/dL) by administration of a high cholesterol diet for 4 weeks, followed by division into six groups. Experimental groups were orally administered water as a vehicle (normal group), sugar solution (control group), commercially available 'V' sujeonggwa drink (positive control group), or three different types of sujeonggwa drinks (S-sugar, S-stevia, and S-scFOS group) for 6 weeks while high cholesterol diet was provided to all animals. Compared to the control group, concentrations of hepatic triglycerides, total cholesterol, thiobarbituric acid reactive substances, and reactive oxygen species in S-sugar, S-stevia, S-scFOS were significantly reduced (P<0.05), indicating that sujeonggwa had inhibitory effects on hepatic lipid accumulation. Protein expression levels of fatty acid synthase (FAS) and its transcription factor, sterol regulatory element-binding protein (SREBP)-1 responsible for triglyceride synthesis, as well as 3-hydroxy-3-methylglutaryl-CoA reductase (HMGCR) and its transcription factor, SREBP-2 responsible for cholesterol synthesis, were also reduced in S-sugar, S-stevia, and S-scFOS groups (P<0.05). These benefits of sujeonggwa were even greater in S-stevia and S-scFOS compared to S-sugar. The beneficial effects of S-stevia on regulation of hepatic lipid metabolism were slightly greater than those of S-scFOS although the differences were not significant. In conclusion, sujeonggwa drinks, especially functional sujeonggwa drinks in which sugar was partially substituted with stevia or scFOS, inhibited hepatic lipid accumulation via suppressing FAS and HMGCR protein expression through down-regulation of SREBP-1 and 2.

• KSBB Journal
• /
• v.23 no.3
• /
• pp.231-238
• /
• 2008

The second family member of tissue inhibitors of matrix metalloproteinases, TIMP-2, is a 21kDa protein which inhibits matrix metalloproteinases 2 (MMP-2). Expression of mammalian proteins in E. coli often forms inclusion bodies that are made up of mis-folded or insoluble protein aggregates. The requirement for the formation of 6 disulfide bonds in the process of the TIMP-2 folding is likely to be incompatible with the reducing environment of E. coli. However, this incompatibility can be often overcome by introducing a mutagenesis that could lead to enhancement of the protein solubility. In this reason, we have attempted to express the soluble TIMP-2 in E. coli by applying a modified staggered extension process (StEP), one of the in vitro PCR-based recombinant mutagenesis methods, and error-prone PCR. C-terminally located CAT fusion protein with respect to mutated TIMP-2 proteins enables us to differentiate the soluble TIMP-2 from the insoluble in E. coli by virtue of chloramphenicol resistance. According to this scheme, E. coli harboring properly-folded CAT fused to TIMP-2 protein was selected, and some of the resulting colonies exhibited an enhanced, soluble expression of TIMP-2 compared to the wild type, implying (i) the StEP technique is successfully employed to enhance the proper folding thereby increasing the solubility of TIMP-2, and (ii) the CAT dependent screening may be a simple and effective method to differentiate the soluble protein expression in E. coli.

• Resources Recycling
• /
• v.2 no.2
• /
• pp.27-38
• /
• 1993

In this study, we investigated the grinding and sedimentation(elutriation) process of the dusts for the effective separation of high purity iron and iron oxides. For characterization of the dust, particle size distribution and chemical composition, were examined. The results obtained in this study may be summarized as follows : 1. The converter CF(clarifier) dust of the Pohang 1st, 2nd steel making factory and EC(Evaporation Cooler), EP(Eltrostatic precititator) dust of the Kwangyang 2nd steel making factory are composed $\alpha$-Fe(21~50%), FeO(wustite)$Fe_3$$O_4$(magnetite), $Fe_2$$O_3$, CaO, $Al_2$$O_3$, $SiO_2$, and etc. 2. Pure iron has ductile characteristic in nature, particle size of the pure iron increase by increasing the grinding time. On the other hand, it is conformed that bo고 particles of hematite and magnetite become less than 325 mesh after 10 minutes grinding. 3. By applying the elutriation technique for the EC dust of the Kwangyang 2nd steel making factory, the iron powder of high content more than 99.17% of pure Fe was recovered with 37.8% yield at grinding time for 40 minutes. 4. By applying the elutriation technique for the CF dust of the Pohang 2nd steel making factory, the iron powder of high content more than 98.38% of pure Fe was recovered with 44.42% yield at grinding time for 40 minutes. 5. When magnetic separation was performed using plastic bonding magnet of 70 gauss, more than 98% Fe grade of iron powder was recovered in the size range +65 -200 mesh but the recovery of it was low.