• Current Research on Agriculture and Life Sciences
• /
• v.32 no.3
• /
• pp.131-134
• /
• 2014

The thermal death kinetics of the Black timber bark beetle, Xylosandrus germanus, was investigated to develop a heat treatment for control of infested wood packing materials used to export goods. To determine the feasibility of microwave irradiation as an alternative control method, laboratory experiments irradiating wooden blocks of Douglas fir ($200{\times}200{\times}250mm$), which were artificially infested with adults, with 2.45 GHz of microwave energy. All (100%) Ambrosia beetle adults were killed by both hot water treatments and microwave irradiation at $52^{\circ}C$ and $58^{\circ}C$, respectively. Probit analyses estimated the internal wood temperature required to produce Probit (0.99) efficacy to be $64.7^{\circ}C$ (95% CI $62.4-69.9^{\circ}C$) at one minute after microwave treatment.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.7 no.4
• /
• pp.86-96
• /
• 2008

In this paper, a new broadband rectenna is presented for the wireless transmission of microwave power. The new broadband rectenna element is based on a new printed monopole broadband antenna with size reduction using surface current distribution and a new broadband stub bandpass filter with suppression of second harmonics. A RF-to-DC conversion efficiency of 80% using a 270 ohm load resistor is obtain at 2.45 GHz. Also, a conversion efficiency of above 50 % is maintained from 1.8 GHz to 2.8 GHz.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.2
• /
• pp.18-23
• /
• 1992

Recently, SSPAs(Solid-State Power Amplifiers) with high linearity and efficiency replace TWTAs (Traveling-Wave-Tube Amplifiers) in satellite transponders. In this paper, a power amplifier with maximum output power is designed and constructed using GaAs FET(MGF-1302) as a test model for the development of SSPAs. For conjugate matching of input and output network, transimission lines and stubs are optimized using microwave CAD program, LINMIC+. Power amplifier is realized on the teflon substrate($\in$S1rT=2.45) with a bandwidth of 1GHz at a center frequency of 8GHz. Maximum stable gain of simulation and simulation and experimental result is obtained 9.23, 7.65 dB, respectively.

• Journal of the Korean Ceramic Society
• /
• v.41 no.1
• /
• pp.9-12
• /
• 2004

The effect of x wt% CuO-y wt% $V_2O_5$ content on the microwave properties of $(Pb_{0.45}Ca_{0.55})[(Fe_{0.5}Nb_{0.5})_{0.9}Sn_{0.1}]O_3$ (PCFNS) ceramics was investigated. In order to decrease the sintering temperature and use as a Low Temperature co-firing Ceramics (LTCC), CuO-$V_2O_5$ are added in the PCFNS. The bulk density, dielectric constant (${\varepsilon}_r$) and quality factor(Q${\cdot}f_0$) increased with increase in CuO content within a limited value. The microwave properties were degraded with increases in $V_2O_5$ content. The temperature coefficient of the resonant frequency (${\tau}_f$) of PCFNS was shifted to positive value abruptly with increasing the $V_2O_5$ content, while the ${\tau}_f$ was slightly shifted to positive value with increasing the CuO content. The optimized microwave properties, ${\varepsilon}_r$ = 88, Q${\cdot}f_0$ = 6100 (GHz), and ${\tau}_f$ = 18 ppm/$^{\circ}C$, were obtained in $(Pb_{0.45}Ca_{0.55})[(Fe_{0.5}Nb_{0.5})_{0.9}Sn_{0.1}]O_3$ with 0.2wt% CuO 0.05 wt% $V_2O_5$ and sintered at $1000^{\circ}C$ for 3 h. The relationship between the microstructure and microwave dielectric properties of ceramics was studied by X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM)

• Korean Journal of Materials Research
• /
• v.6 no.6
• /
• pp.576-584
• /
• 1996

The zirconia-alumina composite, a low loss material, was sucessfully sintered using a 2.45 GHz microwave radiation. The dense zirconia was used as a microware coupling aid. The effect of microwave power level on the heating rates of samples and the feasibility of microwave energy use in processign ceramec materials were obtained. It was also obtained how to accurately measure the temperature. According to the microwave heating theory, heating mechanisms were discussed.

• Journal of the Korean Society of Industry Convergence
• /
• v.2 no.1
• /
• pp.69-75
• /
• 1999

Intending to develop a new rubber curing process using only microwave, the both the characteristics of cure and the mechanical properties of rubbers for the tire tread, for which a green styrene-butadiene compounds had been cured with 2.45 GHz microwave, have been compared with those of the custom thermal cured rubber. The unintentional hot spot formation in the compound during the microwave curing has not found where the compound has a microwave absorbing ceramic powders in 4.18 weight percents and the supplying voltage has been adjusted to 90 volts. The new microwave process accomplished preheating to 418K in a quarter of the thermal cure time. The average tensile strength of the microwave-cured rubber indicating $190kg/cm^3$ was compatible to that of the thermal cure. In conclusion, the new microwave cure had approved to be applicable in a commercial plant.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.6
• /
• pp.792-797
• /
• 2013

In a indoor microwave power distribution system, matching-type power dividing switch is proposed and designed with a various power dividing ratio. A matching coaxial cable probe is used behind the output probe for the reflecting power absorption. Reflecting characteristics of the matching coaxial cable probe are calculated by analyzing the S-parameter of this structure. Newly proposed matching-type switch shows a very low return loss less than -30dB at the operating frequency of 2.45GHz with a dividing power ratio of 50.2%. The simulated results by use of 3-stage power divider shows a good agreement with the theoretical estimation for the various combination of the different switching ratio.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.6
• /
• pp.424-432
• /
• 2018

We herein analyze and study the shielding effectiveness characteristic of an open conveyor-belt-type microwave dryer that is widely used in industry. In particular, the electromagnetic wave leakage problem of the open-type conveyor belt dryer using a general-purpose 2.45-GHz magnetron was improved by applying the corrugated rectangular waveguide. We conducted the electromagnetic simulation of the optimal shielding effectiveness characteristic with regard to the proposed waveguide structure to analyze the attenuation characteristics of the corrugated rectangular waveguide. To verify the shielding effectiveness characteristic of the fabricated corrugated rectangular waveguide by IEEE standard 299, we achieved the shielding effectiveness of more than 30 dB in the practical microwave dryer with the proposed corrugated rectangular waveguide.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.3
• /
• pp.422-428
• /
• 2015

A 2.45GHz microwave plasma source with a linear antenna has been developed for low temperature large scale deposition processing. Microwave power is transmitted through WR340 waveguide and a copper rod, linear antenna, is located in a quartz tube. The power matching is effectively achieved by a linear antenna is located at ${\lambda}_g/4$ or $3{\lambda}_g/4$ from the end of WR340 waveguide. The Ar plasma was generated along the surface of quartz tube and a clear standing wave pattern with nearly 10cm wavelength was observed at Ar pressure of 200mTorr and 200W input power. The electron density and electron temperature were investigated by using the electrostatic probe. The electron density and electron temperature were highly measured near the surface of quartz tube. Ar plasma density along the quartz tube is mostly uniform despite standing wave set-up and antenna of long length. A uniform temperature was measured at 10~40cm distance from the end quartz tube and 5cm distance from the surface of quartz tube.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.862-867
• /
• 2009

This paper presents a study on a rectenna for rectification of incident low power microwave signals with power densities less than 2 mW/$cm^2$ at 2.45 GHz. The proposed rectenna is designed and implemented by a rectifier with voltage doubler structure and a printed Yagi antenna which suppress re-radiation of the second order harmonic of fundamental frequency. The printed Yagi antenna has a gain of about 5 dB, and the measured conversion efficiencies of the rectenna are from 32 % to 42 % when its incident power levels are from 0 dBm to 14 dBm. The developed rectenna is expected to be useful in the power transmission system.