• Journal of Environmental Science International
• /
• v.11 no.7
• /
• pp.679-686
• /
• 2002

Turbulence greatly influence on atmospheric flow field. In the atmosphere, turbulence is represented as turbulent diffusion coefficients. To estimate turbulent diffusion coefficients in previous studies, it has been used constants or 2-level method which divides surface layer and Ekman layer. In this study, it was introduced Smagorinsky method which estimates turbulent diffusion coefficient not to divide the layer but to continue in vertical direction. We simulated 3-D flow model and TKE equation applied turbulent diffusion coefficients using two methods, respectively. Then we showed the values of TKE and the condition of each term to TKE. The results of Smagorinsky method were reasonable. But the results of 2-level method were not reasonable. Therefor, it had better use Smagorinsky method to estimate turbulent diffusion coefficients. We are expected that if it is developed better TKE equation and model with study of computational method in several turbulent diffusion coefficients for reasonably turbulent diffusion, we will able to predict precise wind field and movements of air pollutants.

• Journal of Korea Water Resources Association
• /
• v.51 no.1
• /
• pp.61-70
• /
• 2018

This study examined how to determine the optimal sediment level in dam reservoir for efficient plan and operation of dam. Currently, Korea is applying a horizontally accumulated method for sediment level estimation for the safety design of dam and so the method estimated relatively higher level than others. However, the sediment level of dam reservoir should be accurately estimated because it is an important factor in assessing life cycle of a dam. The sediment level in dam reservoir can be determined by SED-2D model linked with RMA-2, horizontally accumulated method, area increment method, and empirical area reduction method. The estimated sediment level from each method was compared with the observed sediment level measured in 2007 in Imha dam reservoir, Korea and then the optimal method was determined. Also, the future sediment level was predicted by each method for the future trend analysis of sediment level. As the results, the most accurate sediment level was estimated by the empirical area reduction method and the future trend of sediment level variation followed the past trend. Therefore, we have found that the empirical area reduction method is a proper one for more accurate estimation of sediment level and it can be validated by the results from a numerical model of SED-2D linked with RMA-2 model.

• Interaction and multiscale mechanics
• /
• v.1 no.2
• /
• pp.191-209
• /
• 2008

In this paper, we model grain boundary evolution based on a multiple level set method. Grain boundary migration under a curvature-induced driving force is considered and the level set method is employed to deal with the resulting topological changes of grain structures. The complexity of using a level set method for modeling grain structure evolution is due to its N-phase nature and the associated geometry compatibility constraint. We employ a multiple level set method with a predictor-multicorrectors approach to reduce the gaps in the triple junctions down to the grid resolution level. A ghost cell approach for imposing periodic boundary conditions is introduced without solving a constrained problem with a Lagrange multiplier method or a penalty method. Numerical results for both uniform and random grain structures evolution are presented and the results are compared with the solutions based on a front tracking approach (Chen and Kotta et al. 2004b).

• Nuclear Engineering and Technology
• /
• v.50 no.8
• /
• pp.1234-1245
• /
• 2018

The risk of multi-unit nuclear power plants (NPPs) at a site has received considerable critical attention recently. However, current probabilistic safety assessment (PSA) procedures and computer code do not support multi-unit PSA because the traditional PSA structure is mostly used for the quantification of single-unit NPP risk. In this study, the main purpose is to develop a multi-unit Level 2 PSA method and apply it to full-power operating six-unit OPR1000. Multi-unit Level 2 PSA method consists of three steps: (1) development of single-unit Level 2 PSA; (2) extracting the mapping data from plant damage state to source term category; and (3) combining multi-unit Level 1 PSA results and mapping fractions. By applying developed multi-unit Level 2 PSA method into six-unit OPR1000, site containment failure probabilities in case of loss of ultimate heat sink, loss of off-site power, tsunami, and seismic event were quantified.

• Journal of the Korea Safety Management & Science
• /
• v.2 no.2
• /
• pp.29-40
• /
• 2000

In this paper, under JIT kanban system designed by Moeeni, each performance measures (service level, inventory level) identify the robust optimal level at a uncertain environment, and when there are multiple performance characteristics, it propose the optimal design-method and the optimal level decision-method, which consider multiple performance characteristics.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.2
• /
• pp.268-275
• /
• 2015

This paper proposes a method of switching to improve power loss for the single-phase three-level NPC inverter. The conventional switching methods, which are called as the bipolar and unipolar switching methods, are used for single phase inverters using three-level topology. However, these switching method have disadvantage in the power loss. Because all of the switch are operated. To reduce the power loss of the three-level NPC inverter, clamp switching method is introduced in this paper. This way, one of the lag is fixed that switching loss is reduced. This paper analyzes and compares power losses of unipolar method and clamp method. The validity of the power loss analysis is verified through the simulation and experimental results.

• KIPS Transactions on Software and Data Engineering
• /
• v.2 no.12
• /
• pp.865-872
• /
• 2013

Two-level morphology analysis method is one of rule-based morphological analysis method. This approach handles morphological transformation using rules and analyzes words with morpheme connection information in a lexicon. It is independent of language and Korean Two-level system was also developed. But, it was limited in practical use, because of using very small set of lexicon built manually. And it has also a over-generation problem. In this paper, we propose an automatic construction method of Korean Two-level lexicon for PC-KIMMO from morpheme tagged corpus. We also propose a method to solve over-generation problem using lexical information and sub-tags. The experiment showed that the proposed method reduced over-generation by 68% compared with the previous method, and the performance increased from 39% to 65% in f-measure.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.263-269
• /
• 2018

In this study, a selective inverter operation between a 2-level voltage source converter (VSC) and a 3-level T-type VSC (3LT VSC) is proposed to improve the efficiency of a 3LT VSC. The 3LT VSC topology, except for its neutral-point switches, has similar operations as that of the 2-level VSC. If an operation mode is changed according to efficiency, the efficiency can be improved because efficiencies of each methods are depending on current and MI (Modulation Index). The proposed method calculates the power losses of the two topologies and operates as the having lower losses. To calculate the losses, the switching and conduction losses based on the operation mode of each topology were analyzed. The controller determined the operation mode of the 2- or 3-level VSC based on the power loss calculated during every cycle. The validity of the proposed control scheme was investigated through simulation and experiments. The waveform and average efficiency of each method were compared.

• The Journal of Korean Academy of Prosthodontics
• /
• v.42 no.2
• /
• pp.238-247
• /
• 2004

Statement of problem: Major objective in making on implant-supported prosthesis is the production of superstructure that exhibits a passive fit when connected to multiple abutments. One requirement to ensure passive fit is to make an accurate impression. Purpose : The purpose of this study was to compare the accuracy of master cast fabricated by using different impression methods at the different impression levels. Material and method: The master model used in this study was resin block having low implant analogs. Impression method studied were 1) direct method on fxiture level (Group FIX-D), 2) indirect method on fixture level(Group FIX-I), 3) modified indirect method on fixture level(Group FIX-M), 4) direct method on abutment level(Group AB-D) and 5) indirect method on abutment level(Group AB-I). Each of the five groups took 10 impressions. Fifty impressions were made for master cast by using Impregum $F^{(R)}$ impression material loaded on individual tray. Three dimensional measuring microscope was used to measure the inter-implant distance. Error rate of each inter-implant distance were calculated and evaluated. Results : The results were as follows. 1. Group FIX exhibited higher accuracy than group AB. 2. In group FIX, modified indirect method showed the highest accuracy, while indirect method showed the lowest accuracy. In group Ab, indirect method showed the higher accuracy than direct method. 3. Group FIX showed larger horizontal error than group AB. But, group AB showed the larger vertical error than group FIX. 4. Group Fix-M showed smallest vertical and horizontal error. Conclusion: An impression method have more effect on accuracy of master model than an impression level. A modified indirect method showed smallest vertical and horizontal error.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.19 no.5
• /
• pp.706-712
• /
• 2009

In this paper, a fault diagnosis method is proposed to detect and classifies faults that occur in press process line. An oil level automatic monitoring method is also presented to detect oil level. The FFT(fast fourier transform) frequency analysis and ART2 NN(adaptive resonance theory 2 neural network) with uneven vigilance parameters are used to achieve fault diagnosis in proposing method, and GUI(graphical user interface) program for fault diagnosis and oil level automatic monitoring using LabVIEW is produced and fault diagnosis was done. The experiment results demonstrate the effectiveness of the proposed fault diagnosis method of induction motors and oil level automatic monitor system.