• 한국재료학회지
• /
• 제24권4호
• /
• pp.180-185
• /
• 2014

The current concern about these materials ($MoSi_2$ and $NbSi_2$) focuses on their low fracture toughness below the ductile-brittle transition temperature. To improve the mechanical properties of these materials, the fabrication of nanostructured and composite materials has been found to be effective. Nanomaterials frequently possess high strength, high hardness, excellent ductility and toughness, and more attention is being paid to their potential application. In this study, nanopowders of Mo, Nb, and Si were fabricated by high-energy ball milling. A dense nanostructured $MoSi_2-NbSi_2$ composite was simultaneously synthesized and sintered within two minutes by high-frequency induction heating method using mechanically activated powders of Mo, Nb, and Si. The high-density $MoSi_2-NbSi_2$ composite was produced under simultaneous application of 80MPa pressure and an induced current. The sintering behavior, mechanical properties, and microstructure of the composite were investigated. The average hardness and fracture toughness values obtained were $1180kg/mm^2$ and $3MPa{\cdot}m^{1/2}$, respectively. These fracture toughness and hardness values of the nanostructured $MoSi_2-NbSi_2$ composite are higher than those of monolithic $MoSi_2$ or $NbSi_2$.

• 한국세라믹학회지
• /
• 제29권10호
• /
• pp.797-805
• /
• 1992

Al2O3-20 wt% ZrO2 composite powders to be used as the starting materials of the Al2O3/ZrO2-Spinel composite system were prepared by the use of the emulsion-hot kerosene drying method. The crystalline phase of ZrO2 in the synthesized Al2O3-ZrO2 composite powders was 100% tetragonal but the small amount of t-ZrO2 was transformed into m-ZrO2 after crushing. The hardness, fracture toughness, and flexural strength of the composite, which was sintered at 1650$^{\circ}C$ for 4 hrs after calcining at 1100$^{\circ}C$ for 2 hrs and had the relative density of 99%, were 15.7 GPa, 4.97 MN/m3/2, and 390 MPa, respectively. The fracture form in the sintered composites was found to be the intergranular fracture.

• 한국재료학회지
• /
• 제14권9호
• /
• pp.649-654
• /
• 2004

In this paper, the fracture toughness and mechanisms of failure in a random SiC-whisker/$Al_{2}O_3$ ceramic composite were investigated using in situ observations during mode I(opening) loading. $SiC_{w}/Al_{2}O_3$ composite was obtained by hot press sintering of $Al_{2}O_3$ powder and SiC whisker as the matrix and reinforcement, respectively. The whisker and powder were mixed using a turbo mill. The composite was produced at SiC whisker volume fraction of $0.3\%$. Compared with monolithic $Al_{2}O_3$, fracture toughness enhancement was observed in $SiC_{w}/Al_{2}O_3$ composite. This improved fracture toughness was attributed to SiC whisker bridging and crack deflection. $SiC_{w}/Al_{2}O_3$ composite exhibited typically brittle fracture behavior, but a fracture process zone was observed in this composite. This means that the load versus load-line displacement curve of $SiC_{w}/Al_{2}O_3$ composite from a fracture test may involve a small non-linear region near the peak load.

• 한국재료학회지
• /
• 제18권7호
• /
• pp.389-393
• /
• 2008

Nano-sized $TiO_2$-60 wt% SrO composite powders were synthesized by a sol-gel method using titanium isopropoxide and $Sr(OH)_2\;{\cdot}\;8H_2O$ as precursors. 3, -5, -7 wt%Ag spot-coated $TiO_2$-60 wt% SrO composite powders were synthesized by a Ag electroless deposition method using $TiO_2$-60 wt% SrO composite powders calcined at $1050^{\circ}C$, which mainly exhibited the $SrTiO_3$phase. However, a small number of rutile $TiO_2$, $Sr_2TiO_4$ and $SrO_2$ phases were also detected. In the Ag spot-coated powders synthesized by electroless deposition, nano-sized particles about 5-25 nm in diameter adhered to the $TiO_2$-60 wt% SrO composite powders. The photocatalytic activity of Ag spot-coated $TiO_2$-SrO and $TiO_2$-SrO composite powders for degradation of phenol showed that all of $TiO_2$-SrO composite powders were highly active under UV light irradiation. 7 wt%Ag spot-coated $TiO_2$-60wt.%SrO composite powders had a relatively higher photocatalytic activity than did $TiO_2$-SrO composite powders under visible light.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.1278-1282
• /
• 2004

수열처리법으로 nano-sized $CeO_2$ 입자를 $Al_3O_3$ 입자의 표면에 균일하게 코팅하여 $AL_2O_3/O_2$ composite 연마 입자를 제조하었다. 제조된 $Al_2O_3\CeO_2$ composite 입자의 뭍성을 TEM, XRD, zeta potential analyzer 및 particle size analyzer로 측징하였다. $Al_2O_3/CeO_2$ composite 입자와 구성된 슬러리와 비교 시료로서 $Al_2O_3$와 $CeO_2$ 입자를 혼합한 슬러리를 사용하여 thermal oxide film에 대한 연마특성을 평가하였다. 연마슬러리에 포함된 $A1_2O_3/CeO_2$ composite 입자와 $Al_2O_3$와 $CeO_2$ 혼합입자에서 나노 크기의 세리아 입자가 sub-micron 크기의 알루미나 입자의 표면에 균일하게 코팅되므로서 $Al_2O_3$ 단일 성분의 슬러리에 비해 removal rate(RR)는 106 nm/min, WIWNU는 $8\sim9%$, roughness는 $2.6{\AA}$의 향상된 연마 특성을 나타내었다. 알루미나 입자의 불규칙한 형상 때문에 $Al_2O3/CeO_2$ composite 슬러리와 $Al_2O_3$ 와 $CeO_2$ 혼합슬러리의 연마 특성이 비슷한 수준을 나타내었다.

• International Journal of Ocean System Engineering
• /
• 제2권4호
• /
• pp.244-249
• /
• 2012

In this study, a monolithic MoSi2 matrix reinforced with 20 vol% SiC particles, a SiC/MoSi2 composite matrix reinforced with 20 vol% ZrO2 particles, and a ZrO2/MoSi2 composite were fabricated using hot press sintering at $1350^{\circ}C$ for 1 h under a pressure of 30 MPa. The Vickers hardness and sliding wear resistance of the monolithic MoSi2, ZrO2/MoSi2, and SiC/MoSi2 composite were investigated at room temperature. A wear behavior test was carried out using a disk-type wear tester with a silicon nitride ball. The ZrO2/MoSi2 composite showed an average Vickers hardness value and excellent wear resistance compared with the monolithic MoSi2 and SiC/MoSi2 composite at room temperature.

• Elastomers and Composites
• /
• 제46권1호
• /
• pp.60-69
• /
• 2011

[ $2.1\;{\mu}m$ ]입자경의 단분산 PBA seed를 이용한 2단계 분산중합을 seeded batch process 와 seeded semi-continuous process를 이용하여 다양한 형태의 PBA/PMMA composite 미립자를 제조하였다. Batch process의 경우 PBA/PMMA composite 입자의 모폴로지는 중합 분산매인 methanol/water 비와 중합 2단계에서의 PBA seed/MMA단량체의 비에 따라 크게 영향을 받으며, methanol/water 중합분산매중 물의 량이 증가함에 따라, 그리고 중합 2단계에서 MMA단량체량이 증가함에 따라 PBA와 PMMA간의 상분리현상이 심화되어 구형의 입자로부터 egg, snowman, confetti, peanut와 같은 비구형의 PBA/PMMA composite 입자들이 제조되었다. Semi-continuous process의 경우 단량체 부가시간을 조절함으로서 PBA/PMMA composite 입자의 모폴로지가 변함을 발견하였고 특히, 단량체의 결핍된 조건하에서 구형의 PBA(코어)/PMMA(쉘) composite 라텍스가 제조되었다.

• Steel and Composite Structures
• /
• 제19권3호
• /
• pp.777-787
• /
• 2015

Production and properties of metal matrix composites reinforced with an in-situ high aspect ratio $AlB_2$ flake have been investigated. Boron 2.2wt.% was dissolved in pure Al and Al-Cu alloy at $1300^{\circ}C$ by adding directly boron oxide which resulted in 4 vol.% reinforcing phase. The in-situ $AlB_2$ flake concentration was increased up to 30 vol.% in order to increase the tensile strength of the composites. Hardness, compressive strength and tensile strength of the composite were measured and compared with their matrix. Results showed that 30 vol.% $AlB_2/Al$ composite show a 193% increase in the compressive strength and a 322% increase in compressive yield strength. Results also showed that ductility of composites decreases with adding $AlB_2$ reinforcements.

• 한국표면공학회지
• /
• 제52권4호
• /
• pp.187-193
• /
• 2019

Electroless Ni-P coatings are widely used in the chemical, mechanical, and electronic industries because of their excellent wear and abrasion resistance. In this study, the effect of $TiO_2$ particles of composite coating was investigated. To improve the corrosion resistance, electroless $Ni-P-TiO_2$composite coating was studied by varying the $TiO_2$ content. The morphology and phase structure of $Ni-P-TiO_2$ composite coatings were analyzed by scanning electron microscopy(SEM), X-ray diffractometry(XRD) and X-ray photoelectron spectroscopy(XPS). The result showed that $Ni-P-TiO_2$composite coating is composed of Ni, P, Ti and O. It exhibits an amorphous structure, high hardness and good corrosion resistance to the substrate. $Ni-P-TiO_2$ composite coatings have higher open circuit potential than that of the substrate, which obtained at $TiO_2$ content of 5.0 g/L optimal integrated properties.

• 한국세라믹학회지
• /
• 제26권1호
• /
• pp.139-145
• /
• 1989

An eutectic melt in the system(Bi2O3)0.85·(Nb2O5)0.15-6Bi2O3·SiO2 was unidirectionally solidfield at a rate of 0.5mm/h under a thermal gradient of 100℃/cm. Double crucibles and seed crystal plate were used in order to botain the composite crystals which had uniform microstructure throughout the ingot. The obtained composite crystals showed uniform microstructure, in which needle-like δ-(Bi2O3)0.85·(Nb2O5)0.15 crystals were arrayed in parallel in a matrix of γ-6Bi2O3·SiO2 single crystal. It was found that the <110> direction of δ-(Bi2O3)0.85·(Nb2O5)0.15 crystal was essentially parallel to the <111> direction of γ-6Bi2O3·SiO2 crystal in the composite crystals. A transverse thin plate of the composite crystals showed a high resolution optical transmission like an optical fiber array, and sharp chatoyancy was observed in the cabochon shaped composite crystals. Then, this may be useful for applications such as screen of a cathode ray tube or artificial cat's eye gem stones.