• Journal of IKEEE
• /
• v.1 no.1 s.1
• /
• pp.55-63
• /
• 1997

The purpose of this paper is to realize robust vector control of an induction motor without speed sensor. In order to do it, the speed of an induction motor is estimated using model reference adaptive system(MRAS) and two rotor flux observers which have robustness to the parameter variation are employed as the reference model and the adjustable model in MRAS speed estimator. The MRAS-based overall control scheme has been implemented on 2.2kW induction motor control system and it is verified that the proposed speed sensorless control scheme is more stable and robust than the conventional schemes.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.114-121
• /
• 2002

This paper describes the control system of the toroidal traction driver continuously variable-speed transmission(CVT) fur a tractor. The instrumentation system, the hydraulic power control system and the principle control scheme were introduced. Experimental tests in the bench and the tractor were conducted to validate the performance of the CVT utilizing the proposed controller. The speed of the vehicle was continuously changed to follow the speed set by driver under various operating conditions. Given the reduction ratio of the variator from 2.0 to 1.0, the settling time was about just 0.52 seconds which was satisfactory value for working with the tractor. It was also proved that the tractor could work with continuously variable speed under heavy load disturbances.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.7
• /
• pp.1112-1120
• /
• 1994

This paper presents a servo control scheme for the surface-mounted permanent-magnet synchronous motor(SPMSM) which essentially uses vector control algorithm. The control system is composed of the PI controller for speed control and the current controller using space voltage vector PWM technique. The high-speed calculation and processing for vector control is carried out by TMS320C31 digital signal processor and IGBT module. The proposed scheme is verified through digital simulations and experiments for 2.2kW SPMSM and shows good dynamic performance.

• Journal of Ocean Engineering and Technology
• /
• v.15 no.1
• /
• pp.67-72
• /
• 2001

In this study, a methodology of synchronous control which can be applied to position synchronization of a two-axes driving system has been developed. The synchronous error is caused by model uncertainties and torque disturbance of each axis. To overcome these problems, the proposed synchronous control system has been composed of two speed controllers, disturbance observers, and one synchronous controller. The speed controllers, based on the PID control law are aimed at the following to speed reference. And the parameters of speed controllers have been designed in order for the speed response fo the second axis to correspond with the one of the first axis. The disturbance observer has been designed to restrain the torque disturbance. The synchronous controller eliminates the synchronous error by controlling the speed of the second axis. The effectiveness of the proposed method has been verified through simulation.

• Journal of the Korean Society for Railway
• /
• v.13 no.2
• /
• pp.166-172
• /
• 2010

Currently, vector control is used for speed control of trains because induction motor has high performance is installed in Electric railroad systems. Also, control of the induction motor is possible through various methods by developing inverters and control theory. Presently, rolling stocks which use the induction motor are possible to brake trains by using AC motor. Therefore model of motor block and induction motor is needed to adapt various methods. There is Variable Voltage Variable Frequency (VVVF) as the control method of the induction motor. The torque and speed is controlled in the VVVF. The propulsion system model in the electric railroad has many sub-systems. So, the analysis of performance of the speed control is very complex. In this paper, simulation models are suggested by using Matlab/Simulink in the speed control characteristic. On the basis of the simulation models, the response to disturbance input is analyzed about the load. Also, the current, speed and flux control model are proposed to analyze the speed control characteristic in the train propulsion system.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.11
• /
• pp.1027-1033
• /
• 2015

For the attitude control of spacecraft, two variable-speed control moment gyros are proposed as main actuators in the article. Since a variable-speed control moment gyro (VSCMG) makes two control torques (gyroscopic torque and reaction torque), two VSCMGs are sufficient for controlling 3-axes attitude. Additionally, there are no singular conditions for two non-parallel VSCMGs. Since gyroscopic torque is usually much greater than reaction torque, the control performances of approximately 3 axes may not be the same. However, several missions can be accomplished by controlling two axes. For such missions, a selective axes control method is proposed. The method selects two axes for a certain task and controls the attitude of the selected axes. For the remaining axis, angular speed is controlled for stabilization. A hardware-in-the-loop simulation has been used to test VSCMG modules and to verify the proposed method. Two VSCMGs can be alternative actuators for small satellites.

• The KSFM Journal of Fluid Machinery
• /
• v.16 no.6
• /
• pp.5-11
• /
• 2013

Torque control methods of wind turbine are mainly classified into two methods: torque-mode and speed-mode methods. The traditional torque-mode method, in which generator torque proportional to square of generator speed is determined, has been chosen in many wind turbines but its response is slower as they are larger in multi-MW size. Torque control methods based on both speed-mode and torque-mode can be used to make response of wind turbine faster. In this paper, two torque control methods based on the traditional torque-mode method are applied to a 2.75 MW wind turbine. It is shown through some simulation results for real turbulence wind speeds that torque control method based on torque-mode has the merit of reducing fluctuations of generated power than PI controller based on speed-mode.

• Journal of Power Electronics
• /
• v.16 no.2
• /
• pp.798-804
• /
• 2016

This paper proposes a new operation and control strategy for Power-Assisted Wheelchairs (PAW) using one brushless DC (BLDC) motor. The conventional electrical wheelchairs are too heavy and large for one person to move because they have two electric motor wheels. On the other hand, the proposed PAW system has a small volume and is easy to move due to the presence of a single wheel motor. Unlike the conventional electric wheelchairs, this structure for a PAW does not have a control joystick to reduce its weight and volume. To control the wheelchair without a joystick, a special control system and algorithm are needed for proper operation of the wheelchair. In the proposed PAW system uses only one sensor to detect the acceleration and direction of PAW's movement. By using this sensor, speed control can be achieved. With a speed control system, there are three kinds of operations that can be done on the speed of a PAW: the increment of PAW speed by summing external force, the decrement of PAW speed by subtracting external force, and emergency breaking by evaluating the time duration of external force. The validity of the proposed algorithm is verified through experimental results.

• Journal of Power Electronics
• /
• v.19 no.2
• /
• pp.497-508
• /
• 2019

The predictive speed control (PSC) strategy can realize the simultaneous control of speed and current by using one cost function. As a model-based control method, the performance of the PSC is vulnerable to model mismatches such as load torque disturbances and parameter uncertainties. To solve this problem, this paper presents a robust predictive speed control (RPSC) strategy for surface-mounted permanent magnet synchronous motor (SPMSM) drives. The proposed RPSC uses extended state observers (ESOs) to estimate the lumped disturbances caused by load torque changes and parameter mismatches. The observer-based prediction model is then compensated by using the estimated disturbances. The introduction of ESOs can achieve robustness against predictive model uncertainties. In addition, a modified cost function is designed to further suppress load torque disturbances. The performance of the proposed RPSC scheme has been corroborated by experimental results under the condition of load torque changes and parameter mismatches.

• Journal of Wind Energy
• /
• v.2 no.1
• /
• pp.82-89
• /
• 2011

his dissertation is on power control system for MW-class wind turbine. Especially, the control purpose is reduction in electrical power and rotor speed. The base control structure is power curve tracking control using variable speed variable pitch operational type. For the reduction of fluctuations, more control algorithm is needed in above rated wind conditions. Because general pitch control system is low dynamic response as compared with the wind speed change. So, this paper introduces about the pitch feed forward control to minimize fluctuations of the electrical power and rotor speed. To maintain rated electrical power, the algorithm of feed forward control adds feed forward pitch amount to the pitch command of power curve tracking control. The effectiveness of the feed forward control is verified through the simulation.