• Composites Research
• /
• v.34 no.2
• /
• pp.77-81
• /
• 2021

Due to the high specific strength and stiffness of the composite materials, the composite materials have been extensively used in various industries. In particular, carbon fiber reinforced composites are widely used in many mechanical structures. In addition, since carbon fiber reinforced composites have anisotropic properties, to understand the fatigue behavior of composites with different fiber orientation is very important for the efficient structural design. Therefore, in this paper, the effect fiber orientation on the fatigue life of composite materials was experimentally evaluated. For this purpose, tensile and fatigue tests were performed on the off-axis specimens (0°, 10°, 30°, 45°, 60°, 90°) of the composite materials. As a result of the fatigue tests, the fatigue strength of the composites decreased significantly as the fatigue strength slightly deviated from 0 degrees. On the other hand, the more deviated, the less decreased. This is because the role of supporting the load of fibers decreased as the stacking angle increased. In addition, the fatigue behavior was analyzed by introducing a fatigue strength ratio (Ψ) that eliminates the fiber orientation dependence of the off-axis fatigue behaviors on the unidirectional composites. The off-axis fatigue S-N lines can be reduced to a single line regardless of the fiber orientation by using the fatigue strength ratio (Ψ). Using the fatigue Ψ-N line, it is possible to extract back to any off-axis fatigue S-N lines of the composites with different fiber orientations.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.136.2-136.2
• /
• 2005

• Journal of the KSME
• /
• v.36 no.9
• /
• pp.855-866
• /
• 1996

승요차 앞자축에 장착되어 회전하면서 동력을 전달하는 드라이브축은 운행중에 주로 비틀림하중을 받는다. 따라서 동 부품의 피로해석 및 설계를 위해서는 실제 운행중에 받는 서비스토크의 크기, 주파수 등에 관한 데이터가 필요하다. 차량에 탑재된 엔진의 토크와 회전수 등의 규격으로부터 드라이브축에 부가되는 최대 토크 값을 예측할 수 있으나, 자동차 운행주에는 승차인원, 도로조건, 운전자의 운전습관 등 여러가지 외적인 영향으로 인하여 서비스토크가 불규칙하게 변할 것으로 예상되므로 서비스토크를 정확히 예측하기는 어려운 실정이다. 또한, 최근의 자동차 구조부품에 대한 설계개념이 무한수명 설계에서 경량화 설계로 변화되고 있으며, 따라서 자동차 드라이브축도 실제 운용하중을 바탕으로 한 정확한 수명예측 및 강도설계가 요구되고 있다. 본 연구에서는 4륜구동형 승용차용 드라이브축에 대해 실제 운용하중에서의 피로수명을 예측하기 위해 1)텔리메트리를 이용하여 토크를 측정하고, 2) 일정진촉하중하에서의 드라이브축의 비틀림 피로시험을 수행하고, 3) 일정진폭하중하에서의 드라이브축의 비틀림 피로시험을 수행하고, 4) 축류 소재의 피로특성 데이터를 구성하여 5) 자체 개발한 프로그램으로 피로수명을 예측하고자 한다.

• Journal of the Korea Concrete Institute
• /
• v.22 no.2
• /
• pp.263-271
• /
• 2010

The purposes of this study is to verify the fracture characteristic of steel which is manufactured in Korea, subjected to cyclic loading. This investigation deals with the low cycle fatigue behavior of longitudinal reinforcement in reinforced concrete bridge substructure (piles and columns of piers). Eighty-one specimens of longitudinal reinforcement were tested under axial strain controlled reversed cyclic tests with strain amplitudes. The selected test variables are ratio of tension strain to compression strain, yield stress of longitudinal reinforcement, ratio of diameter of longitudinal steel to clear length of longitudinal steel, size of longitudinal steel and strain amplitudes. Low cycle fatigue behavior and low-cycle fatigue life are investigated and discussed in this paper.

• Journal of Welding and Joining
• /
• v.22 no.2
• /
• pp.3-7
• /
• 2004

재료에 단순 인장시험에 의해 구한 항복강도의 2/3의 축응력을 부가하면, 소성변형과 파괴는 일어나지 않지만, 상당한 사이클로 반복하여 부가하면, 파괴가 일어난다. 이것을 피로파괴라고 한다 대부분의 구조물이나 기계부품은 재료의 항복응력 이하의 반복하중을 받으면서 작동되므로, 피로파괴가 자주 발생한다.(중략)

• Journal of the Korean Society for Nondestructive Testing
• /
• v.22 no.5
• /
• pp.539-544
• /
• 2002

The purpose of this study is to examine the change of full width half maximum(FWHM) and residual stress during fatigue process in S45C Steel, by X-ray diffraction. For S45C Steel, the relationship between the change in fatigue damage of the specimen and the FWHM, and residual stress of X-ray diffraction profiles during the fatigue processes has been investigated. The FWHM decreases in the early period of fatigue cycle. The change of FWHM is associated with cyclic work hardening. The change of the FWHM is not significant in $10{\sim}20%$ of ratio of fatigue life. The residual stress is changed with fatigue cycle increasing during the fatigue pro process.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.2
• /
• pp.276-282
• /
• 2012

This study looked for Mode status of each for fatigue crack growth behavior about the repeat load of mode I and the static load of mode II. The experiment was performed in the state of the repetition frequency of the sine wave 10Hz, the stress ratio 0.1, maximum load 300kg.f, a static load 0, 100, 200, 300kg.f, As the experimental results, in mode of static load, while the load value increases, the crack growth rate is slower as the energy of a crack mixing grows. Mode I and the power mode II get an influence each other in the direction of crack propagation path, but as they eventually get closer to the breaking point of the crack growth, it is dominated by the mode I.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.4
• /
• pp.410-418
• /
• 2004

The multiaxial fatigue test under in-phase and out-of$.$phase load were performed to study what degradation phenomenon affects fatigue life with virgin and 3600 hrs degraded materials. The various kind of fatigue data fur fatigue life prediction were acquired under pure axial and pure torsional load of fully reversal condition. The models which was investigated are: 1) the von Mises equivalent strain range, 2) the critical shear plane approach method of Fatemi-Socie(FS) parameter, 3) the modified Smith-Watson-Topper(SWT) parameter. The result showed that, fatigue life by material degradation are decreased and life prediction which was used the FS parameter is not conservative but the best result.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.6 s.237
• /
• pp.815-821
• /
• 2005

Biaxial low cycle fatigue test was carried out to predict fatigue life under combined axial-torsional-loading condition which is that of in-phase and out-of-phase for CF8M cast stainless steels. Fatemi-Socie(FS) parameter which is based on critical plane approach is not only one of methods but also the best method that can predict fatigue life under biaxial loading condition. But the result showed that, biaxial fatigue life prediction by using FS parameter with several different parameters for the CF8M cast stainless steels is not conservative but best results. So in this present research, we proposed new fatigue life prediction parameter considering effective shear stress instead of FS parameter which considers the maximum normal stress acting on maximum shear strain and its effectiveness was verified.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.6
• /
• pp.565-571
• /
• 2016

This paper investigates macro- and microscopic fractography performed on fracture specimens from low cycle fatigue (LCF) testings through an Alloy 617 base metal and weldments. The weldment specimens were taken from gas tungsten arc welding (GTAW) pad of Alloy 617. The aim of the present study is to investigate the macro- and microscopic aspects of the low cycle fatigue fracture mode and mechanism of Alloy 617 base metal and GTAWed weldment specimens. Fully axial total strain controlled fatigue tests were conducted at room temperature with total strain ranges of 0.6, 0.9, 1.2 and 1.5%. Macroscopic fracture surfaces of Alloy 617 base metal specimens showed a flat type normal to the fatigue loading direction, whereas the GTAWed weldment specimens were of a shear/star type. The fracture surfaces of both the base metal and weldment specimens revealed obvious fatigue striations at the crack propagation regime. In addition, the fatigue crack mechanism of the base metal showed a transgranular normal to fatigue loading direction; however, the GTAWed weldment specimens showed a transgranular at approximately $45^{\circ}$ to the fatigue loading direction.