• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.183-187
• /
• 2011

본 연구에서는 3차원 수리해석과 함께 유사의 이송, 침식, 퇴적 현상을 연동하여 모의할 수 있는 유한차분 수치모형인 EFDC(Environmental Fluid Dynamics Code)를 이용하여 주운하천 구간으로 유입되는 다입경 혼합유사의 입경별 시 공간적 퇴적분포 특성을 고찰하고, 하상변동 예측에 있어서 유사의 밀도와 모델의 유한차분 격자 구조에 의한 불확실성 해석을 수행하였다. 유입 유사의 입경별 공간적 퇴적특성은 하천 하류부와 단면 확대부에서 발생하는 3차원적 수리현상과 매우 밀접한 상관성을 보였으며, 굴포천과 합류하는 주운수로 유입부에서는 대부분 입경이 큰 비점착성 유사($63{\mu}m$ 이상)인 사질(sand)입자들이 주로 퇴적되는 것으로 나타났으며, 주운하천 합류부로부터 하류구간까지는 $4\sim63{\mu}m$ 입자의 실트질(silt) 유사가 대부분 이송되어 퇴적되는 것으로 분석되었다. 점착성 유사인 $4{\mu}m$ 이하의 점토(clay)는 단면이 확대되어 유속이 매우 느린 구간이나 사수역을 중심으로 퇴적되는 것으로 나타났다. 단면 횡방향 분포특성은 굴포천과 주운하천이 합류하는 합류부 구간의 주흐름 방향 남쪽에서 흐름의 정체구간이 발생되어 퇴적이 발생하고, 단면 급확대부 양안에서 사수역이 형성되므로 퇴적이 지배적으로 발생되었다. 하상변동 예측의 불확실성 해석을 위해 유사 밀도값에 대한 민감도 분석결과, 하상변동량은 유사밀도($1.3ton/m^3\sim2.65ton/m^3$)가 감소됨에 따라 약 2배까지 증가하는 것으로 분석되어 민감도가 매우 크게 나타났다. 또한 수치격자 구조의 민감도 분석결과, 수층을 3개 층으로 분석한 결과가 단일층 분석결과보다 최대 6배의 하상변동량이 많게 산정되었다. 이는 수심방향의 유속과 부유사 농도의 불균등 분포특성이 실제 자연현상에 더 가깝게 모의되기 때문으로 판단되었다.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.6 no.3
• /
• pp.3-14
• /
• 1995

The broadband input impedance, the input power and the radiation pattern of the monopole antenna attached to the handy phone operated at 800MHz are calculated by using the Finite Difference Time Domain(FDTD) Method. For the FDTD analysis of frequency characteristics of monopole antenna, the handy phone is modeled with the geometry that the monopole antenna is connected to a conducting box, and the modified FDTD algorithm[11] used the thin wire appproximation method and the Maxwell's integral equation from the original Yee algorithm is applied for the analysis of the wire structure. Also, by means of finding the current distribution directly from circumferencial magnetic filelds around the monopole antenna and the conducting box, the radiation pattern is calculated to observe the influence of the conducting box, and is compared with the results of the known mothod for the FDTD calculation of radiation pattern, For the experiments, the handy phone of which full length including antenna is .lambda. $\lambda$/2 is manufactured and we confirm that all computation results are agree well with the mea- sured values.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.1397-1401
• /
• 2007

낙동강에 위치한 하회마을의 점사주는 상류에 안동 및 임하 다목적댐이 건설되면서, 수량이 조절됨에 따라 토사수리학적 특성이 상당히 변화되었으며, 식생이 발생하는 등 옛 모습을 상실해 가고 있는 지역이다. 이 연구는 낙동강의 중상류에 위치한 하회지구에 평면 이차원 하상변동 및 수질예측 수치모형인 KU-RLMS 모형을 적용하여 하회마을 앞의 점사주에 영향을 미치는 수리학적 특성 변화를 규명할 목적으로 수행하였다. KU-RLMS 모형은 하천 및 저수지의 국부적인 수리, 수질, 유사이동 해석을 위해 개발된 평면 이차원 비정상 수치모형이다. 직사각형 격자를 사용하는 유한차분법의 단점을 보완하기 위해, 흐름 계산을 위한 지배 방정식은 3차원 Reynolds 방정식으로부터 수심적분된 2차원 연속방정식과 운동량방정식을 불규칙한 경계를 현실적으로 모사할 수 있는 직교곡선 좌표계로 변환한 방정식을 사용한다. 안동다목적댐과 임하다목적댐의 방류량, 수공구조물 설치 여부 등을 고려하여 수치모의조건을 결정하였으며, 각 조건에 대한 흐름 변화특성을 분석하였다.

• Journal of Korea Water Resources Association
• /
• v.30 no.6
• /
• pp.597-610
• /
• 1997

One-dimensional numerical models using finite difference methods for unsteady sediment transport on alluvial river channel are developed. The Preissmann implicit scheme and the Lax-Wendroff two-step explicit scheme with the Method of Characteristics for water motion and a forward time centered space explicit scheme for sediment motion are developed to simulate the sediment transport rate and the variation of channel bed level. The program correctness of each model is successfully verified using volume conservation tests. The sensitivity studies show that higher peak stage level, steeper channel slope and longer flooding duration produce more channel bed erosion. and median grain size, $D_{50}=0.4mm$ give maximum volume loss in this study. Finally, the numerical models are found to produce reasonable results from the various sensitivity tests which reveal that the numerical models have properly responded to the changes of each model parameter.

• Water for future
• /
• v.22 no.1
• /
• pp.81-90
• /
• 1989

A numerical simulation technique of three-dimensional finite difference model is developed to study the groundwater flow system in Dejima, an upland area which faces Kasumigaura Lake. For general perspectives of the groundwater flow system, a steady state three-dimensinal model is simulated. For the sedimentary mud formations which are found in the representative formation, three situations where the horizontal permeability is equal to 10 times and 100 times of the vertical one. The finite difference grid used in the simulation has 60$\times$50$\times$30=90,000 nodes. A converged solution with a tolerance of 0.001 meter of hydraulic head is set. Having determined the flow net by using a steady state three-dimensional model, the results for the three cases of hydraulic conductivity are compared with the results of the tracer methods (Bae and Kayane, 1987). With the aid of four representative vertical cross-sections, groundwater flow systems in the study area are assumed. The results of these are reasonally good comparable with the results of the basin yield and thd recharge-discharge distribution 8.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.12B
• /
• pp.2335-2341
• /
• 1999

The $2\times32$ coupler consists of Mach-Zehnder interferometer and Y branch coupler. For the designs of this coupler, three dimensional rectangular core waveguide decomposed to two-dimensional structure by the effective index method. To optimize the waveguide structure, the confinement factor was investigated with two-dimensional finite difference Beam Propagation Method. The $2\times32$ coupler fabricated by simulation with height between Mach-Zehnder arms, H=$43.6\mu\textrm{m}$(path difference $0.668\mu\textrm{m}$) was showed best characteristics. In the results of dry etching of core layer, the etching rate of core layer was above 2600${\AA}$/min, the etching ratio of SiO2 to Al mask was 30:1 and the uniformity of etching was $\pm$5%. The maximum insertion loss and the uniformity of $2\times32$ coupler were below 19.2dB, 2dB respectively.

• Economic and Environmental Geology
• /
• v.22 no.4
• /
• pp.381-393
• /
• 1989

Hydrogeological modelling was performed to evaluate groundwater flow system in Igsan Area. The study area extends over $790km^2$. The geology consists of Jurassic Daebo granite and gneissose granite and Precambrian metamorphic rocks. The capability of pumping yield is the highest in gneissose granite region among them due to comparatively thick weathered zone with thickness ranging from 10m to 25m. The Colorado State University Finite Difference Model was used for the model simulation. The model was divided into 28 rows and 31 columns with variable grid spacing. The model was calibrated under steady-state and unsteady-state conditions. In the steady-state simulation, the model results were compared with measured water table contours in September 1985 with determining hydraulic conductivities and net recharge rates during rainy season. Unsteady state simulation was done to know the aquifer response due to groundwater abstraction. The non- steady state calibration was conducted to determine the distribution and magnitudes of specific yields and discharge/recharge rates during dry season as matching water level altitudes in May 1986. The calibrated model was used to simulate water level vaiation caused by groundwater withdrawal and natural recharge from 1 October, 1985 until 30 September, 1995. The calibrated model can be used to groundwater development schemes on regional groundwater levels, but it cannot be used to simulate local groundwater level change at a specific site.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.6 no.1
• /
• pp.87-94
• /
• 1986

Under natural condition, many rivers had shallow and gently curved shape in plane. A two dimensional mathematical model of the flow was a very attractive one. The flow characteristics in bended open channels were analyzed. The mathematical model based on the mass and the momentum equation of the two-dimensional unsteady flow was developed by introducing finite difference method and the double sweep algorithm. For the purpose of the verification of this model, the modeling results were applied to the L.F.M flume and the I.I.H.R flume. The results had a good agreement with the experimental data of the flumes. The results could be more close to the experimental data by controlling Chezy Coefficients in order to reduce the effect of friction around side wall, and be studied the importance of the convective term. The water surface profile, the direction and scale of depth average mean velocity and the path of the thread of maximum velocity in bended open channels could be computed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.2
• /
• pp.66-73
• /
• 2018

A computational fluid dynamics simulation of pyrotechnic material combustion inside a cylindrical closed vessel was carried out using the Eulerian-Lagrangian method. The 5th order upwind WENO scheme and the improved delayed detached eddy turbulence model were implemented to capture shock waves. The flow structure was analyzed inside the cylindrical vessel with a pressure sensor installed at the side wall center. The analysis revealed that the pressure oscillated because of the shock wave vibration. Additionally, the simulation results with four different sensor tab depths implied that, inside the sensor tab, eddies were generated by the excessively large gap between the sensor diaphragm and the side wall. These eddies caused irregularity to the measured time-pressure curve, which is an undesirable characteristic.

• The Journal of the Petrological Society of Korea
• /
• v.8 no.1
• /
• pp.24-33
• /
• 1999

Differential Strain Analysis (DSA) was performed to examine the characteristics of microcracks for the granites from two sites, Noeunri and Gunggiri. The results of the DSA are taken every 5 MPa for the first 50 MPa, then every 10 MPa to a pressure of 100 MPa, and then every 15 MPa to a pressure of 250 MPa. Differential strain was measured on core samples in three horizontal directions, using $45^{\circ}$ rosette strain gages, and one vertical direction. The gradients of cumulative crack strain curves in one vertical direction and three horizontal directions differed from one another, indicating anisotropic crack development in the sample. The magnitude of vertical cumulative crack strain was the highest, indicating that the microcracks from the studied rock are generally developed in horizontal direction. Under the pressure of 240 Mpa, vertical cumulative crack strains for samples N-1, N-2, G-1, and G-2 were $74{\times}l0^{-6}~820{\times}l0^{-6},\; 190{\times}l0^{-6}~460{\times}l0^{-6},\; 329{\times}l0^{-6}~836{\times}l0^{-6},\; 833{\times}10^{-6}~1,592{\times}l0^{-6}$, respectively. Under the pressure of 25O MPa, volumetric crack strains for Gunggiri and Noeunri ranged from $1,804{\times}10^{-6}\; to\; 3,936{\times}10^{-6}\; and \;from,\; 1, 125{\times}10^{-6}\; to\; 1,457{\times}10^{-6}$, respectively. Therefore, the amount of microcrackes produced were more distributed in Gunggiri than Noeunri. The ratio of a maximum crack strain to a minimum crack strain was calculated to find the orientations between microcracks and the rift plane of the granites. Generally, the ratio has very high values ranging from 2.42 to 3.43, which suggests most microcracks to be intragranular cracks with the regular orientations. These results indicate that the preferred orientations of microcracks in the granites were almost parallel to the rift plane of the granites.