• Journal of Powder Materials
• /
• v.9 no.1
• /
• pp.43-49
• /
• 2002

Microstructural and mechanical characteristics of P/M 6061 Al alloy subjected to equal channel angular pressing (ECAP) were investigated. The P/M 6061 Al alloy had an intial grain size of approximately $20\mutextrm{m}$. An equiaxed ultra-fine grained structure with the mean grain size of $~50 \mutextrm{m}$ was obtained by four repetitive ECAP at 473 K. The microhardness of P/M 6061 Al alloy was drastically increased from about 40 Hv to 80 Hv by two repetitive ECAP at 373 K. However, the microhardness decreased with increasing ECAP temperature. The tensile stength of as-hot-pressed P/M 6061 Al alloy before ECAP was 95 MPa, whereas it increased to both 248 MPa after two repetitive ECAP at 373 K and 130 MPa after four repetitive ECAP at 473 K. The tensile properties of the ECAPed sample were compared with those of commercial cast 6061-O and 6061-T4 Al alloys.

• Journal of Biosystems Engineering
• /
• v.15 no.2
• /
• pp.99-109
• /
• 1990

Rough rice is subjected to a series of static and dynamic forces during mechanical harvesting, handling and processing operations. The mechanical properties such as bioyield point, compressive strength, and deformations at the bioyield point and rupture point are important engineering data needed to develop processing machines and to determine reasonable operating conditions for these machines. The objectives of this study were to determine the mechanical properties of the rough rice kernel at loading rate of 0.664 mm/min and 1.673 mm/min and at various moisture contents, and to examine the effect of the moisture content and the loading rate on these mechanical properties. The follwing results were obtained from the study. 1. Bioyield point, rupture point, bioyield strength and ultimate strength of the rough rice kernel generally decreased in magnitude with an increase in moisture content. A little larger values of these mechanical properties were obtained at the higher loading rate. The rough rice variety and the loading rate affected significantly these mechanical properties at low moisture content, but not at the higher moisture levels. 2. Bioyield point of the sample grains varied from 20 to 80 N, and rupture point varied from 45 to 130N. Bioyield point for Japonica-type rough rice was a little higher than that for Indica-type rough rice, but there were little differnces in rupture point between two types of rough rice. 3. Bioyield strength and ultimate strength of the Japonica-type rough rice varied from 10 MPa. to 39 MPa., and from 13 MPa. to 45 MPa. respectively. Those of the Indica-type rough rice varied from 12 MPa. to 42 MPa., and from 15 MPa. to 53 MPa. respectively. 4. Deformations at bioyield point and rupture point ranged from 0.18 mm/min to 0.26 mm, and from 0.28 mm to 0.53 mm respectively. These deformations decreased with an increase in moisture content up to moisture content of approximately 17% (w.b.) and increased again thereafter. 5. Regression equations were developed to predict these mechanical properties for the rough rice kernel as a function of moisture content.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.6
• /
• pp.606-611
• /
• 1999

Low dielectric Mullite/Glass composites for substrates were fabricated by mullite by synthesized from kaolin and alumina, and borosilicate glass. By the liquid-sintering, the composites were densified at low sintering temperature in air, allowing confiring with Cu, Ag, Au and Ag-Pd. Crystallization of the borosilicate glass was not occurred. The mullite/50 wt% glass composites fired between 950 and $1100^{\circ}C$ showed good properties for high-performed substrate, such as low dielectric constant (5.2~5.4, at 1MHz), low coefficient of thermal expansion (5.3~$5.7{\times}10^{-6}{\cdot}^0C^{-1}$), and bending strength of 130 MPa.

• Korean Journal of Food Science and Technology
• /
• v.39 no.5
• /
• pp.521-526
• /
• 2007

In this study, we prepared methyl cellulose (MC) and hydroxypropylated methyl cellulose (HPMC) films with polyethylene glycol (PEG) or polyphosphates as elongation enhancing materials, and with lipid layers as moisture barrier materials. We then determined their physical properties and compared the data with target physical properties such as a tensile property of 13.0 MPa, elongation of 130%, and water vapor permeability of $3.47{\times}10^{-2}ng{\cdot}m/m^2{\cdot}s{\cdot}Pa$. The PEG and polyphosphates were required for enhancing elongation, while the coating method seemed better than the emulsion method when applying the lipid layers. With respect to elongation, the MC films were better than the HPMC films.

• Environmental Engineering Research
• /
• v.23 no.2
• /
• pp.159-163
• /
• 2018

The feasibility of applying coagulation-integrated microfiltration (MF) as a pretreatment for an ultrafiltration (UF) feed in oily wastewater treatment was investigated. The effects of different coagulants on oil removal rates from wastewater were studied. The maximum oil removal rate of 82% was obtained after coagulation with 130 mg/L of polyaluminium chloride (PAC). UF flux reached $95L/(m^2{\cdot}h)$ with coagulation-integrated MF as pretreatment. This value was 2.5 times higher than that flux obtained without pretreatment. The value of UF flux increased as the transmembrane pressure (TMP) and cross-flow velocity (CFV) of the UF module increased. UF flux gradually increased when TMP and CFV exceeded 0.4 MPa and 3 m/s, respectively, because of concentration polarization and membrane fouling stabilization. Chemical oxygen demand reduction and oil removal rate reached 95.2% and 98.5%, respectively, during integrated membrane processing with a PAC concentration of 130 mg/L, TMP of 0.4 MPa, and CFV of 3 m/s for UF. In addition, sequentially cleaning the fouling membrane with NaOH and $HNO_3$ aqueous solutions caused UF flux to recover to 90%. These encouraging results suggested that the hybrid integrated membrane process-based coagulation and MF + UF are effective approaches for oily wastewater treatment.

• Elastomers and Composites
• /
• v.50 no.1
• /
• pp.30-34
• /
• 2015

Thermo-mechanical treatment process of a compressed open-cell rigid polyurethane foam (OC-RPUF), which was fabricated for the vacuum insulation panel (VIP), was studied to obtain an optimum condition for the dimensional stability by the relaxation of compressive stress. Thermo-mechanical deformation of the sample OC-RPUF was shown to occur from about $120^{\circ}C$. Yield stress of 0.36 MPa was shown at about 10% yield strain. And, densification of the foam started to occur from 75% compressive strain and could be continued up to max. 90%. Compression set of the sample restored after initial compression to 90% at room temperature was ca. 82%. Though the expansion occurred to about twice of the originally compressed thickness in case of temperature rise to $130^{\circ}C$, it could be overcome and the dimensional stability could be maintained if the constant load of 0.3 MPa was applied. As the result, a thermo-mechanical treatment process, i.e, annealing process at temperature of $130{\sim}140^{\circ}C$ for about 20 min as is the maximum compressed state at room temperature, should be required for dimensional stability as an optimum condition for the use of VIP core material.

• Journal of the Korean Institute of Gas
• /
• v.15 no.6
• /
• pp.57-62
• /
• 2011

In this study, the optimized design for 130 liter storage fuel tank with 70MPa filling pressure has been investigated using a FEM technique and Taguchi design method. The strength safety of a composite fuel tank in which is fabricated by an aluminum liner of 6061-T6 material and carbon fiber wound composite layers of T800-24K has been analyzed based on the criterion of design safety of US DOT-CFFC and Korean Standard. The FEM computed results on the stress safety of 70MPa hydrogen gas tank were compared with a criterion of a stress ratio, 2.4 of US DOT-CFFC and Korean Standard, and indicated the safety. Thus, the optimized design elements based on the Taguchi's method were recommended as an aluminum liner thickness of 6.4mm, a carbon fiber laminate thickness in hoop direction of 31mm and a carbon fiber laminate thickness in helical direction of 10.2mm, which is represented by a design model of No. 5.

• Journal of the Korean Society for Heat Treatment
• /
• v.25 no.6
• /
• pp.292-298
• /
• 2012

In this study, Cu-2.5at.%Ni-1at.%Si alloys were fabricated by horizontal continuous casting system to improve the electrical conductivity and mechanical properties of Cu-Ni-Si alloy. Withdrawing speed was changed with 50, 100, 150 and 200 mm/min for the optimum manufacturing condition. Microstructure was observed using OM, FE-SEM and TEM. Electrical conductivity was measured by 4-point probe method and mechanical properties were tested. A horizontal continuous cast thin slab had sound macro and micro structures with partly crystallized structures. Electrical resistivity decreased with increasing annealing temperature from 250 to $850^{\circ}C$, with increasing annealing temperature The maximum hardness and tensile strength were Hv 130, 610 MPa at $550^{\circ}C$, respectively. With changing withdrawing speed from 50 to 150 mm/min, hardness, tensile strength, yield strength and elongation were Hv 60-65, 210-230 MPa, 65-75 MPa and 40-50%, respectively.

• Journal of the Korean Ceramic Society
• /
• v.31 no.7
• /
• pp.703-714
• /
• 1994

Sintering and microstructure of Ce-TZP/Al2O3 composite with $\alpha$-Al2O3 matrix containing dispersed 5~50 vol% ZrO2 were discussed. Sintered density was increased with elevating forming pressure in range of 6~300 MPa and about >99.2% of theoretical density was obtained at 1$600^{\circ}C$ for 2h in case of 300 MPa of 6~300 MPa uniaxially cold-pressed compacts containing 20 vol% ZrO2. All kinds of different batch composition exhibited nearly the same shrinkage behaviour with end-point shrinkage between 20 and 24%, and had the maximum shrinkage rate (0.41~0.54%/min) around 140$0^{\circ}C$. Grain growth was occurred faster in $\alpha$-Al2O3 than in {{{{ gamma }}-Al2O3 starting matrix during sintering at 1$600^{\circ}C$. Bimodal pore size distribution of interaglomerate pores with size of 0.03~0.2 ${\mu}{\textrm}{m}$ and of interaglomerate pores with size of around 60 ${\mu}{\textrm}{m}$ was obtained in Ce-TZP/$\alpha$-Al2O3 composite sintered at 130$0^{\circ}C$. But unimodal pore size distribution with around 0.1 ${\mu}{\textrm}{m}$ was observed in Ce-TZP/{{{{ gamma }}-Al2O3 composite sintered at the same temperature. Microcracks were occurred due to the tlongrightarrowm transformation of ZrO2 on cooling process.

• Journal of Power System Engineering
• /
• v.18 no.6
• /
• pp.21-28
• /
• 2014

The studies of the spray characteristics for a CRDI engine had been advancing by many researchers, because the performance and exhaust emission were significantly affected with the spray characteristics. But most experiments of the studies would be done at low ambient pressure conditions under 2MPa. In this study, injection rates were measured with Zeuch's method at various ambient pressures to 5MPa and a constant injection pressure of 130MPa. On the same conditions, non-evaporating spray images were taken with a high speed camera and analyzed carefully with Adobe Photoshop CS3. Macroscopic spray characteristics and breakup processes in the spray could be found from the examined and analyzed data. The initial injection rate, penetration, angle, velocity and breakup of the spray were practically affected with a variation of the ambient pressure, but the injection start time and injection period were scarcely affected. As the ambient pressure was higher, the breakup of a high density droplet region in the spray was happened slowly and the main position of breakup was shifted from a front of the spray to a upstream around a nozzle. The results and techniques of spray visualization and injection rate measurement in this study would be practically effective to study a high pressure diesel spray for a CRDI.