• Applied Chemistry for Engineering
• /
• v.26 no.4
• /
• pp.439-444
• /
• 2015

Several attempts to design the best-available thermosetting road markings by using MMA to improve the durability and retroreflectivity are presented in this paper. In order to improve field applicability, the components of main materials were designed by means of reducing the hardening time lower than eight minutes. The optimum mixing ratio of thermosetting road marking was TSRM-6 composed of 15.6 wt% of MMA monomer ($Tg=105^{\circ}C$), 6.0 wt% of PMMA (MW = 70,000, $Tg=60^{\circ}C$) and 1.2 wt% of TMPTA (MW = 338, $Tg=27^{\circ}C$). Also the homogeneous mixing of all components was necessary. The use of ceramic glass beads with an optimized TSRM-6 exhibited excellent performance by achieving retroreflectivity coefficients of 431, 354 and $172mcd{\cdot}m^{-2}{\cdot}lux^{-1}$ for dry, wet and rainy test condition, respectively at two hundred thousand cycles.

• Journal of the Korean Institute of Gas
• /
• v.16 no.4
• /
• pp.32-37
• /
• 2012

The aim of this study is to evaluate the characteristics of explosion and flame velocity that can be utilized to factories where Mg-Al alloy metal powders are handled in the form of raw materials, products or by-product for similar dust explosion prevention and mitigation. Because the strength of the blast pressure is the result due to flame propagation, flame velocity in dust explosion can be utilized as a valuable information for damage prediction. An experimental investigation was carried out on the influences of content ratio of Mg-Al alloy (mean particle size distribution of 151 to 161 ${\mu}m$). And a model of flame propagation velocity based on the time to peak pressure and flame arrival time in dust explosion pressure, assuming the constant burning velocity, leads to a representation of flame velocity during dust explosion. As the results, the maximum flame velocity of Mg-Al(60:40 wt%), Mg-Al(50:50 wt%) and Mg-Al(40:60 wt%) was estimated 15.5, 18 and 15.2 m/s respectively, and also tend to change with content ratio of Mg-Al.

• Journal of Adhesion and Interface
• /
• v.15 no.4
• /
• pp.151-160
• /
• 2014

A series of terpolymers based on stearyl methacrylate (SMA), n-methyol acrylamide (n-MAM), and 2-(perfluorooctyl) ethyl acrylate (PFOEA) were synthesized by changing PFOEA contents up to 8 wt% in order to obtain optimal water-repellent properties. In addition, various contents of m-isopropenyl-${\alpha}$,${\alpha}^{\prime}$-dimethylbenzyl isocyanate (TMI) from 1 to 4 wt% were added to the above terpolymers with 4 wt% of PFOEA content. The emulsion polymerization was carried out using tridecyl alcohol (EO)7 (TDA-7) as a nonionic surfactant, alkyl dimethyl amine derivatives (ADAD) as a cationic surfactant, and 2,2'-azobis(2-amidinopropane dihydrochoride) (AAPDL) as an initiator. The synthesized copolymers were characterized by FT-IR spectroscopies, contact angle, surface energy, and water-repellency. Surface and thermal properties were analyzed by SEM, TGA, and DSC. It was found that water repellency increased with increasing the contents of PFOEA and TMI.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.2
• /
• pp.39-46
• /
• 2013

In this paper, organic solar cells(OSCs) based on bulk-heterojunction structures were fabricated by spin coating method using polymer P3HT and fullerene PCBM as a photoactive layer. The fabricated OSCs had a simple glass/ITO/PEDOT:PSS/P3HT:PCBM/Al structures. The photoactive layer of mixed P3HT:PCBM was formed with 1:1 weight ratio. The hole transport layer(HTL) was used conducting polymer PEDOT:PSS concentration with gold nanoparticles. The annealing temperature and concentration of nanoparticles in HTL were verified to improve the OSC characterization. The percentage of gold nanoparticles in HTL were 0.5 wt% and 1.0 wt%, and the surface morphology, electrical properties and absorption intensities were investigated. The devices were 0.5 wt%, and the highest 3.1% of the powder conversion efficiency(PCE), 10.2 $mA/cm^2$ of the maximum short circuit current density($J_{SC}$), 0.535V of the open circuit voltage($V_{OC}$) and 55.8% of the fill factor(F.F) could be obtained when the nanoparticle concertration was 0.5 wt%. The annealing temperature of HTL was $110^{\circ}C$, $130^{\circ}C$, $150^{\circ}C$ in vacuum oven and measured the absorption intensities, surface morphology, crystallinity and electrical properties were investigated. The best property was obtained in HTL annealed at $130^{\circ}C$ for gold nanoparticles of 0.5 wt%, showing that $J_{SC}$, $V_{OC}$, F.F and PCE were about 12.0 $mA/cm^2$, 0.525V, 64.2% and 4.0%, respectively.

• Journal of Korean Physical Therapy Science
• /
• v.19 no.4
• /
• pp.7-15
• /
• 2012

Background : The purpose of this study is to determine the effect Berg Balance Scale(BBS) evaluating frequency on the walking speed and dynamic balance control in patient with stroke. Method : sixteen patient with stroke were randomly allocated to an experimental and control group of eight patients each. For the experimental group, we performed both general physical therapy and BBS and general physical therapy only for the control group. The general physical therapy programs for the 2 group were conducted for 1 hour 1 a day, 5 times a week for 4 weeks, and BBS for the experimental group was conducted for 1 time a week. Result : A comparison of the Berg Balance Scale(BBS). Timed Up Go test(TUG) and 10 meter Walking Test(10mWT) score obtained before and after the 4-week treatment revealed statistical significant different(p<.05) for the experimental group. BBS evaluated weekly and the first day and the last day evaluated in both groups after 4 weeks of BBS assessment improved significantly were (p<.05) especially in the assessment group on a weekly basis more improvement was. BBS weekly assessment group and the first day and on the last day, a group evaluation after 4 weeks in both the change of the TUG, 10mWT was significantly improved in the evaluation group(p<.05). Conclusion : 1 time a week of the BBS assessment of with stroke patients BBS, TUG, 10mWT that can help to improve. especially on a weekly basis, more has been improved.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.375-379
• /
• 2008

In this paper, a 10N class liquid propellant rocket utilizing a dissolving reaction of hydrogen peroxide is constructed and tested. Through a series of designs, seven orifices with a diameter of 200 ${\mu}m$ and a nozzle with a neck of 2.5mm in diameter and area ratio of 2.56 were made. The platinum coated on Isolite was used for catalyst. 90wt% peroxide pressed at 20 bar by nitrogen gas was used for performance evaluation. The length of the catalyst bed and the load of platinum was taken as the parameters for this experiment. For the catalyst support length of 4cm loaded on 5wt% platinum, satisfactory $c^*$ efficiency and stable thrust was observed. The light weight body of the rocket was composed of aluminum. Rocket rose about 10m with relatively constant velocity in launching test.

• Korean Journal of Materials Research
• /
• v.21 no.4
• /
• pp.187-191
• /
• 2011

Prior austenite grain size plays an important role in the production of high strength hot-rolled steel. This study investigated the effect of Ti and C contents on the precipitates and prior austenite grain size. Steel with no Ti solutes had prior austenite grain size of about 620 ${\mu}m$. The addition of Ti ~ 0.03 wt.% and 0.11 wt.% reduced the prior austenite grain size to 180 ${\mu}m$ and 120 ${\mu}m$, respectively. The amount of Ti required to significantly decrease the prior austenite grain size was in the range of 0.03 wt.%. However, the amount of carbon required to significantly decrease the prior austenite grain size was not present from 0.04 wt.% to 0.12 wt.%. Oxides of Ti ($Ti_2O_3$) were observed as the Ti content increased to 0.03 wt.%. The specimen containing 0.11 wt.% of Ti exhibited the complex carbides of (Ti, Nb) C. The formation of Ti precipitates was critical to reduce the prior austenite grain size. Furthermore, the consistency of prior austenite grain size increased as the carbon and Ti contents increased. During the reheating process of hot-rolled steel, the most critical factor for controlling the prior austenite grain size seems to be the presence of Ti precipitates.

• Journal of the Korean Society of Physical Medicine
• /
• v.5 no.4
• /
• pp.655-666
• /
• 2010

Purpose : The examine the reliability and validity of the modified Emory Functional Ambulation Profile(mEFAP) for assessing gait function in chronic stroke patients. Methods : A total of 45 stroke patients, who had a stroke more than 6 months, participated in the study. Reliability was determined by Intra-class Correlation Coefficient($ICC_{3,1}$), including Bland and Altman method (Standard Error of Measurement: SEM, Small Real Differences: SRD). Validity was examined by correlating results to the gait ability(mEFAP, Modified Motor Assessment Scale-Gait(MMAS-G), Scandinavian Stroke Scale-Gait(SSS-G), Functional Ambulation Category(FAC), 10m Waking Test(10m WT)), and Fugl Meyer-Lower/Extremity(FM-L/E), Berg Balance Scale(BBS). Results : Inter-rater reliability for the total mEFAP was High($ICC_{2,1}$=.998), and absolute reliability were excellent (SEM: 1.75, SRD: 4.85). Subjects without assistance factor performed better on all tests than did subjects who had stroke. There were significant correlations between the mEFAP and MMAS-G, SSS-G, FAC(r=-.66~-.79), 10 m WT(r=-.86), and FM-L/E, BBS(r=-.72~-.78), indicating good validity. Increased times on the mEFAP correlated with poor performance on the gait ability, motor function of lower extremity, BBS and slow gait speeds on the 10 m WT in stroke patients. Conclusion : The mEFAP can be administered easily and comprehensively. It is a reliable gait assessment tool for patients with stroke and correlated with known of function, the mEFAP may be a clinically useful measure of ambulation.

• Korean Journal of Soil Science and Fertilizer
• /
• v.32 no.4
• /
• pp.357-364
• /
• 1999

This study measures the influence of grass cover on water use and shoot growth of apple trees growing under different soil water regimes in temperate climate conditions and evaluates monthly crop coefficients of such conditions during four months of the growing season in 1995. To do so, double pot lysimeter experiments of 3-year-old Fuji' apple (Males domestica Borkh.) trees under a transparent rain shield were designed and installed. Trees were triplicate under three soil water regimes: (A) drip-irrigation at -50 kPa of soil matric potential (IR50). (B) drip-irrigation at -80 kPa of soil matric potential (IR80), and (C) constant shallow water table at 0.45 m below the soil surface (WT45). In each treatment, two soil surface conditions were tested: the soil surface bare, and covered with turf grasses. Mean monthly water use increased with increasing soil matric potential for drip irrigation and was greatest in the WT45 treatment. Monthly crop coefficients increased linearly in time for drip-irrigated apple trees ($r^2$ values of $0.953^{***}$ for turf grass-covered system and of $0.862^{***}$ for bare surface system), while those obtained in the WT45 treatment fluctuated, Duncan's multiple range tests for shoot growth showed that grass-covered IR50 was most favorable to apple trees. while bare surface waterlogged situation was most adverse at least in part due to a lack of oxygen in the root zone. Mid-season leaf Kjeldahl-N was higher in drip-irrigated apple trees than in WT45 trees, while soil Kjeldahl-N was not different irrespective of treatments.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.31 no.2
• /
• pp.186-194
• /
• 1998

Species composition and biomass of intertidal benthic algae were studied at the coast of Yonggwang Nuclear Power Plant area and its adjacent stations over 4 seasons (October 1995-August 1996), Of 68 species identified, 7 were Cyanophyta, 12 were Chlorophyta, 14 were Phaeophyta and 35 were Rhodophyta. The largest number of algal species (44) was found at Sangnok, the northernmost station of the study area, whereas the smallest number of species (15) was found from Tongho, ca. 13 km north of the power plant site. Number of species showed highest during the spring (44) and minimum was recorded in autumn (28). Biomass per unit area showed maximum in spring ($189.5\;g\;dry\;wt{\cdot}m^{-2}$ in average) and minimum in winter ($107.9\;g\;dry\;wt{\cdot}m^{-2}$ in average). Biomass values exhibited a wide range of variation among the stations, ranging from a low of $22.0\;g\;dry\;wt{\cdot}m^{-2}$ in annual average at Tongho to a high of $295.7g\;dry\;wt{\cdot}m^{-2}$ in average at Sangnok. Dominant species in biomass were Corallina pilulifera, Sargassum thunbergii, Gymnogongrus flabelliformis and Enteromorpha compressa. There have been little variation in the dominant algal species around the power plant site during the past 10 years and also these algae appeared throughout the west coast of Korea with higher frequency.