• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.124-124
• /
• 2010

Currently, extreme ultraviolet lithography (EUVL) is being investigated for next generation lithography. EUVL is one of competitive lithographic technologies for sub-22nm fabrication of nano-scale Si devices that can possibly replace the conventional photolithography used to make today's microcircuits. Among the core EUVL technologies, mask fabrication is of considerable importance due to the use of new reflective optics having a completely different configuration compared to those of conventional photolithography. Therefore, new materials and new mask fabrication process are required for high performance EUVL mask fabrication. This study investigated the etching properties of SnO2 (Tin Oxide) as a new absorber material for EUVL binary mask. The EUVL mask structure used for etching is SnO2 (absorber layer) / Ru (capping / etch stop layer) / Mo-Si multilayer (reflective layer) / Si (substrate). Since the Ru etch stop layer should not be etched, infinitely high selectivity of SnO2 layer to Ru ESL is required. To obtain infinitely high etch selectivity and very low LER (line edge roughness) values, etch parameters of gas flow ratio, top electrode power, dc self - bias voltage (Vdc), and etch time were varied in inductively coupled Cl2/Ar plasmas. For certain process window, infinitely high etch selectivity of SnO2 to Ru ESL could be obtained by optimizing the process parameters. Etch characteristics were measured by on scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) analyses. Detailed mechanisms for ultra-high etch selectivity will be discussed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.1
• /
• pp.76-79
• /
• 2014

We report Zinc oxide (ZnO) nanorods synthesis and electrochemical luminescence (ECL) cell fabrication. The ECL cell was fabricated using the electrode of ZnO nanorods and Ru(II) complex ($Ru(bpy)_3{^{2+}}$) as a luminescence materials. The fabricated ECL cell is composed of F-doped $SnO_2$ (FTO) glass/ Ru(II)/ZnO nanorods/FTO glass. The highest intensity of the emitting light was obtained at the wavelength of ~620 nm which corresponds to dark-orange color. At a bias voltage of 3V, the measured ECL efficiencies were 5 $cd/m^2$ for cell without ZnO nanorod, 145 $cd/m^2$ for ZnO nanorods-$5{\mu}m$, 208 $cd/m^2$ for ZnO nanorods-$8{\mu}m$ and 275 $cd/m^2$ for ZnO nanorods-$10{\mu}m$, respectively. At a bias voltage of 3.5V, the use of ZnO nanorods increases ECL intensities by about 3 times compared to the typical ECL cell without the use of ZnO nanorods.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.2
• /
• pp.286-291
• /
• 1998

$SrTiO_3$[ST] thin films were fabricated on $RuO_2$bottom electrodes by RF magnetron sputtering with various $Ar/O_2$ratio in sputtering gas. As the content of oxygen increases, the leakage current of ST films measured at $10^5$ V/cm decreases from $2.0{\times}10^{-6}A/{\textrm}{cm}^2(Ar/O_2=10/0)$ to $3.8{\times}10^{-7}A/{\textrm}cm^2(Ar/O_2=5/5)$, and the dielectric constant of ST films increases from $70(Ar/O_2=10/0)$ to $190(Ar/O_2=5/5)$. The improvement of electrical properties of ST films is mainly due to the structural modification of ST films such as better crystallinity, smooth surface morphology with the increase of oxygen content in the sputtering gas.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.9
• /
• pp.423-429
• /
• 2002

RuOx thin films were fabricated by the method of liquid delivery MOCVD using Ru(C$_{8}$ $H_{13}$ $O_2$)$_3$ as the precursor and their thermal effects and conductivity were investigated. Ru films deposited at 25$0^{\circ}C$ were annealed at $650^{\circ}C$ for 1min with Ar, $N_2$ or N $H_3$ ambient. The changes of the micro-structure, the surface morphology and the electrical resistivity of the Ru films after annealing were studied. Ar gas was more effective than $N_2$ and N $H_3$ gases as an ambient gas for the post annealing of the Ru films, because of smaller resistivity and denser grains. The X-ray diffraction and X-ray photoelectron spectroscopy results indicate that the Ru $O_2$ phase and the silicidation are not observed regardless of the ambient gases. The minimum resistivity of the Ru film is found to have the value of 26.35 $\mu$Ω-cm in Ar ambient. Voids were formed at Ru/TiN interface of the Ru layer after annea1ing in $N_2$ ambient. The $N_2$ gas generated due to the oxidation of the TiN layer accumulated at the Ru/TiN interface, forming bubbles; consequently, the stacked film may peel off the Ru/TiN interface.e.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.100-100
• /
• 2009

$TiO_2$ is widely being used as a semiconductor electrode for DSSC. Anti-recombination property and surface area of $TiO_2$ give an important influence to the DSSC efficiency. In this study, $TiO_2$ electrode was fabricated on FTO using screen printing method. Various overlayers were coated on them by dip coating in solution of saturated $Ba(NO_3)_2$, $Mg(NO_3)_2$ and $N_{2}O_{6}Sr$. They reduced the recombination of electrons from photo excited state of Ru dye. The atmospheric plasma treatment was applied to both the $TiO_2$ and each overlayer coated $TiO_2$ surfaces to improve contact ability with dye. We prepared four samples, one sample has bare $TiO_2$ surfaces to improve contact ability with dye. We prepared four samples, one sample has bare $TiO_2$ electrode and the other samples consist of each overlayer coated $TiO_2$ electrodes. We used XRD, FE-SEM, J-V, IPCE and EIS in order to investigate characteristic.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.3
• /
• pp.79-86
• /
• 1992

The cause of excess current noise which appears some times in RuO$_2$ thick film chip resistors and the process to reduce such noise are investigated. We observed that too large thermal expansion coefficients of resistor paste and electrode metal paste can induce the mechanical stress and microcracks in the contact region of the two sintered materials. Such microcracks result in the reduction of conduction paths in the sintered electrode and this provokes the increase of the resistance value and the current noise. Such excessive current noise induced by microcracks could be reduced or even eliminated by using an enlarged overcoat patterns in the plating process or by adding an additional annealing process before plating.

• Journal of the Korean institute of surface engineering
• /
• v.51 no.4
• /
• pp.207-213
• /
• 2018

Not only efficiency of chlorine evolution reaction (CER) but also durability namely service life is very important property in dimensional stable anode for Ballast Water Management System (BWMS) for marine ships. Many researchers have been focused on improving efficiency of CER by controlling composition, phase and surface area for a long time, but the efforts to increase durability was relatively small. In this study, we have investigated the effect of $TiO_2$ protective interlayers on efficiency and durability of DSA electrodes. $TiO_2$ protective interlayers were prepared by thermal oxidation at 500, 600 and $700^{\circ}C$ on Ti substrate. And then the DSA electrodes consisting of $Ti/RuO_2-PdO-TiO_2$ were prepared by thermal decomposition method on $TiO_2$ interlayers. The efficiencies of CER of DSA electrodes without $TiO_2$ interlayer and with $TiO_2$ interlayer grown at 500, 600 and $700^{\circ}C$ were 94.19, 94.45, 84.60 and 76.75% respectively. On the otherhand, durabilities were 30, 55, 90 and 65 hours respectively. In terms of industrial aspect, the performance of DSA is considered high efficiency and durability which can correspond to total production of chlorine. If we considered the performance index of DSA as the product of efficiency and durability, performance indices could be recalculated as 28.26, 50.85, 76.14 and 49.89 respectively. As the thermal oxidation temperature increasing, life time were increased remarkerbly, while efficiency of CER was decreased slightly. As a result, DSA electrode with $TiO_2$ interlayer grown at $600^{\circ}C$ has shown about 2.7 times performace of original DSA electrode without $TiO_2$ interlayer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.10
• /
• pp.620-624
• /
• 2016

Ferroelectric $Pb(Zr_{0.52}Ti_{0.48})O_3$ (PZT) films were deposited on SrTiO3(100) substrate by using conductive $SrRuO_3$ films as underlayer and their structural and ferroelectric properties were investigated. PZT films were grown in (00l) orientation on well lattice-matched pseudo-cubic $SrRuO_3$ films. Thickness dependence of ferroelectric and electrical properties of PZT films was investigated. PZT film with 400 nm thickness showed a remanent polarization ($P_r$) of $29.0{\mu}C/cm^2$ and coercive field ($E_c$) of 83 kV/cm, and $P_r$ decreased and $E_c$ increased with thickness reduction. The dielectric constant for PZT films showed gradual decrease with thickness reduction. Breakdown field of PZT films did not show the thickness dependence and displayed as high value as 1 MV/cm.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1996.06a
• /
• pp.528-528
• /
• 1996

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.357.2-357.2
• /
• 2014

Ruthenium (Ru) 박막은 우수한 화학적 열적 안정성 및 높은 일함수(4.7eV) 특성으로 인해 20 nm급 이하의 차세대 DRAM capacitor의 전극 물질 및 Cu metalization을 위한 seed layer로 각광을 받고 있다. Ru박막의 나노스케일 정보전자소자로의 적용을 위해서는 두께제어가 용이하고 3D 구조에서 우수한 단차 피복 특성을 갖는 atomic layer deposition (ALD)을 이용한 박막 형성이 필수적이다. 이에 본 연구에서는 ALD 방법을 이용하여 0가의(cymene) (1,5-hexadiene) Ru (0) (C16H24Ru) 전구체를 합성, ALD 방법을 이용하여 우수한 초기성장거동을 갖는 Ru 박막을 증착 하였다. 형성된 Ru 박막의 표면 형상, 두께, 밀도를 주사전자현미경(Scanning electron microscopy)과 X-선 반사율 측정(X-ray reflectometer)으로 조사하였다. 또한 전기적 특성을 4침법(four-point-probe)으로 측정하였고, 박막의 화학적 조성과 결정성의 정보를 X-선 광전자분광법(X-ray photoelectron spectroscopy)과 X-선 회절(X-ray diffraction)을 이용하여 확인하였다.