• 한국정보처리학회논문지
• /
• 제5권10호
• /
• pp.2676-2685
• /
• 1998

본 논문에서는 파이프라인 프로세서의 분기 명령어 처리 성능 향상을 목적으로, BTB의 미스율을 줄이고 분기 예측의 정확도를 개선하기 위해 victim cache를 활용한 2-단계 BTB 구조를 제안한다. 2-단계 BTB는 기존의 BTB에 작은 크기의 victim BTB를 추가한 구조로, 적은 비용으로 BTB 미스율을 개선하고, 동적 예측(dynamic prediction)과 정적 예측 (static prediction)이 함께 사용되는 기존의 통합 분기 예측(Hybrid Branch Prediction) 구조의 예측 정확도를 높이도록 운영된다. 본 논문에서 제안된 2-단계 BTB에 의한 성능 개선을 4개 벤치마크 프로그램에 대한 trace-driven 시뮬레이션을 통해 검증한 결과, 기존의 BTB에 비해 2.5∼8.5%의 비용 증가로 BTB 미스율이 26.5% 개선되고, 기존의 gshare에 비해 64%의 비용 증가로 예측 정확도는 26.75% 개선되었다.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.279-283
• /
• 2009

Bubble jet loop heat pipe is what heat pipe operate in the horizontality. It is consist of one heating part creating bubble and one rounded U tube type radiator. This study shows whether the heat pipe operates well in the horizontality or not, and what optimized refrigerant charging rate is in the tube. But flow visualization of bubble jet heat pipe was not known. The purpose of this study is to visualize bubble jet loop heat pipe. The experiment was performed by changes of charging rate. Working fluid was R-141b. And heater of 220 V & 100 W was used. we take a photograph of flow visualization of bubble jet loop heat pipe in slow motion.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.1503-1506
• /
• 2009

Bubble jet loop heat pipe is a newly devised variation of heat pipe in which heat is effectively transported by the latent heat of evaporation and condensation as well as the heat capacity of circulating working fluid. The circulatory and oscillating motion of the working fluid becomes possible by the motion of bubble jet which is generated at a narrow circular gap. These bubbles are condensed at the condensing section. Bubble jet loop heat pipe makes it possible to carry heat long distances upward and horizontal directions. Because Its structure is a very simple and a low cost, it is available for the floor heating, vinyl house heating, the defrosting of heat pump system and home refrigerator.

• 대한기계학회논문집B
• /
• 제28권12호
• /
• pp.1475-1483
• /
• 2004

Loop thermosyphon(LTS) has many good characteristics such as low thermal resistance, no power consumption, noiseless operation and small size. To investigate the overall performance of LTS, we have performed various experiments varying three parameters: input power of the heater, working fluid(water, ethanol, FC3283) and filling ratio of the working fluid. At a combination of these parameters, temperature measurements are made at many locations of the LTS. The temperature difference between the evaporator and the condenser is used to obtain the thermal resistance. In addition, flow visualization using a high speed camera is carried out. The thermal resistance is not constant. It is lower at higher input power, which is one of the distinct merits of LTS. Flow instabilities are frequently observed when changing the working fluid, the input power and the filling ratio. The results show that the LTS can be readily put into practical use. Future practical application in electronic cooling is recommended.

• 반도체디스플레이기술학회지
• /
• 제15권2호
• /
• pp.74-80
• /
• 2016

This study presents a thermal device specially designed for thermal nanoimprint lithography equipments, which requires the capability of rapid heating and cooling, high temperature uniformity and the material strength to endure high stamping pressure. The proposal to meet these requirements is a planar-type hot plate extensible to a large area, in which long circular cartridge heaters and heat pipes are installed inside in parallel. The heat pipes are connected to the outside water cooling chamber. A hot plate made of stainless steel is fabricated with a dimension $240mm{\times}240mm{\times}20mm$. Laboratory experiments are conducted to examine the thermal performance of the hot plate. The results illustrate that the employment of heat pipes leads to a notable enhancement of temperature uniformity in the device and provides an efficient heat delivery from the hot plate to outside. It is verified that the suggested hot plate could be a feasible thermal tool for thermal nanoimprint lithography, satisfying the major design requirements.

• 한국지열·수열에너지학회논문집
• /
• 제10권2호
• /
• pp.13-18
• /
• 2014

This paper proposes an optimum pipe material (PVC vs. PE) design & selection for open loop ground heat exchangers. Heat exchange efficiency and/or workability, and the need for trench insulation were investigated by comparing EWT (cooling mode) of each system. CFD simulations for the PVC and PE pipe with the same inner diameter show similar EWT. This is because the PVC pipe has a small thickness but a low thermal conductivity as compared to the PE pipe, and thus these two properties tend to offset each other. However, a hypothetically insulated pipe led to a meaningful drop of EWT. This means pipe insulation is of importance in performance of ground heat exchangers. From analyzing climate data and system operation, it is not advantageous to insulate trench pipes due to construction difficulties and ground temperature characteristics that are seasonally varied.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 추계학술대회 논문집
• /
• pp.1710-1716
• /
• 2008

The Loop Heat Pipe (LHP) operates to pump the working fluid by means of the capillary force in a wick structure. Particularly, it is difficult to design and manufacture the evaporator consisted of a grooved container and a compensation chamber as well as the wick structure. This study is related to design and manufacture the grooved container coupled with wick structure, the properties of the wick structure such as the permeability, the porosity, and the maximum capillary pressure were measured to apply the cooling technology for Insulated Gate Bipolar Transistor (IGBT). The container of the LHP was manufactured by the electrical discharge process and the wick structure was sintered with the nickel particle by an axial-press apparatus with the pulse electronic discharge. As results, the properties of the wick were experimentally obtained about 60% of the porosity, 35kPa of the maximum capillary force and $1.53{\times}10-13m2$ of the permeability.

• 한국항공우주학회지
• /
• 제42권5호
• /
• pp.430-436
• /
• 2014

본 논문에서 제안한 우주기반기술 검증용 극초소형 위성의 명칭은 STEP Cube Lab.(Cube Laboratory for Space Technology Experimental Project)이며, 주요임무는 가변 방사율 열제어기, 형상기억합금 진동 절연기, 진동형 히트파이프, MEMS 기반 고체 추력기와 같이 국내 산학연에서 기 수행된 우주핵심기술을 발굴 및 탑재하여 궤도검증을 실시하는 것이다. 또한, 배열형 집광렌즈가 적용된 고효율 집광형 태양전력시스템과 열선절단방식이 적용되어 높은 체결력과 적용방법에 따라 복수구조물의 구속 및 분리가 가능한 무충격 구속분리장치를 주요 탑재체로 개발하여 궤도 검증을 실시예정이다. 본 논문에서는 상기 탑재체의 궤도 검증을 임무목적으로 하는 STEP Cube Lab.의 체계 및 부체계 개념설계를 통해 임무의 구현 가능성을 검토하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제37권4호
• /
• pp.324-331
• /
• 2013

이중진공관형 집열기는 진공기술을 이용하여 흡수면에서 대류열손실을 줄일 수 있으며, 비교적 적은 온도차에서도 열수송능력과 열응답성이 빠른 이점이 있어 유용한 기기로 연구가 지속적으로 진행되고 있다. 본 연구에서는 태양열 집열기와 냉동기가 조합한 성능실험장치를 이용하여 태양열의 일사량, 유체온도의 제어조건에 따른 집열기의 동적 열성능을 파악하고, 이에 따른 항온조를 이용한 유체의 일정한 온도범위에서 냉동성능을 동시에 측정하여 열역학적 특성을 고찰하였다. 그 결과로서 집열효율의 관계식을 도출하였으며, 항온조의 출구온도 $18^{\circ}C$와 $22^{\circ}C$에서 집열기의 출구온도 $25^{\circ}C$로 설정하였을 때 항온조의 출구온도 $22^{\circ}C$ 경우가 외기온도 및 일사량이 증가함으로써 빠른 열전달특성을 보여 평균집열효율이 상승됨을 보였다. 또한 항온조의 출구온도 $18^{\circ}C$에서 냉동기의 성능계수는 6.2~7.1 정도의 결과를 얻게 되었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권6호
• /
• pp.737-743
• /
• 2014

본 논문에서는 기존 1kW 할로겐 탐조등을 대체하기 위한 고출력 LED 탐조등에 관하여 기술하였다. 설계사양은 KDS 6230-1046-1과 KS V 8469를 기준으로 하였으며, 요구 광도 800,000cd를 만족시키기 위하여 지향각 $6^{\circ}$의 렌즈를 사용하였다. 시제작 LED 탐조등의 방열은 공랭식으로써 팬이나 히트파이프를 사용하지 않았다. 시험결과, 시제작 LED 탐조등의 소비전력은 148W로 1kW 할로겐 탐조등에 비해 85% 절감되었으며, 중심광도는 945,000cd로써 KS V 8469를 만족하였다. 광효율은 기존 탐조등보다 4.7배 향상되었으며, 지향각, 색온도 및 연색성은 각각 $5.4^{\circ}$, 5,500K, 70이었다. LED 탐조등의 외함 온도는 $60^{\circ}C$ 이하이고, SMPS 주변 온도는 $50^{\circ}C$ 이하로 IEC 60092-306을 만족하였다.