• Journal of computational fluids engineering
• /
• v.8 no.3
• /
• pp.32-40
• /
• 2003

CFD analyses of the three-dimensional turbulent flow in the impeller and diffuser of an axial flow pump including suction and discharge parts are presented and compared with experimental data. The purpose of the current study is to validate the CFD method for the performance analysis of the main coolant pump for SMART and to investigate the effect of suction and discharge shapes on the pump performance. To generate a performance curve, not only the design point but also the off-design points were computed. The results were compared with available experimental data in terms of head generated. At the design point, the analysis accurately predicts the experimental head value. In the range of the higher flow rates, the results are also in very good agreement with the experimental data, in magnitude but also in terms of slope of variation. For lower flow rates, the results shows that the analysis considering the suction and discharge well describe the typical S-shape performance curve of the axial pump.

• Journal of computational fluids engineering
• /
• v.17 no.2
• /
• pp.100-106
• /
• 2012

Ice accretion on the surface of aircraft in flight can adversely affect the safety of aircraft. In particular, it can cause degradation of critical aircraft performances such as maximum lift coefficient and total pressure recovery factor in engine air intake. In this study, computational prediction of ice accretion around a rotorcraft air intake is conducted in order to identify the impingement region with high droplet collection efficiency. Then the amount of ice accretion on the air intake, which is essential in determining the required power of ice protection system, is calculated. Finally, the effect of icing wind tunnel size is investigated in order to check the compatibility with the real in-flight test environment.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.465-468
• /
• 2011

Ice accretion on aircraft surface can greatly deteriorate the safety of aircraft. In particular, it can be a cause of impediment for aircraft performances such as aerodynamic characteristics, control, and engine. Numerical simulation of icing accretion based on the state-of-art CFD techniques can be alternative to expensive icing wind tunnel test or flight test. In this study, icing conditions are defined in order to predict the ice accretions around the air intake of aircraft. Then the range and amount of ice accretion on the intake in icing wind tunnel were investigated In addition, a study on the size effect of icing wind tunnel was conducted in order to check the compatibility with the real in-flight test environment.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.522-525
• /
• 2008

A vacuum cleaner is the widely used home equipment. However, it has a trouble with too much power consumption. Most losses occur at the centrifugal fan. To remedy this trouble the investigation of motor, which is the main component of vacuum cleaner, is required. The flow characteristics around the high-speed rotating centrifugal fan which is influenced by the very low inlet pressure is quite different from a commonly used fan. Hence it is quite difficult to analyze the flow by the experimental means or by the numerical simulation. In this research, it is aimed to improve the air-suction performance of a vacuum cleaner through the flow analysis around a motor. The efficiency of the centrifugal fan is affected by blade shape, blade number, blade pitch, etc. The influence of the shape of impeller on the flow is investigated in this study. The flow around the centrifugal fan is simulated by applying the moving mesh. To verify the validity of the computation results, the air flow rate and the pressure field to the cleaner is compared with the experimental data. All simulations are performed by using commercial code SC/Tetra. The calculated results show good agreement with the experimental ones and it is believed to be promising to use computational simulation in the improvement of the vacuum cleaner performance.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.1
• /
• pp.81-86
• /
• 2015

This paper presents a disposable passive suction pump that uses the restoring force of an elastomeric chamber for liquid transportation in a microfluidic system. The proposed suction pump can be operated by finger pressure without any peripheral equipment. To adjust the generated suction pressure, five different displacements of the suction chamber ceiling, two different chamber shapes, and five different elastic moduli of the elastomer were considered. For a cylindrical chamber with a 5 mm height and 5 mm radius, the generated suction pressure and flow rate increased almost linearly up to about 31 kPa and $160.8{\mu}L/min$, respectively, depending on the chamber deformation. A maximum suction pressure of $42.9{\pm}0.7kPa$ was obtained for a hemispherical chamber with a 2.1 mm height and 5 mm radius.

• The KSFM Journal of Fluid Machinery
• /
• v.18 no.1
• /
• pp.65-71
• /
• 2015

The purpose of this study is to investigate cavitating flow of the multistage centrifugal pump. Cavitation is observed in the impeller leading edge and trailing edge of the suction area. Head coefficients are measured under different flow operating conditions. The Rayleigh-Plesset cavitation model is adapted to predict the occurrence of cavitation in the pump. The two-phase gas-liquid homogeneous CFD method is used to analyze the centrifugal pump performances with two equation transport turbulence model. The simulations are carried out with three different flow coefficients such as 0.103, 0.128 and 0.154. The occurrence of cavitation described according to water vapor volume fraction. The head versus NPSH (Net Positive Suction Head) also measured using different flow coefficients. Development of cavitation in the centrifugal pump impellerI is discussed. It is showed that the simulation represents the head drop about 3%.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1201-1207
• /
• 2008

Numerical analysis information will be very useful to improve fluid system. General information about an internal gas flow is presented by numerical analysis approach. Relating with hydrogen compressing system, which have an important role in hydrogen energy utilization, this should be a useful tool to observe the flow quickly and clearly. Flow characteristic analysis, including pressure and turbulence kinetic energy distribution of hydrogen gas coming to the cylinder of a reciprocating compressor are presented in this paper. Suction-passage model is designed based on real model of hydrogen compressor. Pressure boundary conditions are applied considering the real condition of operating system. The result shows pressure and turbulence kinetic energy are not distributed uniformly along the passage of the Hydrogen system. Path line or particles tracks help to demonstrate flow characteristics inside the passage. The existence of vortices and flow direction can be precisely predicted. Based on this result, the design improvement, such as reducing the varying flow parameters and flow reorientation should be done. Consequently, development of the better hydrogen compressing system will be achieved.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.11 s.254
• /
• pp.1131-1138
• /
• 2006

Aerodynamic shape design of a partial admission turbine using CFD has been performed. Two step approaches are adopted in this study. Firstly, two-dimensional blade shape is optimized using CFD and genetic algorithm. Initially, the turbine cascade shape is represented by four design parameters. By controlling the design parameters as variables, the non-gradient search is analyzed for obtaining the maximum efficiency. The final two-dimensional blade proved to have a more blade power than the initial blade. Secondly, the three-dimensional CFD analysis including the nozzle, rotor and stator has been conducted. To avoid a heavy computational load due to an unsteady calculation, the frozen rotor method is implemented in steady calculation. The frozen rotor method can detect a variation of the flow-field dependent upon the blade's circumferential position relative to the nozzle. It gives a better idea of wake loss mechanism starting from the lip of the nozzle than the mixing plane concept. Finally, the combination of two and three dimensional design method of the partial admission turbine in this study has proven to be a robust tool in development phase.

• Journal of the Korean Society of Visualization
• /
• v.17 no.2
• /
• pp.73-82
• /
• 2019

The subsurface vortex - which occurs inside the cylindrical sump - was visualized through Computational Fluid Dynamics (CFD) and experiment. The analysis of subsurface vortex inside the cylindrical sump was already carried out using CFD techniques by the first author. To understand the subsurface vortex more clearly, an experimental analysis was carried out with a 1/5th scale model; and the flow rate was calculated according to the similarity law. The experimental results of vortex visualization matches well with the CFD results. The surface roughness model and Anti Vortex Device (AVD) model have been investigated to control the subsurface vortex. For the case of average surface roughness of 1mm and 5mm, the subsurface vortex appears and the vorticity is higher when compared to that of a smooth surface condition. However, for the AVD model, the subsurface vortex is completely removed and the internal flow is stabilized.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.297-305
• /
• 2006

In this paper, numerical analyses of the flow within turbine for geometric conditions such as nozzle shape, length of axial clearance, and chamfer angle of leading edge of blade have been performed to investigate the partial admission supersonic turbine losses. Firstly, flow's bending occurred at axial clearance is depended on nozzle shape. Next, the chamfer angle of leading edge affects the strength of shock generated at the leading edge. Finally the expansion and mixsing of the flow within axial clearance are largely depended upon the length of axial clearance. Therefore it is found that aerodynamic losses of turbine is affected by nozzle shape and chamfer angel and that partial admission losses is depended on nozzle shape and the length of axial clearance.