• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.94-97
• /
• 2003

The effect of pressure perturbation in the ramjet engine on the characteristics of the inlet is studied via numerical simulation. The frequency and amplitude of the pressure perturbation are assumed to be 500Hz and 20% of the exit back pressure, respectively. The simulation shows the characteristics of the normal shock in the inlet according to the pressure perturbations. The relation between the captured mass flow rate and downstream pressure perturbation is studied. The mass flow rate decreases when the downstream pressure perturbation starts.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.563-564
• /
• 2010

A Numerical analysis of preventing pressure oscillation for the supersonic inlet of IRR at the boosting mode was conducted in this study. To reduce the fluctuation of pressure, the supersonic inlet was equipped with annular slit. By decreasing the entrained air mass, the amplitude of fluctuation and maximum pressure at the inlet were decreased while the frequency was increased. In case, the optimal trade-off value is obtained between frequency and amplitude, it is expected that the pressure oscillation declining method using the slit will be helpful in various boosting and transition mode problem for IRR.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2002.04a
• /
• pp.59-59
• /
• 2002

램제트 추진기관은 압축과정을 별도의 부품 없이 형상에 의해서 감속하여 연소 압력비를 얻는다. 따라서 구동 마하수와 형상에 의해 흡입과정의 압축 효율이 결정된다. 설계점은 충분한 유량을 확보 할 수 있는 유량과 충격파 각을 조절하여 전압력 손실을 줄이도록 고려되어야 한다. 또한 연소가 일어나면 연소실 압력이 배압으로 작용하고 비행시에 받음각은 변하므로 이에 따른 성능 분석도 고려 되어야 할 사항이다. 본 연구는 국내에서 실험한 형상에 대해 수치계산을 수행하여 코드의 검증과 아울러 램제트 유동장의 수치적 시뮬레이션도 설계단계에서 하나의 도구로 이용할 수 있음을 보여준다. 실험에서는 배압 조건을 얻기 위해 유동 블록키지를 유로 내에 두어 상응하는 배압을 얻었지만 본 계산에서는 압력 경계조건을 직접 사용하였다. 유동이 비정상 특성을 가지므로 시간 정확도를 이차로 가지도록 이중시간 전진법을 사용하였다. 사용한 압력비는 충격파가 카울 끝에 닿는 임계상태에 가까운 12, 13, 14에 대해 계산을 수행하였고 부스터모드로 흡입구 끝이 막혀 있다가 램제트 모드로 바뀌어 연소실 압력이 위의 압력비라고 가정할 때의 비정상 천이 과정을 계산해 보았다. 본 계산은 흡입구 부분만을 떼어놓고 적절한 가정 하에 수행되었지만 연소실 내부도 비정상 특성을 가지므로 흡입구와 연소실을 동시에 같이 계산해야한다. 추후에 전체적인 계산을 진행하기 위한 전 단계로 흡입구 계산만을 수행하여 실험과 잘 일치하는 계산 결과를 얻었고 전체 계산을 위한 연구는 진행 중에 있다.

• Journal of Energy Engineering
• /
• v.9 no.2
• /
• pp.89-94
• /
• 2000

양흡입 펌프 회전차 내부 유동특성을 수치적으로 고찰하였다. 수치계산은 설계점과 2개의 탈설계점에서 이루어졌으며, Patankar에 의해 제시된 SIMPLE 알고리즘을 이용하였다. 설계점에서는 양 회전차 채널 내부에서 대칭 형상을 갖는 이차유동 특성을 발견하였지만, 탈설계점에서는 비대칭 유동특성을 발견하였다. 수치해석 결과로는 유량감소에 따라 양흡입 펌프 회전차 채널내부의 이차유동 특성이 달라진다는 사실을 고찰하였다. 또한 양흡입 펌프 회전차 단면에는 모퉁이 와류가 존재함을 알 수 있었다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.1
• /
• pp.17-25
• /
• 2019

An intake of Aircraft becomes S-shaped geometry due to spatial limitation or procuring survivability. But curvature of the S-shaped geometry makes secondary flow or flow separation which is the cause of non-uniform pressure distribution. In this study, boundary layer suction is applied to RAE M 2129 S-Duct by attaching sub duct. Design variable is suction location and angle. A mass flow rate drawn out by suction at the sub duct outlet is constant over every model. A grid dependency test was conducted to verify validity of computation. The comparison among the CFD (Computation Fluid Dynamics), ARA experimental result, and ARA computation result of non-dimensional pressure distribution on the Port side and Starboard Side confirmed the validity of CFD. In this study, Distortion Coefficient was used for evaluating aerodynamic performance of S-Duct. The analysis, which was about flow separation, vortex, mass flow rate distribution, and pressure distribution were also investigated. Maximum 26.14% reduction in Distortion Coefficient was verified.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.992-995
• /
• 2011

A study on the performance design schemes of the supersonic air intakes applied to the supersonic air-breathing propulsion system(Ramjet/Scramjet) was conducted and for two kinds of air intakes, the preliminary configuration designs and the performance analysis models were established. For axisymmetric conical air intake and two dimensional rectangular air intake, the performance effects were assessed according to compression angles and shock wave numbers.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.3
• /
• pp.38-48
• /
• 2005

For the development of Scramjet engine technology, intake designing processes are investigated. The basic geometry is determined by the inviuld relation such as shock wave relations and geometric relations. Furthermore, bleed duct is installed for preventing boundary layer development and shock wave impingement. Performance of the designed intake is validated by numerical analysis. As a result, double- wedge intake showed better characteristics in total pressure recovery than single-wedge intake.

• Aerospace Engineering and Technology
• /
• v.10 no.1
• /
• pp.122-128
• /
• 2011

A series of water tests of a Lox pump for liquid rocket engines are performed at a room temperature. According to the hydraulic test results, the head coefficient is slightly decreased when the rotational speed of the pump is increased. However the efficiency is high at the high-speed test. Also, according to the cavitation test results, the cavitation performance of the pump is found to be decreased when the flow ratio is less than 92%. Furthermore, the vibration characteristic is analyzed using measured high frequency data.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.9
• /
• pp.2195-2201
• /
• 2009

This paper considers the influence of suction-line heat exchangers on the efficiency of a refrigeration cycle using hydrocarbon refrigerants such as R290, R600a and R1270. These suction-line heat exchangers can, in some cases, yield improved system performance while in other cases they degrade system performance. A steady state mathematical model is used to analyze the performance characteristics of refrigeration cycle with suction-line heat exchanger. The influence of operating conditions, such as the mass flowrate of hydrocarbon refrigerants, inner diameter tube and length of suction-line heat exchanger, to the performance of the cycle is also analyzed in the paper. Results showed that the mass flowrate of hydrocarbon refrigerants, inner diameter tube and length of suction-line heat exchanger, and effectiveness have an effect on the cooling capacity, compressor work and RCI(Relative Capacity Index) of this system. With a thorough grasp of these effect, it is necessary to design the compression refrigeration cycle of hydrocarbon refrigerants using suction-line heat exchanger.

• The KSFM Journal of Fluid Machinery
• /
• v.12 no.6
• /
• pp.13-17
• /
• 2009

Ejector is an equipment devised for making use of the low pressure occurring from the fast fluid injection and it is a transportation equipment which can obtain vacuum using the kinetic energy of the fluid. This ejector system is, nowadays, widely used for construction machinery, heavy equipments, the cooling and ventilation of electronic devices and for the various fluid transportation and pumps. In this study, it is attempted to perform a numerical analysis and an experiment to find out the characteristics of fluid quantity, velocity and the pressure distribution of the induction pipe by changing the length and the radius ratio of the nozzle of ejector. From the results, it is investigated that the distributions of velocity and pressure of induction pipe attached are changing with the length and the radius ratio of the nozzle. In addition, it is shown that for the small and large ejector, the efficiency is the maximum when the length of the nozzle arrived to the neck of the ejector, however, if it is installed at below or above the neck the efficiency is rather decreased.