• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.2
• /
• pp.99-106
• /
• 2019

A wall-frame structure resists horizontal load by the interaction between the flexural mode of the shear wall and the shear mode of the frame, which implies that the frame deflects only by reverse bending of the columns and girders, and that the columns are axially rigid. However, as the height of frame increases the shear mode of frame changes to flexural mode, which is due to the extension and shortening of the columns. An approximate hand method for estimating horizontal deflection and member forces in high-rise shear wall-frame structures subjected to horizontal loading is presented. The method is developed from the continuous medium theory for coupled walls and expressed in non-dimensional structural parameters. It accounts for bending deformations in all individual members as well as axial deformations in the columns. The deformations calculated from the presented approximate method and matrix analysis by computer program are compared. The presented approximate method is more accurate for the taller structures.

• Journal of the Korea Concrete Institute
• /
• v.14 no.6
• /
• pp.934-941
• /
• 2002

It is important to consider the effect of member size when estimating the ultimate strength of a concrete flexural member because the strength always decreases with an increase of member size. In this study, the size effect of a reinforced concrete (RC) beam was experimentally investigated. For this purpose, a series of beam specimens subjected to four-point loading were tested. More specifically, three different effective depth (d$\approx$15, 30, and 60 cm) reinforced concrete beams were tested to investigate the size effect. The shear-span to depth ratio (a/d=3) and thickness (20 cm) of the specimens were kept constant where the size effect in out-of-plane direction is not considered. The test results are curve fitted using least square method (LSM) to obtain parameters for the modified size effect law (MSEL). The analysis results show that the flexural compressive strength and the ultimate strain decrease as the specimen size increases. In the future study, since $\beta_1$ value suggested by design code and ultimate strain change with specimen size variation, a more detailed analysis should be performed. Finally, parameters for MSEL are also suggested.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.4A
• /
• pp.383-389
• /
• 2010

The concrete structural design provisions in Korea are based on ultimate strength design. Up to service load stage, it is assumed a linear stress-strain relation, but there is no stress-strain relationship for a concrete material from service load stage to limat state. According to the current provisions, an independent method is provided for the each calculation of deflection and crack width. In EC2 provisions based on limit state design, however, a stress-strain relationship of concrete is provided. Thereby, it is able to calculate a strength as well as a deflection directly from concrete stress-strain relationship. In this paper the moment-curvature relationship is directly calculated from a material law using equilibrium and compatibility conditions. Then strength and deflection are formulated. These results are compared with the values from the current provisions in Korea. From the results, the deflection based on a moment-curvature relationship is well agreed with experimental results and it is appeared that the deflection after the yielding of steel is also possible.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.1
• /
• pp.35-42
• /
• 2015

Injection molding is a high efficient manufacturing technology for producing plastic parts. On the other hand, the warpage of molded plastic parts is an ubiquitous problem in the injection molding process. The main objective of this study was to minimize the amount of warpage occurring in the injection molding process of a hopper of ATDPS made of crystalline polymer (PP) instead of amorphous polymer (ABS). The moldflow CAE simulation was conducted for the molding process of the hopper to clarify the injection moldability, shear rate, shear stress, warpage by changing the gate shape and the number of ribs installed on the top of the hopper flange. The wide gate shape of runner system and multiple rib installation were found to be useful for minimizing the warpage of the hopper. The validity of the CAE simulations was supported by the injection molding experiment for the optimized design case.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.6A
• /
• pp.513-523
• /
• 2010

For continuous I-girder bridges, a large negative bending moment is generated near pier region so that plastic hinge is first formed at this point. Then, the bending moment is redistributed when the I-girder has enough flexural ductility (or rotational capacity). However, for I-girder with high strength steel, it is known that the flexural ductility is considerably decreased by increasing the yield strength of material. Thus, it is necessary to conduct a study for guaranteeing proper flexural ductility of I-girder with high-strength steel. In this study, the evaluation of flexural ductility of negative moment region of I-girder with high strength steel where yield stress of steel is 680 MPa is presented based on the results of finite element analysis and experiment. From the results, it is found that the flexural ductility of the I-girder is significantly reduced due to the increase of elastic deformation and the decrease of plastic deformation ability of the material when the yield strength increases. In this study, the method to improve the flexural ductility of I-girder with high strength steel is proposed by an unequal installation of cross beam and an optimal position of cross beam is also suggested. Finally, the effects of the unequal installation of cross beam on the flexural ductility are discussed based on the experimental results.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.23 no.5
• /
• pp.551-557
• /
• 2010

The purpose of this study is to estimate experimentally the flexural behavior, capacity and validity of existing regulation of net tensile strain in lightweight concrete beams and polymer modified lightweight concrete beams. One normal weight concrete beam and four lightweight concrete beams, three polymer modified lightweight concrete beams were constructed as same figure and attempted to evaluate the difference of strength and ductility in specimens of different net tensile strain in extreme tension steel. Test results are indicated in terms of load-deflection behavior and ductility index. As the value of net tensile strain increased, the flexural strength and stiffness of specimen decreased but ductility index increased in both of lightweight concrete beams and polymer modified lightweight concrete beams. It is considered that to achieve similar ductility index of normal weight concrete, net tensile strain in extreme tension steel should exceed 0.005 for lightweight concrete beam and polymer modified lightweight concrete beam.

• Journal of the Korea Concrete Institute
• /
• v.22 no.6
• /
• pp.825-832
• /
• 2010

Although a critical section reaches its flexural strength in reinforced concrete structures, the structure does not always fail because moment redistribution occurs during the formation of plastic hinges. Inelastic deformation in a plastic hinge region results in plastic rotation. A plastic hinge mainly depends on material characteristics. In this study, a plastic hinge length and plastic rotation are evaluated using the flexural curvature distribution which is derived from the material models given in Eurocode 2. The influence on plastic capacity the limit values of the material model used, that is, ultimate strain of concrete and steel and hardening ratio of steel(k), are investigated. As results, it is appeared that a large ultimate strain of concrete and steel is resulting in large plastic capactiy and also as a hardening ratio of steel increases, the plastic rotation increases significantly. Therefore, a careful attention would be paid to determine the limit values of material characteristics in the RC structures.

• Magazine of the Korea Concrete Institute
• /
• v.2 no.2
• /
• pp.73-80
• /
• 1990

The current analytical techniques for R/C elements under severe dynamic repeated loads, like earth¬quake or impact, have two major problems; one is that the effects of strain rate are not considered and the other one is the current analytical model was developed based on flexural behavior only. This study develops computer software that can idealize the flexural and shear behavior of R/C elements using several parameters and also can consider the effects of strain rate. The analytical results using the developed technique were compared with serveral experimental results and they were generally satisfied.

• Computational Structural Engineering
• /
• v.7 no.2
• /
• pp.11-15
• /
• 1994

본 고에서는 축대칭회전 Shell을 해석모델로 선정하여 주로 Shell의 휨 강성이 구조체의 거동에 미치는 영향에 대하여 검토하였다. 어떠한 구조형식이든 외력의 작용하에서 발생되는 응력이 축방향력 뿐이라는 것은 상당히 합리적이고 역학적으로도 명쾌한 동시에, 실제 설계상 이상적인 판단기준을 부여하지만, 실제로는 필히 휨상태를 수반하게 된다. 이러한 휨상태는 구성요소의 휨강성에 크게 의존하고 있고, 구조체에 어느정도의 휨강성을 부여하므로써 작용하중에 대한 저항능력의 증가, 변형 및 응력의 저감에 효과적이라는 것을 알 수 있다. 본 고에서는 등방성 Shell에 대한 선형 해석결과만을 게재하였으나, 이러한 성상은 여러가지 영향인자(지지조건, 하중상태 등)에 따라 아주 상이하게 나타나기 때문에 세심한 고찰이 필요하다고 할 수 있다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.8 no.4
• /
• pp.1-10
• /
• 2004

The purpose of this study is to investigate the flexural behavior of square concrete filled carbon tube (CFCT) columns subjected to constant axial load with the cyclic lateral load. Two parameters, wnding angle and thickness of tube, were chosen to evaluate the flexural capacity and behavior of rectangular CFCT columns. Selected two parameters were considered simultaneously in order to evaluate the flexural behavior of a rectangular CFCT columns more precisely. Flexural strength, deformation capacity, ductility and energy dissipation capacity of rectangular CFCT columns were evaluated by calculating the area of load-displacement envelope curves and load-dispalcement hysteresis curves obtained from experiment. Also, the ductile capacity obtained from experiment was compared to that of reinforced masonry wall for the comparison of existing structural element.