• Journal of Korean Society of Steel Construction
• /
• v.23 no.2
• /
• pp.169-177
• /
• 2011

This paper presents the results of the systematic finite element analysis of the in-plane bending moment of T-joints subjected to cyclic loadings. T-joints were fabricated using high-strength, circular, hollow sections. Three-dimensional, nonlinear finite element models of the welded T-joints were constructed to investigate the strength, rotational-stiffness characteristics, and failure modes. A wide scope of structural behaviors explain the influence of the joint geometric parameters, such as the chord and brace wall slenderness ratios and the ratio of the brace to the chord diameter, as well as the yield strength ratios and compressive-chord-stress effects on the ultimate in-plane bending moment capacity of the T-joint.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.4
• /
• pp.38-47
• /
• 2013

For the joint connection of the precast steel grid composite decks, the prefabricated joint which is composed of concrete shear key and high-tension bolts was already proposed. In this study, for the purpose of increasing the bending stiffness and bending strength of the proposed prefabricated joint section details of the proposed joint are modified, and through experimental tests the bending performance, such as stiffness and strength of a modified joint, is compared with those of the proposed joint. Test and analysis results show that the shear cracks in the concrete shear key are clearly reduced by the strengthening of the shear key using shear studs and additional rebars. According to analysis results of the moment-curvature relationship, bending stiffness of the modified joint is about 47% greater than the stiffness of the proposed joint. Furthermore, the modified joint has about 32% greater bending strength than the proposed joint. Compared to specimens without the joint the modified joint has same or slightly higher bending strength, but about 37% lower bending stiffness.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.3
• /
• pp.211-219
• /
• 2009

The purpose of the study described in this paper was to experimentally investigate branch squared T joints with cold formed hollow structural sections under the in plane moment in a Vierendeel Truss. The branch in the T joints was welded to the upper flange of the chord. The main experimental parameters were the ratio of the width to the thickness of the chord ($2{\gamma}$), with ${16.7{\leq}2{\gamma}{\leq}33.3}$, and the width ratio of the branch to the chord ($\beta$), with ${0.40{\leq}{\beta}{\leq}0.71}$. Nine specimens were tested and manufactured in joints under the in plane bending moment. Based on the results of the test, the in plane moment strength of the branch squared T joints was determined according to the bending deformation of the chord flange yielding, regardless of the ratio of the width to the thickness of the chord and the ratio of the width of the branch to the width of the chord. Also, the in plane moment strength of the branch squared T joints in the hollow structural sections can be defined as 1.5 times the moment load at M1%B the strength of the joints that governed the serviceability in the control group. Finally, the experimental results with the branch squared T joints show that the in lane moment strength of the joint increased as $2{\gamma}$ decreased and $\beta$ increased.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.6A
• /
• pp.513-523
• /
• 2010

For continuous I-girder bridges, a large negative bending moment is generated near pier region so that plastic hinge is first formed at this point. Then, the bending moment is redistributed when the I-girder has enough flexural ductility (or rotational capacity). However, for I-girder with high strength steel, it is known that the flexural ductility is considerably decreased by increasing the yield strength of material. Thus, it is necessary to conduct a study for guaranteeing proper flexural ductility of I-girder with high-strength steel. In this study, the evaluation of flexural ductility of negative moment region of I-girder with high strength steel where yield stress of steel is 680 MPa is presented based on the results of finite element analysis and experiment. From the results, it is found that the flexural ductility of the I-girder is significantly reduced due to the increase of elastic deformation and the decrease of plastic deformation ability of the material when the yield strength increases. In this study, the method to improve the flexural ductility of I-girder with high strength steel is proposed by an unequal installation of cross beam and an optimal position of cross beam is also suggested. Finally, the effects of the unequal installation of cross beam on the flexural ductility are discussed based on the experimental results.

• Journal of the Korean GEO-environmental Society
• /
• v.2 no.4
• /
• pp.15-27
• /
• 2001

This paper proposes the force equations(thrust, moment) of corrugated steel culverts through the finite element method. The conditions for maximum thrust and maximum moment are determined from the analysis of soil-structure interaction during the three construction stages, such as backfill to the crown, backfill to the soil cover, and live loads. The proposed form of thrust and moment equations are deduced from the analysis of behaviour and the application of Castigliano's second theorem for the semi-arch structure. Finally, the coefficients used in the proposed equations are determined from a large number of analysis for the various geometries and the soil-structure relative stiffness under the conditions of maximum thrust and maximum moment.

• Journal of the Korea Concrete Institute
• /
• v.14 no.6
• /
• pp.910-921
• /
• 2002

For the prediction of shear behavior of reinforced concrete beams, this paper proposed Transformation Angle Truss Model (TATM) considered bending moment effect. Shear stress-strain relationship obtained from the TATM was agreed well with test results conducted by this study Further, shear strength obtained from the TATM was compared to the experimentally observed results of 170 reinforced concrete beams which had various shear span ratios shapes of support and shapes of cross section. The shear strength of reinforced concrete beams obtained from test was better predicted by the TATM with 0.96 in average and 11.9％ in coefficient of variation than by other truss models. And the ratio of experimental results to theoretical results obtained from the TATM was almost constant regardless of the η and a/d.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.2 no.3
• /
• pp.15-22
• /
• 1982

This paper presents analytic bending moment solution and resonance diagrams for a uniform beam of infinite length subjected to anaxial force and moving transverse load. Solutions are obtained that are time invariant in a coordinate system moving with the load velocity. The supporting foundation includes damping effects. The influences of the axial force, damping coefficient and load velocity on the beam response are studied. The limiting case of no damping and critial damping are also investigated. The profiles of the mement of the beam is shown graphically for several values of the load speed, the axial force and damping parameters.

• 한국방재학회:학술대회논문집
• /
• 2010.02a
• /
• pp.84.2-84.2
• /
• 2010

본 연구는 소수주거더 교량에 적용된 I-거더에 고강도 강재인 HSB800 강재를 사용하였을 때, 휨 연성 R값을 이용하여 AASHTO LRFD(2007)의 조밀단면기준에 대한 경향성에 대해 수치해석적으로 수행되었다. 복부판 세장비, 플랜지 세장비, 비지지 길이를 변수로 하여 휨 연성 R값을 구해서 기존의 AASHTO LRFD(2007)의 조밀단면기준에 적용하여 휨 연성에 대한 경향성을 나타내었다.

• Journal of Korean Society of Steel Construction
• /
• v.22 no.6
• /
• pp.533-541
• /
• 2010

H-shaped beams, which are constructed between columns, are used widely as slaves in steel structures. The bending moments that occur on both ends of an H-shaped beam, however, are about twice the bending moment that occurs at the center of the H-shaped beam. Because such beam is designed with maximum bending moment, it is deeper and has smaller spaces. To improve these features, if both ends of an H-shaped beam that have maximum bending moments are merely reinforced, the beams could be designed by the bending moment at the center of the H-shaped beam. To analyze the structural performance of the proposed end-reinforced beams (eco-girders). Four specimens were prepared with the following parameters: end-reinforced steel plate, reinforced bars, and reinforced studs and experimental tests of the specimens were performed.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.18 no.3
• /
• pp.225-240
• /
• 2006

In order to calculate bending moments of rectangular plates with three edges clamped the other free subjected to both a uniform load and a triangular load, a finite difference equation for the non-dimensional governing equation are presented and numerical solutions with different aspect ratios and/or number of grid points are analyzed. The finite difference solutions are obtained by use of grid points up to 11,520 and the optimum grid points according to aspect ratios of the plate are presented as well. The obtained numerical solutions are shown to satisfy the given x moment boundary condition at the free edge, which can not be satisfied in Levy's analytical solutions and peculiar behaviour of the calculated moments is observed around the corners between the free edge and fixed ones. The numerical solutions of bending moments subjected to both a uniform load and a triangular load are compared with the corresponding analytical solutions which are shown in very good agreement on the solution domain except the neighborhood of the free edge.