• Journal of the Korean Wood Science and Technology
• /
• v.29 no.2
• /
• pp.69-75
• /
• 2001

This study was carried out to investigate the properties of woodceramics made from thinned logs of Cryptomeria japonica. In order to find the effect of steam injection time on the woodceramics fabricated with boards, boards were made with the non-steamed treatment and steamed treatment 1, 5, 10 min. at $250^{\circ}C$. The percentage of weight loss was proportional to the increased density of board The reducing rate of length and thickness, however, decreased with increasing density of board. The rate of weight loss, length and thickness reduction in non-steamed board were slightly higher than those of steamed board. When the resin impregnation rate increased, the bending strength and compressive strength of woodceramics had a tendency to increase. The bending strength and compressive strength of woodceramics in non-steamed board was higher than those of steamed board. But there was little difference between dimensional and strength properties of woodceramics and steam injection time of board.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.33 no.3
• /
• pp.365-376
• /
• 2006

The purpose of this study was to evaluate the efficacy of blocking the oxygen in the air during the polymerization of sealant. All curing were performed with various light curing units under the application of oxygen gel barrier, stream of nitrogen and carbon dioxide gas for inhibition of oxygen diffusion into sealant surface. The results of present study can be summarized as follows : 1. The amount of eluted TEGDMA form the specimens cured with all the three different light units in the stream of $N_2$ and $CO_2$ gas and application of Oxygen gel barrier($DeOx^{(R)}$) were significantly lower than in the room-air atmosphere (Control) (p<0.05). 2. In the $DeOx^{(R)}$ application, the amount of eluted TEGDMA the specimen cured with PAC light for 10seconds was less than that cured in the stream of $N_2$ and $CO_2$ atmospheric conditions (p<0.05) 3. In the LED using 10 or 20sec irradiation times under the stream of $N_2$ and $CO_2$, the eluted TEGDMA showed to be no statistically significant difference (p>0.05). 4. The microhardness from the specimens cured with all the three different light units under each treated conditions were significantly higher than in the room-air atmosphere (p<0.05). 5. The surface treatment by $DeOx^{(R)}$, $N_2$ and $CO_2$ reduces the thickness of oxygen inhibited layer by sp proximately 49% of the untreated control value.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.156-160
• /
• 2006

This study investigated the characteristics of spray generated by a liquid-liquid co-axial swirl injector used in a combustor of the liquid rocket engine. The linear stability analysis[1] was introduced In liquid sheet breakup and Post[2]'s collision model which considers shattering was adopted on the collision model after breakup. Every model was implemented to KIVA[3], which was adopted as solve. To validate the implemented models the cases of high and low injection velocity were calculated respectively and each result agreed well with test results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.3
• /
• pp.99-105
• /
• 2011

This paper described the effect of the multiple injections on the emission characteristics and combustion stability in a common rail diesel engine. In order to investigate the influence of multiple injections in a passenger car diesel engine, the injection strategy was varied with pilot injection, post injection and one main injection at various conditions. Based on the experimental results, the combustion and emissions characteristics were analyzed for the various injection strategies such as main, pilot-main, double-pilot-main, double- pilot-main-post injection strategy. It is revealed that the $NO_X$, HC and CO emissions are reduced by double pilot and post injection at medium load, however, soot emission is increased. Also, in the case of multiple injection, the combustion pressure is increased smoothly near the TDC and the coefficient of variation and fuel consumptions are decreased.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.672-675
• /
• 2010

Spray characteristics for the modulation with a pulsed spray in low-frequency region were investigted by performing with additional internal pulsed injection. The 1st perturbative flow was generated by rotating-type pulsed device and the 2nd pulse source generated by the magnetic valve was used to modulate the 1st flow. A pattern of the modulated spray was observed through FFT result and visualization. In case of modulated spray with the 2nd pulse control, the width of up and down motion of the modulated spray is smaller than that of the spray without the 2nd pulse. Also, the depth of penetration of the down stream is higher than that of spray without the 2nd pulse.

• Fire Science and Engineering
• /
• v.29 no.3
• /
• pp.43-47
• /
• 2015

Water mist was sprayed on small compartment areas filled with smoke that formed from two different combustibles. The water-mist injection pressure and time were varied, and changes in the light extinction coefficient were measured over time. The smoke removal effect was analyzed with a light sensing smoke meter in different experimental conditions. Using the meter, the changes in smoke density were converted to changes in DC voltage over time to obtain the changes in the light extinction coefficient. The water mist was more effective in eliminating the smoke formed from glowing compared to flaming combustion. The smoke removal effect was significantly better with greater injection pressure and injection time.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.45-49
• /
• 2006

The flow around a foil with waterjet was investigated using the two-frame PIV(CACTUS 3.1) system. After separation, unsteady recirculation & reattachment region was shown as a result at reading edge. Separation area was decreased to 1/3 more by waterjet system with coanda effect. Angle of attack and waterjet velocity was a variable in the experiment. Each parameters was controlled to $0^{\circ}{\sim}35^{\circ}$ and 0[m/s]${\sim}$9.2[m/s]. The separation of flow appearanced at first when the angle of attack is $17^{\circ}{\sim}18^{\circ}$. However, according to grew up of velocity, beginning of the separation was delayed. In this experiment, vortex and separation region was disappeared by blown when each parameters are low level, and separation controlled more certainly.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.106-106
• /
• 2004

보일러에서 연소된 후 배출된 가스는 탈황목적으로 설치된 흡수탑 내에 유입되어 Slurry Spray Nozzle에서 분사된 Limestone Slurry에 의해 배기가스중의 SO$_2$를 흡수한 다음 반응조로 떨어지게 되지만 분사된 액적의 일부는 배기가스의 압력에 의하여 같은 유동 방향으로 미세한 Mist의 형태로 배기가스와 함께 흡수탑의 Outlet Duct를 통해 빠져나간다. 이 Mist(액적크기 40 $\mu\textrm{m}$이하)에는 고형 성분이 함유되어 있는데 보통 Chloride농도가 높아 탈황설비 후단 (duct, GGH, Stack)에 plugging, 부식 등의 문제를 유발하므로 Spray Header상부에서 Mist Eliminator를 설치하여 Mist를 제거하도록 한다.(중략)

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.127-127
• /
• 2004

입자분사 가공(abrasive jet machining)은 과거에는 녹(rust) 도색(painting)의 제거 흑은 디버링(deburring), 표면 처리 등의 용도에 국한되어 사용되어졌다. 한편 최근 들어 반도체 제작공정이나 MEMS 공정 등에 적용되는 실리콘(silicon) 등의 세라믹 재료의 미세가공분야가 주목받고 있으며, 따라서 이와 관련된 많은 연구가 진행되고 있다. 한편, 세라믹 재료는 파괴인성이 매우 낮고 취성이 강하기 때문에 크랙발생 후 큰 응력이 연속적으로 주어지면 크랙은 음속으로 진행되어 파단 되는 특성이 있어서 일반적인 기계가공이 매우 어렵다.(중략)

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1999.05a
• /
• pp.57-57
• /
• 1999

핵연료 펠렛제조공정의 단순화를 위하여 분말을 플라즈마로 용융시킨 후 이를 펠렛몰더에 직접 침적시키는 방법으로 핵연료를 제조하고자 하였다. 침적물의 밀도에 미치는 영향을 관찰하기 위하여 쉬스가스 조성, 플라즈마 동력, 챔버내부압력 및 분말 공급량, 입자크기, 분사관 위치, 분사거리 및 쉬스가스조성 등을 변수로 하였다$^{1)}$ . 실험으로 얻어진 결과는 ANOVA(Analysis of Variance)의 통계적 방법으로 각각의 인자가 밀도에 미치는 영향의 크기뿐만 아니라, 두 가지 이상의 인자가 조합되어 나타나는 영향에 대해서도 분석하였다.