• 대한기계학회논문집B
• /
• 제20권4호
• /
• pp.1510-1520
• /
• 1996

An experimental study on the flow over the axisymmetric backward-facing step was carried out. The purpose of the present study is to investigate the effect of the separating streamline curvature on the reattachment length and to understand the structure of recirculating flows. Local mean and fluctuating velocity components were measured in the separating and reattaching axisymmetric region of turbulent boundary layer on the wall of convex cylinder placed in a water tunnel by using 2-color 4-beam fiber optics laser Doppler velocimetry. The study demonstrates that the reattachment length increases with increasing separating streamline curvature. It is also observed that the reverse flow velocity and turbulent kinetic energy increase with an increase in the separating streamline curvature. In addition, the behavior of maximum turbulent stresses show that the effect of separating streamline curvature is larger in the region of recirculating zone(X/H<2) than in the region of reattachment point.

• 대한기계학회논문집B
• /
• 제36권9호
• /
• pp.923-930
• /
• 2012

입구유동 가진이 있는 층류 후향계단 유동에서 Pr수의 변화에 따른 열전달 특성변화를 조사하기 위하여 비정상 수치해석을 수행하였다. 입구는 가진주파수와 가진진폭의 변화에 따른 교란이 주어졌고, 온도함수의 물성치가 적용되었다. 열전달 변화에 대한 다양한 특징들이 열경계층 변화에 의해서 설명되었다. 물성치가 일정한 경우와 비교하였을 때, 물성치가 온도의 함수성이 있는 경우 Pr < 1인 조건에서 열전달은 감소하였고, 반대로 Pr > 1인 조건에서 열전달은 증가하였다. 또한 가진진폭이 증가함에 따라 계단 후류 바닥면에서 열전달도 증가하였다. 그렇지만 가진주파수 변화의 경우 St < 0.2인 조건에서 열전달이 크게 증가하는 특정주파수 영역이 존재하였다. 특히, 열전달의 증가는 재부착 길이의 rms값의 변동정도와 밀접한 관련이 있음을 보여주었다.

• 설비공학논문집
• /
• 제6권1호
• /
• pp.1-10
• /
• 1994

The flow and heat transfer characteristics behind a backward facing step located in a vertical channel has been studied. In this study, the numerical prediction has been performed by solving the Navier-Stokes equation and energy equation simultaneously with the SIMPLE algorithm embedied in TEACH code. Local heat flux was measured by using Schlieren Interferometer. The flow visualization was performed using the cylindrical lens and the laser beam that is scattered by the supplied glycerine particles. The velocity and temperature distributions, recirculation region, reattachment length, and local heat flux are obtained under the various parameters to investigate the buoyancy effect on the flow and heat transfer characteristics behind the step.

• 산업기술연구
• /
• 제19권
• /
• pp.59-65
• /
• 1999

This study is to analyze turbulent flow over a backward-facing step in a rectangular duct. The side wall effects on the internal flow were determined by varying the aspect ratio(defined as the step span-to-height ratio) from 1 to 20. In the flow behind a backward-facing step, separation, recirculation and redeveloping is occurred frequently. These phenomena appear in a particular variation by varying the aspect ratio. The results show that the aspect ratio has an influence on the velocity and reattachment length. When the AR is increased, the reattachment length is increased. For 6 over aspect ration, the rate of increase is decreased. The length of recirculation in the upper corner is increased, as the increase of aspect ration. It's width is not changed in the variation of aspect ration. The transverse, streamwise and spanwise velocities were decreased along the flow down stream of the step.

• 대한기계학회논문집
• /
• 제17권5호
• /
• pp.1253-1261
• /
• 1993

본 연구에서는 수직 평판에 위치한 후향계단면 위를 흐르는 유체유동의 특성, 즉 재부착점, 박리 및 재순환 영역에 미치는 부력의 영향을 수치해석 및 실험으로 조사한다. 유동의 가시화를 통해 재부착점의 위치를 측정하며 레이저도플러 유속계 (5W,Ar-Ion,DANTEC)에 의한 속도분포 및 CTA(constant temperature anemoneter,55M01 과 55M20, DANTEC)를 사용한 온도분포를 동시에 측정 함으로써 유동 특성 및 열전달에 미치는 부력의 영향을 검토한다.

• 대한기계학회논문집B
• /
• 제26권3호
• /
• pp.423-431
• /
• 2002

An experimental study is conducted to investigate the effect of two-frequency forcing on turbulent flow behind a backward-facing step at the Reynolds number of 27000 based on the step height. The forcing is provided from a thin slit located at the edge of the backward-facing step to increase mixing behind the backward-facing step and consequently to reduce the reattachment length. With single frequency forcing, the minimum reattachment length is obtained at the non-dimensional forcing frequency (F) of St$\_$h/ = 0.29. With two-frequency forcing, a subharmonic frequency (F/2) or biharmonic frequency (2F) is combined with the fundamental frequency (F), i.e. (F, F/2) or (F, 2F) forcing is applied. In the case of (F, F/2) forcing, the reattachment length is not much sensitive to the phase difference between F and F/2. However, the reattachment length significantly depends on the phase difference between F and 2F in the case of (F, 2F) forcing. At a certain range of the phase difference, the reattachment length becomes smaller than that of the single frequency forcing.

• 한국추진공학회지
• /
• 제20권6호
• /
• pp.83-90
• /
• 2016

이중 모드 램젯 엔진 모델의 램젯 모드 연소 시험을 수행하였다. 엔진 모델은 흡입구, 연소기 및 노즐로 이루어졌다. 로켓 기반 복합 사이클 엔진에 사용하는 것을 전제로 큰 후향 계단을 가지는 형상을 선택하였다. 시험은 마하 5, 고도 24 km 조건에서 수행하였다. 연료를 카울면과 바닥면에 분산하여 다중 분사를 한 경우에 안정적인 연소를 달성할 수 있었다. 또한 연료 당량비를 카울면에서 0.5, 바닥면에서 0.5로 하여 총 당량비 1.0으로 한 경우에 연소기 내부에서 열질식이 발생하여 유동이 아음속으로 조성되는 램젯 모드로 운전됨을 확인하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2378-2383
• /
• 2007

Direct Numerical Simulation was carried out to predict mass transfer in turbulent flow around a rotating stepped cylinder. This investigation is a follow-up study of Nesic et al. [Corrosion, Vol. 56, No. 10, pp. 1005 - 1014] The original motivation of this work stemmed from the efforts to design a simple device which can generate flows of high turbulence intensity at low cost for corrosion researchers. Two cases were considered; Sc=1 and 10 both at Re=335. Here, Sc and Re stand for Schmidt number and Reynolds number, respectively, based on the step height and the surface speed of the cylinder upstream the step. Main focus was placed on the correlation between turbulent fluctuation and concentration field. The spatio-temporal evolution of concentration field is discussed. The numerical results are qualitatively compared with those of the experiment conducted with the same flow configuration.

• 한국전산유체공학회지
• /
• 제15권2호
• /
• pp.55-61
• /
• 2010

A dependence of weighting parameter in preconditioning method for solving low Mach number flow with incompressible flow nature is investigated. The present preconditioning method employs a finite-difference method applied Roe‘s flux difference splitting approximation with the MUSCL-TVD scheme and 4th-order Runge-Kutta method in curvilinear coordinates. From the computational results of benchmark flows through a 2-D backward-facing step duct it is confirmed that there exists a suitable value of the weighting parameter for accurate and stable computation. A useful method to determine the weighting parameter is introduced. With this method, high accuracy and stable computational results were obtained for the flow with low Mach number in the range of Mach number less than 0.3.

• 대한기계학회논문집
• /
• 제18권3호
• /
• pp.624-634
• /
• 1994

A numerical method which combines equal-order velocity-pressure formulation originated from SIMPLE algorithm and streamline upwinding method has been developed. To verify the proposed numerical method, we considered the lid-driven cavity flow and backward facing step flow. The trend of convergence history is stable up to the error criterion beyond which the maximum value of error is oscillatory due4 to the round-off error. In the present study, all results were obtained with the single precision calculation up to the given error criterion and it was found to be sufficient for our purpose. The present results were then compared with existing experimental results using laser doppler velocimetry and numerical results using finite difference method and mixed interpolation finite element method. It has been shown that the present method gives accurate results with less memories and execution time than the coventional finite element method.