• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.74-78
• /
• 2012

본 연구는 하천에서 식생에 의한 흐름구조 변화가 오염물질 이동에 미치는 영향을 알아보기 위해 흐름방향 확산계수를 산정하였다. 정수식생 조건에서 횡방향 수심적분된 와점성계수는 비식생 조건에서의 와점성계수와 다르게 적용되어야 하며 이를 위해 유량 횡분배법을 Jordanova and James (2003) 실험에 적용하였다. 제시된 실험조건을 잘 재현하는 와점성계수의 값을 역산하였으며, 이에 관한 산술평균 값을 향후 수리모형의 적용을 위해 정수식생 조건에서의 무차원 와점성계수로 제안하였다. 결정된 무차원 와점성계수를 이용하여 부분식생 개수로 흐름에서 흐름방향 확산계수를 산정하여 오염물질의 이동에 대한 특성을 분석하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.13 no.3 s.55
• /
• pp.173-180
• /
• 2009

Very-early strength latex-modified concrete(below ; VES-LMC) was developed for possible early-opening-to-traffic after overlay of bridge deck concrete. The purpose of this study is to analyze the cause of map, transverse and longitudinal cracking in VES-LMC and to provide a control method for minimizing occurrence of cracking. The proposed prevention method against map and transverse cracking was verified by field data. VES cement was modified as the unit cement content was reduced from 390kg/$m^3$ to 360kg/$m^3$. The maximum size of coarse aggregate was increased from 13mm to 19mm. The wire mesh and steel fiber were adopted in concrete mixture. From the results, the proposed prevention method against map and transverse cracking was verified since structural cracking was not occurred until 3 years after overlay.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.883-888
• /
• 2007

일반적인 하천의 흐름방향으로 발생하는 주흐름(primary flow)에 중첩하여 주흐름 방향의 수직단면에 이차류(secondary flow)가 발생하게 되며 이러한 이차류의 발달은 투입된 오염물질의 횡혼합을 증대시킨다. 오염물질의 혼합은 이송(advection)과 확산(diffusion) 또는 분산(dispersion)의 과정으로 설명되며 본 연구에서는 수로전체의 혼합과정을 설명하기 위해서 이송 확산 방정식을 적용하였다. 본 연구에서는 실험수조를 $150^{\circ}$의 중심각을 갖는 S자 형태의 만곡수로를 제작하여 유량조건은 15, 30, $60\;{\ell}l/sec$의 세 가지 경우로, 수심은 15, 20, 30, 40 cm의 경우로 총 12 케이스의 실험을 수행하였다. 유속장의 측정은 Sontek사의 3차원 micro-ADV(Acoustic Doppler Velocimeter)를 이용하였다. 오염물질 확산실험은 소금물 용액에 주변수와의 밀도차를 없애기 위해서 메탄올 용액을 첨가하여 추적자로 이용하여 농도장의 분석을 일본 KENEK사의 전기전도도계(conductivity meter)와 Gartner사의 DAS(data acquisition system)를 이용하여 횡방향 유속장의 분포와 오염운의 거동을 비교하여 다음과 같은 결론을 얻게 되었다. 주 흐름은 직선구간에서는 중앙에서 최대 유속을 나타내며, 좌우대칭적인 유속분포의 모습을 보이고, 만곡부에서는 수로안쪽을 따라 최대유속이 발생하였다. 수로의 직선구간에서는 최대유속이 발생하는 즉, 중앙에서의 오염물질의 분산이 가장 활발하게 이뤄졌으며 농도의 퍼짐형상인 오염운 역시 만곡부에서는 수로만곡부의 안쪽을 따라 확산 이동함을 알 수 있었다. 만곡부 외측에서는 오염물질의 정체현상이 일시적으로 발생하며, 유속구조의 횡방향 비대칭구조로 인한 종 횡방향의 분리현상이 발생하고, 오염운의 중첩현상이 종방향으로 연속되게 나타난다. 향후 수심방향 거동을 포함한 3차원적 분석이 요구되며 이 연구결과는 2차원적 수치해석의 적용 및 분석 자료로써 이용이 가능하다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.6B
• /
• pp.573-581
• /
• 2006

This paper presents a turbulence modeling of the open-channel flows over smooth-rough bed strips. A Reynolds stress model is used for the turbulence closure. The simulated mean flow and turbulence structures are compared with the previously reported experimental data. Comparisons reveal that the developed Reynolds stress model successfully predicts the mean flow and turbulence structures of open-channel flows over smooth-rough bed strips. The computed flow vectors show cellular secondary currents, of which the upflow occurs over the smooth bed strip and the downflow over the rough bed strip. It is found that the cellular secondary currents affect the mean flow and turbulence structure. A budget analysis of the streamwise vorticity equation is also carried out to investigate the mechanism by which the secondary currents are generated.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.13 no.1
• /
• pp.87-95
• /
• 2000

The two eigenvalues (elastic critical load and natural frequency of lateral vibration) of sinusoidally tapered bats with simply supported ends were determined by the finite element method. For the convenience of structural engineers who are engaged in the structural design or vibration analysis of tapered beam-columns, eigenvalue coefficients were expressed by simple algebraic equations. The validity of each algebraic equation was confirmed by the value of unity for each correlation coefficient. The influence of axial thrust on the lateral vibration frequency was also investigated. For this purpose, the axial thrust was increased successively and the corresponding frequency was calculated. The approximate linear relationship between the axial thrust and the square of the frequency was confirmed lot each of the tapered members.

• Journal of the Korea Institute of Building Construction
• /
• v.9 no.6
• /
• pp.169-174
• /
• 2009

We conducted structural analysis to investigate disadvantage of wire-mesh arranged at the plane and to develop three-dimensionally bent U-type wire-mesh. In all case that distributed loading at the whole top slab and the half top slab, and the wire mesh was bent $45^{\circ}$, flexura tensile stress was the fewest in both positive moment and negative moment, and the wire mesh was bent $45^{\circ}$ in crossway the shear stresss was the fewest. Therefore, by arranging wire-mesh with $45^{\circ}$ more bent than plane, flexura tensile stress, shear stress, displacement will be reduced and structural function will be improved.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.6
• /
• pp.573-580
• /
• 2014

In this paper, axial strains and lateral displacements of columns in a 58-story reinforced concrete building were measured using vibrating wire gauge and laser scanner, respectively, and compared with predicted values. Predictions were obtained using ASAP, which is a 3D construction stage analysis program developed based on PCA report. Comparisons indicated that columns in the middle of floor plan showed good correlation with predictions. However, the columns in the corners showed some deviations. Lateral displacement of columns between measurement and estimation showed similar trends but considerable deviations, which are seemingly caused by construction error of column faces, and inaccuracy in differential vertical displacement prediction.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.1
• /
• pp.112-121
• /
• 2017

Large eddy simulations of transitional flows around a stud installed on a flat plate have been performed to investigate an influence of grid resolution on turbulence stimulation by the stud. Because streamwise vortical structures generated by the stud played an important role in turbulence stimulation of boundary layer, streamwise vorticity was compared in the wake region behind the stud when the number of grids increased or decreased by a ratio of ${\sqrt{2}}$ in streamwise, wall-normal and spanwise directions respectively. The streamwise vorticity was shown to be mainly affected by spanwise grid resolution (${\Delta}z^+$) rather than streamwise and wall-normal grid resolution. In a viewpoint of numerical efficiency as well as physical resolution, ${\Delta}x^+{_{min}}=7.6$, ${\Delta}x^+{_{max}}=41$, ${\Delta}y^+{_{wall}}=0.25$ and ${\Delta}z^+=7.6$ was found to be desirable. Once a grid resolution was determined in each direction, a grid verification was carried out by increasing or decreasing the grid resolution y a ratio of ${\sqrt{2}}$ in all directions. The grid uncertainties of pressure and drag coefficients were 21.6 % and 2.8 % while the corrected uncertainties were 2 % and 0.3 %, respectively.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.13 no.1
• /
• pp.105-113
• /
• 2000

Seismic behavior of 3-dimensional setback structures showing abrupt reductions of the floor size within the structure height and the effect of in-plane deformations of floor slabs on the seismic behavior of those structures are investigated. To find out general seismic behavior of 3-dimensional setback structures two parameters, level of setback(L/sub s/) and degree of setback(R/sub s/) are used. Analysis results obtained from forty eight setback structures show that a sudden change in story shear near setback level is occurred for irregular setback structures. The effect of in-plane deformation of floor slabs on the seismic behavior of setback structures is greatly influenced by the arrangement of lateral load resisting elements and it is more pronounced for frame-shear wall system showing large difference in stiffness among the lateral load resisting elements. The in-plane deformation of floor slabs results in reduced base shear, especially for FW-type structures with L/sub s/=1.0. Also, it brings about reduced story shear for the lateral load resisting element with shear wall and increase in story shear lot the lateral load resisting element without shear wall. The in-plane deformation of floor slabs at the base portion and/or tower portion due to difference in stiffness among the lateral load resisting elements brings about increment of floor displacements at all floor level.

• Journal of the Korea Concrete Institute
• /
• v.24 no.6
• /
• pp.705-714
• /
• 2012

Precast reinforced concrete bridge columns with hollow rectangular section were tested under cyclic lateral load with constant axial force to investigate its seismic performance. After all the precast column segments were erected, longitudinal reinforcement was inserted in the sheath prefabricated in the segments, which were then mortar grouted. Main variables of the test series were column aspect ratio, longitudinal reinforcement ratio, amount of lateral reinforcement, and location of segment joints. The aspect ratios were 4.5 and 2.5, and the longitudinal steel ratios were 1.15% and 3.07%. The amount of lateral reinforcement were 95%, 55%, 50%, and 27% of the minimum amount for full ductility design requirements in the Korean Bridge Design Code. The locations of segment joints in plastic hinge region were 0.5 and 1.0 times of the section depth from the bottom column end. The test results of cracking and failure mode, axial-flexural strength, lateral load-displacement relationship, and displacement ductility are presented. Then, safety of the ductility demand based seismic design in the Korean Bridge Design Code is discussed. The column specimens showed larger ductility than expected, because buckling of longitudinal reinforcing bar was prevented due to confinement developed not only by transverse steel but also by sheath and infilling mortar.