• Proceedings of the KIPE Conference
• /
• 2011.11a
• /
• pp.153-154
• /
• 2011

본 논문은 비대칭 2상 SRM의 센서리스 속도제어를 위한 초기각 검출 및 초기 기동방식과 자속관측기를 적용한 센서리스 제어에서 전동기의 온도 및 파라미터 변동에 의한 자속 오차 성분으로 인해 발생하는 위치 추정오차를 보상하기 위한 새로운 보상기를 제안한다. 제안된 방식은 전압펄스 인가로 초기각을 검출하고 검출된 초기 위치정보를 바탕으로 동일한 전압펄스 인가를 통해 비여자상이 여자상이 되는 회전자 위치를 검출하여 상여자를 교체하는 초기기동을 통해 자속관측기를 적용한 센서리스 제어로 안정적으로 진입하도록 한다. 이 때, 제안된 추정위치 보상기를 통해 추정된 센서리스 위치를 순시적으로 보상한다.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.3
• /
• pp.154-161
• /
• 2005

This paper proposes a speed-sensorless induction motor control system using a rotor speed compensation. To explain the proposed system, this paper describes an induction motor model in the synchronous reference frame for the vector control. The rotor flux is estimated by the rotor flux observer using the reduced-dimensional state estimator technique. The estimated rotor speed is directly obtained from the electrical frequency, the slip frequency, and the rotor speed compensation with the estimated q-axis rotor flux. The error of the rotor time constant is indirectly reflected in the rotor speed compensation using the compensation of the flux error angle. To precisely estimate the rotor flux, the actual value of the stator resistance, whose actual variation is reflected, is derived. An implementation of pulse-width modulation (PWM) pulses using an effective space vector modulation (SVM) is briefly mentioned. For fast calculation and improved performance of the proposed algorithm, all control functions are implemented in software using a digital signal processor (DSP) with its environmental circuits. Also, it is shown through experimental results that the proposed system gives good performance for the speed-sensorless induction motor control.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.2
• /
• pp.168-175
• /
• 2009

This paper proposes an enhanced algorithm for sensorless control of 45,000rpm/22kw type Permanent Magnetic Synchronous Motor (PMSM) with air-foil bearing. The proposed algorithm is based on iterative adaptive flux observer for sensorless control of the motor in wide speed range by on-line estimating angle and velocity of rotor. Simulation error between actual and estimated angle of rotor is analyzed to enhance characteristics of frequency response of conventional adaptive flux observer, which results in stable response in wide range of speed. Using the iteration number for stable phase-delay characteristics, the observer enhances the dynamic characteristics of the observer within current control period. The experiment results show the reliable performance of the proposed algorithm through starting to high speed operating range.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.251-252
• /
• 2014

본 논문은 직접토크 제어에서 토크와 자속 오차에 따라 결정된 전압 벡터가 가지고 있는 자속 및 토크 출력 특성을 전압의 d-q 해석을 통해서 분석하고, 6섹터 방식과 12섹터 방식에서 각 전압에 의해 발생되는 토크 및 자속 특성을 회전자 위치에 따라 해석하였다. 또한, 전압벡터의 전압특성을 모의하기 위한 근사 전압함수를 제시하고, 근사전압함수를 통해 직접토크 제어 방식에서의 자속 및 토크 제어의 성능향상이 가능함을 실험을 통해 검증하였다.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.35T no.1
• /
• pp.90-98
• /
• 1998

This paper is to describe the improved vector control which can control the induction motor robustly in low speed. When the induction motor is drived with low speed, below 10 percent of the rated speed, an algorithm which can compensate the error of unit vector angle generated by the harmonics is proposed. Another algorithm which can be tuned to the rotor time constant so that nay be robust to the rotor parameter change in low speed and transient state was proposed. The ripple of flux and torque was reduced by the proposed vector control and then the stable output characteristics was obtained in low speed. When the input and output is sinusoidal, the proposed vector control, the direct vector control and the indirect vector control were analyzed and compared in the low speed characteristics. And each control characteristics is compared and analyzed in state of containing harmonics. The estimation and tunning performance of rotor time constant is confirmed with simulation. The whole control system is implemented by real hardware and experimented to compare the proposed vector control with the direct vector control. As a result of the experiment with two control methods in low speed, the torque ripple of the proposed vector control is improved by 45 percent than the direct vector control. And it is confirmed that the flux current ripple is reduced in 0.2 p.u. and torque current ripple is reduced in 0.6 p.u. It is confirmed that the rotor time constant by the estimation and the tunning algorithm is tunned by the real rotor time constant. Finally, it was confirmed that the validity and robustness for the proposed vector control in low speed existed.