• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1A
• /
• pp.75-89
• /
• 2006

This paper presents a practical and realistic Life-Cycle Cost (LCC) optimum design methodology of steel bridges considering time effect of bridge reliability under environmental stressors such as corrosion and heavy truck traffics. The LCC functions considered in the LCC optimization consist of initial cost, expected life-cycle maintenance cost and expected life-cycle rehabilitation costs including repair/replacement costs, loss of contents or fatality and injury losses, road user costs, and indirect socio-economic losses. For the assessment of the life-cycle rehabilitation costs, the annual probability of failure which depends upon the prior and updated load and resistance histories should be accounted for. For the purpose, Nowak live load model and a modified corrosion propagation model considering corrosion initiation, corrosion rate, and repainting effect are adopted in this study. The proposed methodology is applied to the LCC optimum design problem of an actual steel box girder bridge with 3 continuous spans (40 m+50 m+40 m=130 m), and various sensitivity analyses of types of steel, local corrosion environments, average daily traffic volume, and discount rates are performed to investigate the effects of various design parameters and conditions on the LCC-effectiveness. From the numerical investigation, it has been observed that local corrosion environments and the number of truck traffics significantly influence the LCC-effective optimum design of steel bridges, and thus realized that these conditions should be considered as crucial parameters for the optimum LCC-effective design.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.3A
• /
• pp.201-209
• /
• 2010

Generally, PSC girder bridge uses total gross cross section to resist applied loads unlike reinforced concrete member. Also, it is used as short and middle span (less than 30 m) bridges due to advantages such as ease of design and construction, reduction of cost, and convenience of maintenance. But, due to recent increased public interests for environmental friendly and appearance appealing bridges all over the world, the demands for longer span bridges have been continuously increasing. This trend is shown not only in ordinary long span bridge types such as cable supported bridges but also in PSC girder bridges. In order to meet the increasing demands for new type of long span bridges, PSC hollow box girder with H-type steel as compression reinforcements is developed for bridge with a single span of more than 50 m. The developed PSC girder applies compressive prestressing at H-type compression reinforcements using unbonded PS tendon. The purpose of compressive prestressing is to recover plastic displacement of PSC girder after long term service by releasing the prestressing. The static test composed of 4 different stages in 3-point bending test is performed to verify safety of the bridge. First stage loading is applied until tensile cracks form. Then in second stage, the load is removed and the girder is unloaded. In third stage, after removal of loading, recovery of remaining plastic deformation is verified as the compressive prestressing is removed at H-type reinforcements. Then, in fourth stage, loading is continued until the girder fails. The experimental results showed that the first crack occurs at 1,615 kN with a corresponding displacement of 187.0 mm. The introduction of the additional compressive stress in the lower part of the girder from the removal of unbonded compressive prestressing of the H-type steel showed a capacity improvement of about 60% (7.7 mm) recovery of the residual deformation (18.7 mm) that occurred from load increase. By using prestressed H-type steel as compression reinforcements in the upper part of cross section, repair and rehabilitation of PSC girders are relatively easy, and the cost of maintenance is expected to decrease.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.443-446
• /
• 2009

In this study, a series of degradation test for structural adhesives was performed to investigate the possibility of replacement of the alternative adhesives to the conventional adhesives. Four types of the adhesives were exposed to combined environmental conditions over 1000 hours at an accelerated aging tester, which can simulate natural weather conditions such temperature, moisture and ultraviolet. Mechanical and chemical properties of the adhesives were evaluated through material testing system and FT/IR spectrometer. According to the results, the conventional adhesives can be replaced by the alternative adhesives because the alternative adhesives were more stable to environmental conditions rather than the conventional adhesives.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.3
• /
• pp.207-212
• /
• 2013

APR1000(Advanced Power Reactor 1000) was developed to export 1000MW nuclear power plants by adding ADFs(Advanced Design Features) including 60 years design life, local frequency control operation, 0.3g SSE, etc. to OPR1000(Optimized Power Reactor 1000). In this paper, environmental fatigue analyses for the reactor vessel in APR1000 have been performed as per Reg. Guide 1.207. Outlet nozzle, which has a relatively high cumulative usage factor in the reactor vessel was evaluated and a structural integrity is maintained under the reactor coolant environment.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.3
• /
• pp.15-20
• /
• 2013

The graphites as airtight structure seals prevent high-pressure and high-temperature gas from flowing into actuator of propulsion system and generate lubricant film during wear procedure to assist lubricant and sealing. In this study, the tribological characteristics of the graphite in high-temperature are evaluated. In order to evaluate the tribological characteristics of high density graphite(HK-6), variables which are temperature, sliding speed and contact load are set. this study suggest optimized environment conditions through the wear properties of graphite. Consequeantly, high temperature is better than at room temperature to generate lubricant film, so that friction coefficient of graphite is lower at high temperature than at room temperature.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.670-673
• /
• 2010

무기저 손상 진단 기법은 능동센서를 이용하여 과거의 기저자료와 현재 상태에서 취득한 유도파의 정보를 비교하지 않고, 구조물의 현재 상태에서 취득한 신호만을 분석함으로써 구조물의 상태를 진단하는 기법이다. 온도 변화 및 하중 변화 등의 외부 환경의 변화에 민감한 유도파의 특성으로 인하여 기저자료를 이용하는 과거의 방법론은 현실적용성이 떨어질 우려가 있다. 본 무기저 손상 진단 기법은 외부 환경적 영향을 최소화함으로써 구조물의 상태를 효율적으로 진단할 수 있다. 최초, 본 연구진에서 제안하였던 무기저 기법은 두 쌍의 능동센서를 구조물에 양면 대칭으로 배치시켜 능동센서의 극성을 이용한 방법이었다. 하지만 실제 구조물의 양면에 완벽한 대칭성을 유지하며 능동센서를 배치시키는 것은 사실상 불가능하다. 이와 같은 한계점을 극복하기 위해 신개념의 듀얼 능동센서를 활용한 무기저 손상 진단 기법이 제안되었고, 수치해석 및 연구실 환경에서 제한적으로 그 실용성이 검증되었다. 본 논문에서는 무기저 손상 진단 기법의 실 구조물에의 적용성을 폐교량을 대상으로 검토하였다. 특히, 보강재를 포함하는 영역에서 본 기법을 적용함으로써 실제 구조물에 적용 가능성을 검증하였다.

• Journal of Environmental Impact Assessment
• /
• v.21 no.1
• /
• pp.171-184
• /
• 2012

하천 수위를 유지하거나 농업용수를 취수 할 목적으로 조성되는 크고 작은 보는 용수공급 시설로 이용되고 있으나, 하천 생물이동의 차단, 보 상류부의 수질악화, 수변 생물서식처의 변화, 하천경관 훼손과 같은 환경적 문제를 초래하고 있다. 더욱이 도시화가 진행됨에 따라 토지이용의 변화, 시설의 노후화 등으로 매년 50~150개 정도의 보가 폐기되고 있는 현실이다. 본 연구는 하천에 설치되었으나 용도와 기능이 상실된 보를 철거하여 생태적 연속성을 확보하고 하천 본래의 모습으로 되돌려 주며, 하천의 생태적 건강성을 회복 및 향상 시키고자 하였다. 보 철거 시범사업으로 공릉천에 설치된 길이 76m, 높이 1.5m의 공릉2보와, 한탄강에 설치된 길이 190m, 높이 2.8m의 고탄보를 철거하였고, 각 시범사업 대상지의 물리/화학/생태특성 모니터링 분석을 수행하였다. 그 결과 철거 직후 보의 직 상류부에 전체적으로 침식이 발생하고, 보 하류부는 여울, 하중도, 사주, 침식 등 다양한 지형으로 변모되었다. 본 연구를 통하여 하천복원의 취지에 맞는 하천 본래의 모습에 가까운 하천으로 복원하기 위해서는 기능 및 용도가 상실된 보의 경우는 기존의 보체를 개량하거나 어도를 설치하여 주는 것 보다 구조물 자체의 완전철거를 통한 생물 이동통로 조성이 바람직하다고 판단된다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.2A
• /
• pp.391-399
• /
• 2006

Plate girders with variable depths have been often used at piers considering not only the economy but also an aesthetic aspect. Tapered plate girders exhibit more complicated behaviors than prismatic girders especially under shear. However, a comprehensive design method for the determination of the shear strength has yet to be developed mainly due to lack of study. In this study, investigated is the buckling and ultimate behaviors of tapered plate girders subjected to shear through finite element analyses. From the analysis results, a simple design formula is suggested for the evaluation of the shear strength of tapered plate girders.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.75-75
• /
• 2011

본 논문에서는 진동중인 교량 거더에 작용하는 풍하중을 산정하고 그에 따른 플러터 발생풍속을 예측하기 위하여 분산형 전산환경을 활용한 수치해석 연구를 수행하였다. 분산형 전산환경은 웹 포탈을 기반으로 수치해석 환경을 제공하는 수치풍동 시스템으로서, 전산유체역학(CFD : Computational Fluid Dynamics)에 대한 전문지식이 부족한 사용자들도 격자생성, 수치해석자를 이용한 계산, 가시화 등의 전 과정을 편리하게 수행할 수 있는 차세대 토목분야 연구 환경이다. 본 시스템은 그리드스피어(GfidSphere)를 기반으로 구성되었으며, 기본적으로 사용자 관리, 세션 관리, 그룹 관리, 레이아웃 관리 등을 제공하여 사용자가 포탈을 통해서 다양한 서비스를 쉽게 사용할 수 있는 환경을 구축하도록 도와준다. 수치해석을 위한 유체 지배방정식은 2차원 비정상 비압축성 RANS(Reynolds-Averaged Navier-Stokes) 방정식이며, pseudo compressibility 방법을 적용하였다. 비정상 유동장을 해석하기 위하여 이중시간 전진법(dual time stepping)을 사용하였으며, 수렴가속화를 위해 Multi-grid 기법을 적용하였다. 또한 난류 유동장 해석을 위해서 $k-{\omega}$ SST 난류 모델을 사용하였으며, 난류 천이 과정에서의 유동을 모사하기 위하여 Total stress limitation 방법을 적용하였다. 교량 거더의 연직과 회전방향의 2자유도 움직임을 모사하기 위하여 동적격자 기법을 도입하였다. 교량 거더 주변의 비정상 유동해석 결과를 통해, 거더 표면에서 떨어져나가는 크고 작은 와류의 영향으로 양력 및 모멘트 계수 그래프가 중첩된 진폭과 주기를 갖고 주기적으로 나타나는 것을 확인할 수 있었다. 또한 계산된 비정상 공기력을 적용한 2자유도 플러터 방정식을 통하여 플러터 발생풍속을 산정하였다. 최종적으로 본 연구에서 계산된 결과의 타당성을 검증하기 위하여 수치적으로 구한 플러터 발생풍속과 기존의 실험 및 수치해석 결과를 비교하였으며, 결과는 잘 일치하였다.

• Geotechnical Engineering
• /
• v.11 no.2
• /
• pp.29-36
• /
• 1995

Load testis are executed on model reticulated root piles (RRP) to figure out the optimum slanting angle in the piles installation. One set of model RRP consists of 8 slanting piles which are installed in circular patterns forming two concentric circles, each of which is made by 4 piles. Each pile which is a steel bar of 5m in diameter and 300mm in length is coated to become a pile of 6.5mm in diameter. The slanting angle of the model RRP varies from 0$^{\circ}$ to 20$^{\circ}$ Comparing ultimate bearing capacities of the model RRP of different installation angles, it is observed that the ultimate capacities of the RRP increase as the installation angle increases until 15$^{\circ}$, and the optimum slanting angle of the RRP is around 15$^{\circ}$ The ultimate bearing capacity of the 15$^{\circ}$-RRP is found to be 22% bigger than that of the vertical RRP and 120% bigger than that of the circular surface footing whose diameter is same with the circle formed by outer root piles'heads. However, it is noticed that when the slanting angle of the RRP is increased over 15$^{\circ}$, the ultimate capacity starts to be reduced. The ultimate capacity of 20$^{\circ}$-RRP is even smaller than that of the vertical RRP by as much as 5%. From the observation of the load settlement curve obtained during the RRP load tests, it is known that as the slanting angle gets bigger the load -settlement behavior becomes more ductile.