• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.6
• /
• pp.710-718
• /
• 2017

After Typhoon Chaba (No.18, 2016) collided with Manseongri Beach, a coastal improvement project was carried out since strong external forces such as waves, storm surges and wave-induced currents were observed to cause beach deformation. The shoreline, beach area and beach volume were periodically surveyed. On the basis of this field data, the beach deformation that occurred at Manseongri Beach has been formally described. Over three months after beach nourishment work began, the beaches were gradually stabilized in terms of natural external forces. However, this stabilization was interrupted by Typhoon Chaba. After two months of typhoon weather, the beach returned to a stable state and no changes were observed until one year after the beach recovery work. Just after the typhoon hit, the shoreline receded from the northern side, where no reduction of external forces occurred, while the rear beach area submerged by breakwater advanced. Also, the beach volume decreased by $3,395m^3$ after the typhoon, due to erosion that occurred on the northern beach, with deposition taking place on the southern backshore area. Therefore, it has been concluded that the coastal improvement project undertaken at Manseongri Beach has significantly contributed to conservation in areas of wave-dominant sediment transport.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.4
• /
• pp.338-347
• /
• 2023

Jinhae Bay, characterized by frequent runaway ships and strong winds during typhoon attacks, poses a high risk of maritime accidents such as ship collisions and groundings. This study aims to determine a safe separation distance between ships in the Jinhae Bay anchorage, considering the unique environmental characteristics of the Korean sea area. Analysis revealed that an average of 100-200 ships anchor in the typhoon avoidance area in Jinhae Bay during typhoon attacks, with approximately 70% of ships experiencing anchor dragging owing to strong external forces exceeding 25 m/s wind speeds. In this study, we analyzed and presented the separation distances between ships during anchoring operations based on domestic and international design standards, separation distances between ships used as actual typhoon shelters in Jinhae Bay, and appropriate safe distances for ships drifting under strong external forces. The analysis indicated that considering the minimum criteria based on the design standards and emergency response time, a minimum safe distance of approximately 400-900 m was required. In cases where ample space was available, the separation distance was recommended to be set between 700 to 900 m. The findings of this study are anticipated to contribute to the development of guidelines for establishing safe separation distances between ships seeking refuge from typhoons in Jinhae Bay in the future.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.7
• /
• pp.857-862
• /
• 2023

In order for an autonomous ship to arrive near the pier and automatically berth without the help of a tugboat or pilot, it is necessary to recognize the pier and calculate the thruster output and output angle for berthing to the pier at a fixed berthing speed under given external force conditions. Therefore, in this study, the external force and moment acting on the ship while berthing were analyzed, and the thruster output calculation for automatic berthing was designed and the basic concept for the development of the automatic berthing program was designed. The wind pressure applied to the hull by the wind while the ship is berthing was calculated based on the wind pressure area and the wind direction angle and the turning moment to rotate the ship according to the transverse force of the ship was calculated. Considering the force acting on the ship and the turning moment during berthing, a theoretical formula was presented to calculate the thruster output and output angle for berthing parallel to the pier, and the turning due to other variables was controlled by the PID controller. In addition, the basic concept for program development was presented by analyzing the input elements necessary for the theoretical formula.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.6D
• /
• pp.675-683
• /
• 2009

A Basic experimental study for the development of vibration-power generation system from the vibration energy of urban infrastructure, such as a railroad, highway, and bridges, was carried out to harvest electricity from moving vehicles. Starting with the proposal of vibration power generator which converts vibration energy to an electric power by using self-induction technology, the research explains the basic concept of self-induction technology and the dynamic characteristics of a ibration power generator. Also, in order to analyze the correlation of an electromotive force from vibration power generator which depends on external force and vibration speeds, many indoor experiments with various variables were achieved. Based on the experimental results, a vibration power generator system's ability were analyzed. With those results, basic data of vibration power generator system to acquire the maximum available power was confirmed.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.5
• /
• pp.594-604
• /
• 2021

To evaluate the causes of beach erosion in Sinji-Myeongsasimni Beach, external forces, such as tides, tidal currents, and waves, were observed seasonally from March 2019 to March 2020, and the surface sediments were analyzed for this period. In addition, the shoreline positions and beach elevations were regularly surveyed with a VRS GPS and fixed-wing drone. From these field data, the speed of the tidal currents was noted to be insufficient, but the waves were observed to af ect the deformation of the beach. As the beach is open to the southern direction, waves of heights over 1 m were received in the S-SE direction during the spring, summer, and fall seasons. Large waves with heights over 2 m were observed during typhoons in summer and fall. Because of the absence of typhoons for the previous two years from July 2018, the beach area over datum level (DL) as of July 2018 was greater by 30,138m² compared with that of March 2019, and the beach area as of March 2020 decreased by 61,210m² compared with that of March 2019 because of four typhoon attacks after July 2018. The beach volume as of March 2019 decreased by 5.4% compared with that of July 2018 owing to two typhoons, and the beach volume as of September 2019 decreased by 7.3% because of two typhoons during the observation year. However, the volume recovered slightly by about 3% during fall and winter, when there were no high waves. According to the sediment transport vectors by GSTA, the sediments were weakly influxed from small streams located at the center of the beach; the movement vectors were not noticeable at the west beach site, but the westward sediment transport under the water and seaward vectors from the foreshore beach were prominently observed at the east beach site. These patterns of westward sediment vectors could be explained by the angle between the annual mean incident wave direction and beach opening direction. This angle was inclined 24° counterclockwise with the west-east direction. Therefore, the westward wave-induced currents developed strongly during the large-wave seasons. Hence, the sand content is high in the west-side beach but the east-side beach has been eroded seriously, where the pebbles are exposed and sand dune has decreased because of the lack of sand sources except for the soiled dunes. Therefore, it is proposed that efforts for creating new sediment sources, such as beach nourishment and reducing wave heights via submerged breakwaters, be undertaken for the eastside of the beach.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.19 no.1
• /
• pp.62-73
• /
• 2016

The variation of groundwater by wave, tide and precipitation conditions is closely related to the vegetation environment at the natural vegetation and sandy based beach, and it has a significant impact on the vegetation development and ground stabilization. In this study, the water temperature, electrical conductivity, and pressure were monitored at five observational stations normal to the Jinu-do(Island) shoreline of Nakdong river estuary from March 2012 to September 2014 (approximately 799 days) with the aim of measuring the variation in groundwater-table characteristics. The purpose of the study was to identify factors (tide, wave etc.) affecting groundwater-table variation using time series and correlation analysis, and to record spatial variations in the groundwater level and electrical conductivity as a result of storm events. The observational station in the intertidal zone was strongly affected by wave period and tide level. During the storm period, the groundwater-table and electrical conductivity were stabilized at the edge of sand dunes, vegetation, and areas of transition between freshwater and seawater.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.6
• /
• pp.973-991
• /
• 2022

Globally, several countries with sea are using eco-friendly energy resources through offshore wind power development by overcoming the weak point of the existing power generation method. The sea has the advantage of being able to develop large scale wind farms in wide waters, but the installation of marine structures threatens the safe operation of vessels. Accordingly, a standard guideline for safe navigation by analyzing the mutual effects between ship routes and offshore wind site was presented by the PIANC. Nonetheless, the standard guideline calculated the same safe distance in all situations. Therefore, this study developed a calculation model for an optimal safe distance between ship routes and offshore wind sites by reflecting the ship's maneuvering, encounter situations, environmental force, traffic density, offshore wind power generators, and channel types. As a result of the validation simulation, the developed model showed that the optimal safe distance was secured.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.6C
• /
• pp.331-338
• /
• 2008

Soil nailing is used as a method of slope stabilization and excavation support. The design method of soil nail are based on experience or assumption of interaction between soil and reinforcement. Most design methods simply considers the tension of reinforcement for analysis of slope stabilization. Soil nails interact with soils under combined loading of shear and tension. Jewell & Pedley suggested a design equation of shear force with bending stiffness and discussed that the magnitude of the maximum shear force is small in comparison with the maximum axal force. However, they have used a very conservative limiting bearing stress on nails. This paper discusses that the shear strength of soil nails should not be disregarded with proper bearing stresses on nails. The modified FHWA design method was proposed by considering shear forces on nails with bending stiffness.

• Journal of Ocean Engineering and Technology
• /
• v.28 no.4
• /
• pp.274-279
• /
• 2014

This paper investigates the line dynamic forces connecting tugs and a floater, where the planar motion of the floater is due to the weather criteria during the position keeping of the offshore structure by tugs. The analysis situation consists of the position keeping states for the seabed mooring line connection work of the offshore structure at the offshore site. Specifically, the decision about the tug power capacity for the position keeping is essential and depends on the weather criteria, line characteristics, length of line, etc. The planar motion of the structure is constrained by the interference of the installation vessel's operational range, behavior of the underwater fairlead, and other surrounding structures. In this paper, the tug line forces and planar motion of an offshore structure are summarized dependent on the tug line length and line material characteristics in the states fora given floater draft and weather criteria. The tug line dynamic forces and planar motion evaluated here will be used to determine the proper tug power and clearance of an offshore structure.

• Aerospace Engineering and Technology
• /
• v.9 no.2
• /
• pp.168-175
• /
• 2010

During feeding oxidizer to the engine, vortices are occurred at lower dome of oxidizer tank inside by various working environments and external forces for liquid propellant feeding system of space launch vehicle. To eliminate the vortices or swirls Anti-Vortex Devices(AVD) shall be installed at inside lower oxidizer tank. Using the numerical analysis, we have confirmed the performance of AVD and analyzed the mass flow rate by feeding time and magnitudes of swirls on the free surface of oxidizer or exit surface according to the AVD number and length. Then we could derive the optimal design of the AVD number and length.