• Journal of Bio-Environment Control
• /
• v.18 no.4
• /
• pp.354-362
• /
• 2009

This study was performed to develop a suitable nutrient solution for standard rose substrate culture in a closed hydroponic system. 1/4, 1/2, 2/3 and 1 strength of the nutrient solution made by Japan National Institute of Vegetable and Tea Science (JNIVT) were supplied. The photosynthesis rate, quality and growth of cut flower were higher in the 1/2 and 2/3 strength of nutrient solution during high and low temperature period. Based on the above results, optimum nutrient solutions (UOS) were composed by nutrientwater (n/w) absorption ratio with 1/2S ($NO_{3^-}N$ 6.8, $NH_{4^-}N$ 0.7, $PO_{4^-}P$ 2.0, K 3.8, Ca 3.0, Mg 1.2, $SO_{4^-}S$ $1.2me{\cdot}L^{-1}$) at high temperature season and 2/3($NO_{3^-}N$ 9.7, $NH_{4^-}N$ 0.8, $PO_{4^-}P$ 2.2, K 5.0, Ca 3.9, Mg 1.5, $SO_{4^-}S$ $1.5me{\cdot}L^{-1}$) at low temperature season. The results of suitability examination showed that the EC level in newly composed nutrient solution (UOS) was more stable than other nutrient solutions due to its large amount of calcium and potassium. The growth of cut flower cultivated with UOS was higher than those of other nutrient solutions. Especially, the yield of cut flowers in UOS nutrient solution increased 1.4 times than that of other nutrient solution treatments. Consequently, the new nutrient solution investigated in this experiment was suitable for rose cultivation in a closed hydroponic system.

• Journal of Radiation Protection and Research
• /
• v.10 no.1
• /
• pp.50-63
• /
• 1985

A derivation of new release limit, named Derived Release Limit(DRL), into the atomsphere from a reference nuclear power plant has been performed on the basis of the new system of dose limitation recommended by the ICRP, instead of the (MPC)a limit which has been currently used until now as a general standard for radioactive effluents in Korea. In DRL Calculation, a Concentration Factor Method was applied, in which the concentrations of long-term routinely released radionuclides were in equilibrium with dose in environment under the steady state condition. The analytical model used in the exposure pathway analysis was the one which has been suggested by the USNRC and the exposure limits applied in this analysis were those recommended by the USEPA lately. In the exposure pathway analysis, all of the pathways are not considered and some may be excluded either because they are not applicable or their contribution to the exposure is insignificant compared with other pathways. In case, the environmental model developed in this study was applied to the Kori nuclear power plant as the reference power plant, the highest DRL value was calculated to be as $9.10{\times}10^6Ci/yr$ for Kr-85 in external whole body exposure from the semi-infinite radioactive cloud, while the lowest DRL value was observed 3.64Ci/yr for Co-60 in external whole body exposure from the contaminated ground, by the radioactive particulates. The most critical exposure pathway to an individual in the unrestricted area of interest (Kilchun-Ri, 1.3 km to the north of the release point) seems to be the exposure pathway from the contaminated ground and the most critical radionuclide in all pathways appears to be Co-60 in the same pathway. When comparing the actual release rate from KNU-l in 1982 with the DRL's obtained here the release of radionuclides from KNU-1 were much lower than the DRL's and it could be conclued that the exposure to an individual had been kept below the exposure limits recommended by the USEPA.

• Economic and Environmental Geology
• /
• v.38 no.2 s.171
• /
• pp.177-185
• /
• 2005

Data from 122 pumping tests were obtained from 100 boreholes in granites, volcanic rocks, metamorphic rocks, and Cretaceous and Tertiary sedimentary rocks, and then were analyzed using AQTESOLV. Results from 86 of the 122 tests ($71\%$) have an analytical solution corresponding to Theis (1935), Cooper-Jacob (1946), Papadopulos-Cooper (1967), Hantush (1962), Moench (1985), or Hantush-Jacob (1955), whereas the remaining 36 results ($29.5\%$) do not correspond to any of the analytical methods. Of the 86 results, only 17 match the Theis and Cooper-Jacob methods, indicating that the basic methods fer pumping test analysis are useful far only $14\%$ of the total data. This suggests that analytical solutions derived using leaky boundary conditions are appropriate for the analysis of pumping test data in fractured aquifers in this study. Furthermore, the results show the importance of carefully selecting an appropriate model for the analysis of pumping test data. Results from the 122 pumping tests were also analyzed using the GRF model. Using the Barker method, the results show that 77 of the 122 tests ($63\%$) have dimensions ranging between 1.1-2.9. Of these 77 solutions, ($39(44.2{\%})$) have a fractional dimension of 1.1-1.9, ($26(6.5{\%})$) show 2-dimensional radial flow also applicable to the Theis method, and ($38(49.3{\%})$) have dimensions of 2.1-2.9. The results show that groundwater flows according to a fractional flow dimension in fractured aquifers.

• Korean Journal of Food Science and Technology
• /
• v.43 no.2
• /
• pp.243-248
• /
• 2011

The prevalence and distribution of hazardous microorganisms were investigated from the major perilla cultivation area at Milyang, Gyeongnam province, Korea. Aerobic plate count (APC) and coliform count of perilla leaves were 4.82 log CFU/g and 3.85 log CFU/g, respectively. E. coli, S. aureus and B. cereus were detected in 3.0% (4/114), 7.9% (9/114) and 46.5% (53/114) of examined perilla leaves. However, E. coli O157:H7, Salmonella spp, and L. monocytogenes were not detected. The distribution of hazardous microorganisms in perilla leaf cultivation environment were compared and the concentration of APC and coliform counts were more than 3.0 log CFU/(mL, g, $100cm^2$, hand) from most of the samples. S. aureus were detected from irrigation water, packing table, packing vinyl, hand, and clothes. Also, B. cereus was frequently detected from the examined samples. Especially, packing table and collection container were contaminated with maximum 5.5 log $CFU/100cm^2$ of B. cereus. Good Agricultural Practice (GAP) system should be introduced to farms to enhance the safety of perilla leaves.

• Journal of Environmental Policy
• /
• v.9 no.2
• /
• pp.3-19
• /
• 2010

Anyang-cheon(stream) runs through southern metropolitan area of Seoul to Han-river in Korea. Due to fast growth of Seoul, the water quality and quantity problems in Anyang-cheon have occurred. To cope with the problems, the Integrated Watershed Management program for Anyang-cheon was adopted and a KRW 26.1 billion (USD 21.8 million) pilot project (construction of 4 facilities such as reservoir) is suggested for 4 sub-watersheds of Anyang-cheon, which cost will be shared by the 12 local governments (LG). Three cost division schemes are compared. By Scheme 1, if the cost is borne by the LG in a watershed where the facilities are constructed (no cost division scheme), the LG in I is to bear 0.58% of the total construction cost, LG in watershed II 29.54%, LG in IV 0%, LG in V 69.88%. In particular, LG in IV in this scheme bears no cost because no facility is constructed, even though watershed IV is the major beneficiary of the facility construction. Scheme 2 is to share the cost by length of streams in each sub-watershed and the suggested cost share for each sub-watershed is 13.76% by I, 7.34% by II, 45.87% by IV, and 33.03% by V. However, this cost division scheme is fair only under the false assumption that the bargaining powers of group of LGs are identical. To suggest a better and fair division rule, Shapley Value, a cooperative game solution, is used to suggest Scheme 3. In Scheme 3, Shapley Value measures the summation of average marginal contribution of each player in all possible coalitions as cost division scheme and is known to provide a fair division considering bargaining power. In the context of Anyang-cheon, LGs in upper stream have superior bargaining position. The result suggests the cost division is fair under Scheme 3, when the cost shares are 0.29% by I, 14.77% by II, 50% by IV, and 34.94% by V, respectively.

• Korean Journal of Soil Science and Fertilizer
• /
• v.37 no.2
• /
• pp.66-73
• /
• 2004

As one of the typical farming practices in the sloped upland in Pyeongchang and Hongcheon area, application of piling with coarse saprolite materials has been practiced by farmers for several reasons such as reduction of damage by monocropping, better development of plant roots, and better drainage. However, adverse effect on application of coarse saprolite soil materials to environmental aspects should not be ignored. Therefore, this research was conducted to evaluate the physicochemical properties of coarse saprolite materials in upland fields in Pyeongchang area. According to particle size distribution of coarse saprolite materials, averaged gravel contents for Pyeongchang and Hongcheon county were 16.7 and 25.3%, respectively. There was no significant difference in gravel contents by soil depth, and CV values for each particle size ranged from 20 to 40%, which implied that application of coarse material with similar properties. When we compared CEC values of dressed soil with or without considering gravel content, CEC values decreased as increasing gravel contents. The penetration resistances were 0.04-7.48 MPa at the 0 to 10 cm surface soil, and 0.10 to 8.80 MPa at the depth below 11 cm. The bulk density of the soil was $1.15g\;cm^{-3}$ at the surface soil and 1.29 to $1.35g\;cm^{-3}$ at the soil depth below 10 cm. The organic matter content, cation exchange capacity, and avaliable $P_2O_5$ concentrations of soil in upland where piling with saprolite materials of Pyeongchang area applied were $12.4g\;kg^{-1}$, $7.1cmol_c\;kg^{-1}$, and $526mg\;kg^{-1}$, respectively. Cation exchange capacity was lower than that of averaged Korean upland soil, while available $P_2O_5$ concentration was relatively higher than that of averaged Korean upland, which indicated high input of various fertilizers.

• Journal of the Korean Society of Radiology
• /
• v.12 no.3
• /
• pp.409-415
• /
• 2018

The development of smart devices has brought about significant changes in daily life and one of the most significant changes is the virtual reality zone. Virtual reality is a technology that creates the illusion that a 3D high-resolution image has already been created using a display device just like it does in itself. Unrealized subjects are forced to rely on audiovisual materials, resulting in a decline in the concentration of practices and the quality of classes. It used virtual reality to develop effective teaching materials for radiology students. In order to produce a video clip bridge using virtual reality, a radiology clinic was selected to conduct two exposures from July to September 2017. The video was produced taking into account the radiology and work flow chart and filming was carried out in two separate locations : in the computerized tomography unit and in the LINAC room. Prior to filming the scenario and the filming route were checked in advance to facilitate editing of the video. Modeling and mapping was performed in a PC environment using the Window XP operating system. Using two leading virtual reality camera Gopro Hero, CC pixels were produced using a 4K UHD, Adobe, followed by an 8 megapixel resolution of $3,840{\times}2,160/4,096{\times}2,160$. Total regeneration time was performed in about 5 minutes during the production of using virtual reality to prevent vomiting and dizziness. Currently developed virtual reality radiation and educational contents are being used to secure the market and extend the promotion process to be used by various institutions. The researchers will investigate the satisfaction level of radiation and educational contents using virtual reality and carry out supplementary tasks depending on the results.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.10 no.2
• /
• pp.67-85
• /
• 2007

A three-dimensional hydrodynamic model with the fine grid is applied to simulate the barotropic tides, tidal currents, residual currents and salinity dispersions in the Yellow Sea and the East China Sea. Data inputs include seasonal hydrography, mean wind and river input, and oceanic tides. Computed tidal distributions of four major tides($M_2,\;S_2,\;K_1$ and $O_1$) are presented and results are in good agreement with the observations in the domain. The model reproduces well the tidal charts. The tidal residual current is relatively strong around west coast of Korea including the Cheju Island and southern coast of China. The current by $M_2$ has a maximum speed of 10 cm/s in the vicinity of Cheju Island with a anti-clockwise circulation in the Yellow Sea. General tendency of the current, however, is to flow eastward in the South Sea. Surface residual current simulated with $M_2$ and with $M_2+S_2+K_1+O_1$ tidal forcing shows slightly different patterns in the East China Sea. The model shows that the southerly wind reduces the southward current created by freshwater discharge. In summer during high runoff(mean discharge about $50,000\;m^3/s$ of Yangtze), low salinity plume-like structure(with S < 30.0 psu) extending some 160 km toward the northeast and Changjiang Diluted Water(CDW), below salinity 26 psu, was found within about 95 km. The offshore dispersion of the Changjiang outflow water is enhanced by the prevailing southerly wind. It is estimated that the inertia of the river discharge cannot exclusively reach the around sea of Cheju Island. It is noted that spatial and temporal distribution of salinity and the other materials are controlled by mixture of Changjiang discharge, prevailing wind, advection by flowing warm current and tidal current.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.18 no.4
• /
• pp.304-309
• /
• 2015

To evaluate the degree of contamination caused by oil spill accident in the sea, the in-situ sensors which are based on the scientific method are needed in the real site. The sensors which are based on the fluorescence detection theory can provide the useful data, such as the concentration of oil. However these kinds of sensors commonly are composed of the ultraviolet (UV) light source such as UV mercury lamp, the multiple excitation/emission filters and the optical sensor which is mainly photomultiplier tube (PMT) type. Therefore, the size of the total sensing platform is large not suitable to be handled in the oil spill field and also the total price of it is extremely expensive. To overcome these drawbacks, we designed the fluorimeter for the oil spill detection which has compact size and cost effectiveness. Before the detail design process, we conducted the experiments to measure the excitation and emission spectrum of oils using five different kinds of crude oils and three different kinds of processed oils. And the fluorescence spectrometer were used to analyze the excitation and emission spectrum of oil samples. We have compared the spectrum results and drawn the each common spectrum regions of excitation and emission. In the experiments, we can see that the average gap between maximum excitation and emission peak wavelengths is near 50 nm for the every case. In the experiment which were fixed by the excitation wavelength of 365 nm and 405 nm, we can find out that the intensity of emission was weaker than that of 280 nm and 325 nm. So, if the light sources having the wavelength of 365 nm or 405 nm are used in the design process of fluorimeter, the optical sensor needs to have the sensitivity which can cover the weak light intensity. Through the results which were derived by the experiment, we can define the important factors which can be useful to select the effective wavelengths of light source, photo detector and filters.

• Journal of KIISE:Computer Systems and Theory
• /
• v.33 no.4
• /
• pp.242-255
• /
• 2006

In the recent years, Popularization of mobile devices such as Smart Phones, PDAs and MP3 Players causes rapid increasing necessity of Power management technology because it is most essential factor of mobile devices. On the other hand, despite low price, hard disk has large capacity and high speed. Even it can be made small enough today, too. So it appropriates mobile devices. but it consumes too much power to embed In mobile devices. Due to these motivations, in this paper we had suggested methods of minimizing Power consumption while playing multimedia data in the disk media for real-time and we evaluated what we had suggested. Strict limitation of power consumption of mobile devices has a big impact on designing both hardware and software. One difference between real-time multimedia streaming data and legacy text based data is requirement about continuity of data supply. This fact is why disk drive must persist in active state for the entire playback duration, from power management point of view; it nay be a great burden. A legacy power management function of mobile disk drive affects quality of multimedia playback negatively because of excessive I/O requests when the disk is in standby state. Therefore, in this paper, we analyze power consumption profile of disk drive in detail, and we develop the algorithm which can play multimedia data effectively using less power. This algorithm calculates number of data block to be read and time duration of active/standby state. From this, the algorithm suggested in this paper does optimal scheduling that is ensuring continual playback of data blocks stored in mobile disk drive. And we implement our algorithms in publicly available MPEG player software. This MPEG player software saves up to 60% of power consumption as compared with full-time active stated disk drive, and 38% of power consumption by comparison with disk drive controlled by native power management method.