• Korean Chemical Engineering Research
• /
• v.49 no.2
• /
• pp.238-243
• /
• 2011

In this study, we attempted a structural analysis in order to design a balloon type extracorporeal membrane oxygenator that can induce blood flow without using blood pumps for the purpose of complementing the weakness in the existing extracorporeal membrane oxygenator. To analyze the flow characteristic of the blood flow within the virtual model of extracorporeal membrane oxygenator, computational fluid dynamics(CFD) modeling method was used. The operating principle of this system is to make the surface of the extracorporeal membrane oxygenator keep contracting and dilating regularly by applying pressure load using a balloon, and the 'ime Function Value'that changes according to the time was applied by calculating a half cycle of sine waveform and a cycle of sine.waveform Under the assumption that the uni-directional blood flow could be induced if the balloon type extracorporeal membrane oxygenator was designed as per the method described above, we conducted a structural analysis accordingly. We measured and analyzed the velocity and pressure of blood flow at both inlet and outlet of the extracorporeal membrane oxygenator through CFD simulation. As a result of the modeling, it was confirmed that there was a flow in accord with the direction of the blood by the contraction/dilation. With CFD simulation, the characteristics of blood flow can be predicted in advance, so it is judged that this will be able to provide the most optimized design in producing an extracorporeal membrane oxygenator.

• Journal of the Korea Concrete Institute
• /
• v.25 no.6
• /
• pp.613-620
• /
• 2013

Concrete has been recognized as a material which is resistant to high temperatures, but chemicophysical property of concrete is changed by the high temperature. So, mechanical properties of concrete may be reduced. Because of this, standards and researches on the degradation of the mechanical properties of concrete at high temperatures have been presented. However, research data about the state that considering the loading condition and high-strength concrete is not much. Therefore, this study evaluated the high-temperature properties of high-strength concrete by loading condition and elevated temperature. The stress-strain, strain at peak stress, compressive strength, elastic modulus, thermal strain and the transient creep are evaluated under the non-loading and $0.25f_{cu}$ loading conditions on high strength concrete of W/B 12.5%, 14.5% and 20%. Result of the experiment, decrease in compressive strength due to high temperature becomes larger as the compressive strength increases, and residual rate of elastic modulus and compressive strength is high by the shrinkage caused by loading and thermal expansion due to high temperature are offset from each other, at a temperature above $500^{\circ}C$.

• The Journal of the Korea Contents Association
• /
• v.11 no.2
• /
• pp.341-352
• /
• 2011

The purpose of this study was carried out to investigate the effect of electroacupuncture on reactive gliosis expressing GFAP in rat with transient global cerebral ischemia. Subjects were randomly divided into two groups, a control group and a electroacupuncture group on ST36, LI11 and SP9 with 2 Hz and 1 mA. The rats were sacrificed on 1, 3 and 7 days after transient cerebral ischemia using ligation of left common carotid artery. After making brain slide sections, they were immunostained with GFAP antisera(1:2,500). The results were as follows: The numbers of astrocytes of electroacupuncture group were decreased than those of control group at every 1, 2 and 7 days. Especially, the numbers of astrocytes at 3 days(p<0.01) and 8 days(p<0.05) were different statistically. And astrocytes had resting, hypertrophic and moving types on cerebral cortex. The decrease of numbers of astrocytes expressing GFAP showed that electroacupuncture could localise and minimize the brain damage by transient cerebral ischemia and cause brain cell plasticity.

• Journal of the Korean Applied Science and Technology
• /
• v.29 no.1
• /
• pp.108-115
• /
• 2012

Archaeological waterlogged woods found under the sea, in lakes, or in swamp environments are generally weak and fragile. If waterlogged wood materials were taken out of the water and left without modification, they would collapse and lose their original dimensions completely. Conservation is performed to replace the water with chemical agents and to give dimensional stabilization and durability. EDTA and PEG are the most commonly used in the preservation of wood. pH control-precipitation method is used for recovery of EDTA from waste fluid of archeological waterlogged wood conservation treatment. The black substance is eliminated from wood as Fe-EDTA complex are formed and EDTA is separated and precipitated from Fe-EDTA complexes at pH 2.68 or less. The result of analysis of the precipitated products and the commercial EDTA by FT-IR and FE-SEM showed that precipitated product by pH adjusted was not a type of Fe-EDTA complex, but pure EDTA. Waste fluid produced in PEG treatment shows the black color and has an offensive odor by organic matter extracted from wood. Color of waste fluid is decolored with oxidation reaction by peroxy hydrate. In FT-IR and SEM-EDX of PEG after freeze-drying process, no significant change of functional groups induced from oxidation is observed, and any metal ion does not exist in the solid PEG specimen. The molecular weight of PEG is measured using GPC and viscometry. Properties of PEG before and after preservation treatment, and after oxidation with $H_2O_2$ were not changed. Consequently, the peroxidation with $H_2O_2$ is a reasonable and simple method to decolor the used PEG solution.

• Resources Recycling
• /
• v.11 no.2
• /
• pp.36-44
• /
• 2002

The waste garnet powder as a raw material for clay bricks was studied its recycling. The physical strength of clay bricks are closely dependent both on the contents of $SiO_2$, $Al_2$$O_3$, and $Fe_2$$O_3$in clay and on the viscosity of it. Although the garnet power has very high contents of $SiO_2$, $Al_2$$O_3$, and $Fe_2$$O_3$, it could not substituted to clay because of its low viscosity. Therefore the substitution of sand with waste garnet powder was considered to influence positively on the strength of clay bricks .Mixing ratios of {clay-sand}, {sand-garnet powder}, and {clay-sand-garnet powder} based on weight were controlled in the production of clay bricks. The properties of clay bricks such as compression strength, moisture absorption, shrinkage, and specific gravity has been evaluated. It was shown that the optimal mixing combination was found to be { clay(50%)-sand(30%)-garnet powder(20%)} as a weight basis. The present study indicated possibilities to produce commercially clay bricks with the waste garnet powder. An economical benefit will be produced in viable in view of recycling waste garnet powder.

• Applied Chemistry for Engineering
• /
• v.25 no.2
• /
• pp.181-187
• /
• 2014

In order to use the spherical atomizing reduction steel slag (ladle furnace slag, LFS) instead of the fine aggregate of polymer concrete composites, various specimens were prepared with various replacement ratios of atomizing reduction steel slag and the addition ratios of polymer binder. Physical properties of these specimens were investigated through the absorption test, the compressive strength test, the flexural strength test, the hot water resistance test, the pore analysis and the micro-structure using scanning electron microscope. Results showed that the compressive strength and flexural strength of specimens with 7.5% of polymer binders increased with the increase of replacement ratios of atomizing reduction steel slag, but those of the specimens with 8.0% or more of polymer binders showed a maximum strength at a certain replacement ratio due to the material segregation causing the increase of fluidity. By hot water resistance tests, the compressive strength, flexural strength, average pore diameter, and bulk density decreased but the total pore volume and pore diameter increased. It was concluded that the amount of polymer binders could be reduced by maximum 23.8%, because the workability of the polymer concrete was remarkably improved by using the atomizing reduction steel slag instead of fine aggregate. However, since the use of atomizing reduction steel slag decreased the resistance of the polymer concrete to hot water, further studies are required.

• Food Science of Animal Resources
• /
• v.25 no.2
• /
• pp.121-126
• /
• 2005

The changes in quality characteristics and shelf-life of vacuum-shrink packaged Bierschinken after stuffing in fibrous casing and stored at 5 and $10^{\circ}C$ were investigated The total aerobic plate count (APC) of Bierschinken was initially <2.00 $log_{10}CFU/cm^2$, however increased gradually over storage period The APCs of Bierschinken maintained at the level of 4.86 and 5.13 $log_{10}CFU/cm^2$ after 35 days at 5 and $10^{\circ}C$, respectively. pH tended to decrease with the extension of storage period The values of TBA and VBN tended to increase with storage time, of which trend was pronounced at $10^{\circ}C$ rather than at $5^{\circ}C$. According to the sensory evaluation, Bierschinken had the marketing value till 28 days irrespective of storage temperature. The shelf-life of Bierschinken tested might be preferentially restricted by the occurrence of off-odor and off-flavor at the end of storage period.

• Applied Chemistry for Engineering
• /
• v.25 no.4
• /
• pp.380-385
• /
• 2014

Spherical atomizing reduction steel slag was prepared by atomizing technology using reduction steel slag (ladle furnace slag, LFS) generated from steel industry. In order to develop the mass-recycling technology of atomizing reduction steel slag, polymer concrete composite was prepared using spherical atomizing reduction steel slag instead of fine aggregate (river sand) and coarse aggregate (crushed aggregate), depending on the grain size. Different polymer concrete specimens were prepared with the various proportions of polymer binder and replacement ratios of atomizing reduction steel slag in order to investigate the characteristics of polymer concrete composite. Results showed that compressive strengths of polymer concrete specimens decreased with the increase of replacement ratios of atomizing reduction steel slag, but flexural strengths of the specimens showed a maximum strength at the 50% of replacement ratios of atomizing reduction steel slag. It was concluded that addition ratio of polymer binder, which affect greatly on the prime cost of production of polymer concrete, could be reduced by maximum 18.2 vol% because the workability of the polymer concrete was remarkably improved by using the atomizing reduction steel slag. However, further study is required because the mechanical strength of the specimen using atomizing reduction steel slag was greatly reduced in hot water resistance test.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.485-488
• /
• 2008

Recycled fine aggregate has low quality because it contains large amount of old mortar. So, its usage is limited to a lower value-add, such as the roadbed material etc. Also, alkaline water occurred from treatment process of the waste concrete is becoming the cause of environmental problem. Accordingly, this study is to develop on the high quality recycled fine aggregate produced by low speed wet abraser using sulphuric. We investigated the properties of compressive strength of the mortar which was manufactured using recycled fine aggregate containing calcined gypsum produced by earlier mentioned process. Test results indicate that mortar using recycled fine aggregate containing calcined gypsum has lowest compressive strength. It seems that low compressive strength is closely associated with the expansion of the specimen by excessive formation of ettringite.

• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.804-809
• /
• 2011

Tubular $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-${\delta}$}$ membranes were prepared by extrusion. TGA results of green body membrane after extrusion showed three successive weight losses due to decomposition of organic additives and carbonate. Drying shrinkage rate of tubular $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-${\delta}$}$ membranes was no change after 68 h and higher in the membrane with large outer diameter. XRD and SEM results showed the sintered membranes were the single phase structure and dense. The stoichiometric molar ratio agreed well with composition ratio calculated by EDS results for $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-${\delta}$}$ membrane. Radial crushing strength of tubular $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-${\delta}$}$ membrane with 0.95 mm thickness was 5.7 kgf/$mm^2$ and the oxygen permeation rate of same membrane was 146.85 mL/min ($Jo_2$=2.33 mL/$min{\cdot}cm^2$) at $950^{\circ}C$. Therefore, it was known that use of vacuum pump was more effective than that of sweep gas to obtain higher oxygen permeation flux.