• Proceedings of the Korea Crystallographic Association Conference
• /
• 2002.11a
• /
• pp.16-16
• /
• 2002

The presently commercialized lithium-ion batteries use layer structured LiCoO₂ cathodes. Because of the high cost and toxicity of cobalt, an intensive search for new cathode materials has been underway in recent years. Recently, a concept of a one-to-one solid state mixture of LiNO₂ and LiMnO₂, i.e., Li[Ni/sub 0.5/Mn/sub 0.5/]O₂, was adopted by Ohzuku and Makimura to overcome the disadvantage of LiNiO₂ and LiMnO₂. Li[Ni/sub 0.5/Mn/sub 0.5/]O₂ has the -NaFeO₂ structure, which is characteristic of the layered LiCoO₂ and LiNiO₂ structures and shows excellent cycleability with no indication of spinel formation during electrochemical cycling. Layered Li[Ni/sub x/Co/sub 1-2x/Mn/sub x/]O₂ (x = 0.5 and 0.475) materials with high homogeneity and crystallinity were synthesized using a mechanical alloying method. The Li[Ni/sub 0.475/Co/sub 0.05/Mn/sub 0.475/]O₂ electrode delivers a high discharge capacity of 187 mAh/g between 2.8 and 4.6 V at a high current density of 0.3 mA/㎠(30 mA/g) with excellent cycleability. The charge/discharge and differential capacity vs. voltage studies of the Li[Ni/sub x/Co/sub 1-2x/Mn/sub x/]O₂ (x = 0.5 and 0.475) materials showed only one redox peak up to 50 cycles, which indicates that structural phase transitions are not occurred during electrochemical cycling. The magnitude of the diffusion coefficients of lithium ions for Li[Ni/sub x/Co/sub 1-2x/Mn/sub x/]O₂(x = 0.5 and 0.475) are around 10/sup -9/ ㎠/s measured by the galvanostatic intermittent titration technique (GITT).

• Polymer(Korea)
• /
• v.33 no.3
• /
• pp.203-206
• /
• 2009

Polyaniline Emeraldine salt (PANI-salt) prepared by the common chemical oxidative polymerization caused the corrosion of the metallic injection mold by protonic acid such as HCl which used as a dopant. PANI-salt, polyaniline doped with dodecylbenzenesulfonic acid (DBSA), was obtained by the emulsion polymerization in nonpolar organic solvent, toluene. In this study DBSA was used as a dopant along with a surfactant. PANI-salt and high impact polystyrene (HIPS) have a good solubility in toluene. Blends with different ratio of PANI and HIPS were prepared through a solution-cast blending. The structure of PANI-salt was characterized by FT-IR and UV-Vis. The morphology, thermal, and electrical properties for PANI-HIPS blends were investigated. Injection molded under $103^{\circ}C$, 120 psi, PANI-HIPS showed the highest electrical conductivity ($6.02{\times}10^{-5}\;S/cm$) after blending PANI (50 mL) and HIPS (1 g).

• Journal of Life Science
• /
• v.18 no.3
• /
• pp.298-303
• /
• 2008

Using a phage peptide library approach, we have isolated a peptide ligand that binds to transferrin receptor on the surface of human melanoma cell, B16F10. The library was first screened twice by recovering internalized phages and was further screened three times by competitively eluting transferrin receptor-specific phages with human transferrin among the phages bound to the cell surface. The peptides displayed by the selected phages were fused to translocation and catalytic domain of Pseudomonas exotoxin to prepare recombinant toxins. After estimating cytotoxicity of each recombinant toxin toward B16F10 cell, seven clones were selected. Sequence analysis revealed that one of the clones displayed a peptide which had a significant sequence homology with human transferrin. The peptide was chemically synthesized and was shown to be functional in delivering cytotoxic agents into B16F10 cell via interaction with transferrin receptor.

• Elastomers and Composites
• /
• v.49 no.3
• /
• pp.199-203
• /
• 2014

Terpolymer syrups were photopolymerized from 2-ethylhexyl acrylate, 2-hydroxylethyl acrylate and isobornyl acrylate to prepare acrylic pressure sensitive adhesives (PSAs). After polymerization, various crosslinkers as 1,6-hexanediol diacrylate (HDDA), poly (ethylene glycol) diacrylate (PEGDA, Mn = 250, 575, and 700) were added and then UV-irradiated to prepare the semi-IPN type PSAs. Their adhesion performance and storage modulus (G') were strongly dependent on their chemical structure and molecular weight of the crosslinkers. Optical properties such as transmittance (> 92.5 %), haze (< 1.0 %) and color-difference (< 0.3) of PSAs samples were not affected by crosslinker types used in this study.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1995.04a
• /
• pp.52-53
• /
• 1995

현재 상용화 되어있는 산소/질소 분리용 고분자 분리막은 비교적 낮은 선택도를 가지고 있다. 즉, 이점은 확산도와 용해도를 조절함으로써 분리막의 투과선택도를 높일 수 있는 가능성을 보여주고 있으며 보다 높은 투과도와 투과선택도를 갖는 새로운 고분자 재료의 선택이 분리막을 통한 기체 분리나 그 상업적 이용에 절실히 요구되고 있다. PSf는 상용성, 화학적 내구력, 강도, 높은 유리전이온도와 우수한 기체투과성질을 가진 고분자로 분리막에 많이 응용되고 있다. Erb 등은 용매로 DMF(dimethylformamide)와 THF(tetrahydrofuran)를 사용하여 막을 제조하였다. 상부 흐름압력이 5atm일때 각 기체의 투과도 계수는, 헬륨이 11, 이산화탄소가 5.5, 메탄이 0.5, 질소가 0.2였으며, PSf막에 대한 각 기체의 투과는 Henry mode보다 Langmuir mode에서 더욱 우세하게 일어난다고 생각하였다. 또한 Ghosal 등은 PSf에 nitro기를 도입한 nitrated PSf의 투과특성을 조사하였다. 실험결과 nitro group이 치환된 PSf막이 nitro group이 없는 막에 비해 투과도는 낮았지만 선택도는 증가하였다. 구조가 다른 여러가지의 PSf막을 통한 기체 투과성질은 Ghem 등에 의해 밝혀졌다. Membrane-covered probes를 이용한 폴라로그램(polarogram) 방법은 산소를 측정하는데 가장 보편적인 방업ㅂ으로, 산소 탐침(oxygen probe)의 원리는 소위 효소 전극을 발전시키는데 이용되어 왔다. 효소전극은 산소와 실험하고자 하는 물질간의 특정한 효소반응에 기초를 둔 다양한 물질의 선택적 측정을 위한 것이다. 이때 센서에 응용되는 합성막은 산소에 대해 선택적인 투과를 해야하며, 상대적으로 높은 산소확산계수와 물에 대해서는 낮은 투과도를 가져야 한다. 높은 산소확산계수는 반응을 빠르게 하는 잇점이 있으며 물에 대한 낮은 투과도는 센서내의 전해질 물질을 유지보호하는 역할을 한다. 분리막이 산소전극에 이용될 경우 높은 산소 확산계수 이외에도 적절한 기계적 강도, 열적 안정성 등이 요구된다.

• Korean Journal of Microbiology
• /
• v.38 no.2
• /
• pp.96-102
• /
• 2002

The S-phase checkpoint mechanisms response to DNA damage or inhibition of DNA replication for maintenance of genetic stability in eukaryotic cells. These roles include cell cycle control arrest at S-phase and Iranscriptional induction of repair genes. To characterize the defects of dpbll mutant for both these responses, we examined the over-expression effect of DPBll gene, the sensitivity to HU, MMS, and the transcriptional pattern by DNA damage agent for RNRS mRNA. RNRS transcript is induced in response to a wide variety of agents that either damage D7A directly through chemical modification or induce stress by blocking DNA synthesis. As results, dpbll-1 cells are sensitive to DNA damage agents and the level of RNR3 mRNA is reduced approximately 40% than wild type cells. Moreover, we found the same results in dpb2-1 cells. Therefore, we propose that DPB2 and DPBll act as a sensor of replication that coordinates the transcriptional and cell cycle responses to replication blocks.

• Journal of Powder Materials
• /
• v.19 no.3
• /
• pp.210-214
• /
• 2012

Mass production-capable $Li_2MnSiO_4$ powder was synthesized for use as cathode material in state-of-the-art lithium-ion batteries. These batteries are main powder sources for high tech-end digital electronic equipments and electric vehicles in the near future and they must possess high specific capacity and durable charge-discharge characteristics. Amorphous silicone was quite superior to crystalline one as starting material to fabricate silicone oxide with high reactivity between precursors of sol-gel type reaction intermediates. The amorphous silicone starting material also has beneficial effect of efficiently controlling secondary phases, most notably $Li_xSiO_x$. Lastly, carbon was coated on $Li_2MnSiO_4$ powders by using sucrose to afford some improved electrical conductivity. The carbon-coated $Li_2MnSiO_4$ cathode material was further characterized using SEM, XRD, and galvanostatic charge/discharge test method for morphological and electrochemical examinations. Coin cell was subject to 1.5-4.8 V at C/20, where 74 mAh/g was observed during primary discharge cycle.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.8 no.1
• /
• pp.49-56
• /
• 2010

In the pyroprocessing of spent nuclear fuels, LiCl-KCl waste salt containing radioactive rare earth chlorides are generated. The radioactive rare earth oxides are recovered by co-oxidative precipitation of rare earth elements. The powder phase of rare eath oxide waste must be immobilized to produce a monolithic wasteform suitable for storage and ultimate disposal. The immobilization of these waste developed in this study involves a solid state sintering of the waste with host borosilicate glass and zinc titanate based ceramic matrix(ZIT). And the rare-earth monazite which synthesised by reaction of ammonium di-hydrogen phosphate with the rare earth oxides waste, were immobilzed with the borosilicate glass. It is shown that the developed ZIT ceramic wasteform is highly resistant the leaching process, high density and thermal conductivity.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.133-133
• /
• 2016

화학저항식(Chemiresistive) 가스센서의 저항변화를 향상시키기 위해서는 센서 소재의 비표면적을 향상시키는 방향 및 전자천이를 증가시키는 방향으로 연구가 진행되어야 하며, 그 중 센서의 비표면적을 향상시키는 예로써 중공 나노섬유가 있을 수 있다. 본 연구에서는 비표면적의 향상뿐만 아니라 중공 나노섬유의 전자천이를 증가시켜 센서의 검출 성능을 더욱 향상시키기 위한 목적으로 $TiO_2/ZnO$ 이중층 중공 나노섬유를 제안하었다. 제안된 $TiO_2/ZnO$ 이중층 중공 나노섬유는 템플레이트 합성법을 통해 제작되었으며, 그 공정은 다음과 같다; 전기방사(Electrospinning) 공정을 통해 폴리머 나노섬유를 제작한 후 $TiO_2$ 층과 ZnO 층을 ALD(Atomic Layer Deposition) 공정을 통해 차례대로 증착시킨다. 그 후 후열처리 공정을 통해 코어 폴리머를 제거함으로써 $TiO_2/ZnO$ 이중층 중공 나노섬유를 얻을 수 있다. 이 때, ZnO 층의 두께는 각각 달리하여 제작되었으며, 최종적으로 이들에 대한 가스 센싱 특성 및 메커니즘에 대한 체계적인 조사를 진행하였다. 단층 중공나노섬유는 셀 층의 두께가 Debye length와 유사할 때 셀 층 표면이 완전공핍층이 형성되고, 그 보다 크게 되면 부분적인 공핍층이 형성되게 되어 감응도가 감소하게 된다. 그러나 이중층 중공 나노섬유의 경우 셀 층의 두께가 Debye length 보다 더 크게 되더라도 TiO2와 ZnO의 헤테로접합으로 인해 ZnO에서 TiO2로 전자의 이동을 야기시키게 되어 환원성 가스에 대한 감응도가 단층 ZnO 중공 나노섬유에 비해 향상되게 된다.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.6
• /
• pp.539-548
• /
• 2016

The non-noble 1D nanofibers(NFs) prepared by electrospinning and calcination method were used as oxygen evolution reaction (OER) electrocatalyst for water electrolysis. The electrospinning process and rate of solution composition was optimized to prepare uniform and non-beaded PVP polymer electrospun NFs. The diameter and morphology of PVP NFs changed in accordance with the viscosity and ion conductivity. The clean metal precursor contained electrospun fibers were synthesized via the optimized electrospinning process and solution composition. The calcined $CuCo_2O_4$ NFs catalyst showed higher activity and long-term cycle stability for OER compared with other $Co_3O_4$, $NiCo_2O$ NF catalysts. Furthermore, the $CuCo_2O_4$ NFs maintained the OER activity during long-term cycle test compared with commercial $CuCo_2O_4$ nanoparticle catalyst due to unique physicochemical and electrochemical properties by1D nanostructure.