• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.6
• /
• pp.639-646
• /
• 2012

The characteristics of autoignited lifted flames in laminar jets of carbon monoxide/hydrogen fuels have been investigated experimentally in heated coflow air. In result, as the jet velocity increased, the blowoff was directly occurred from the nozzle-attached flame without experiencing a stabilized lifted flame, in the non-autoignited regime. In the autoignited regime, the autoignited lifted flame of carbon monoxide diluted by nitrogen was affected by the water vapor content in the compressed air oxidizer, as evidenced by the variation of the ignition delay time estimated by numerical calculation. In particular, in the autoignition regime at low temperatures with added hydrogen, the liftoff height of the autoignited lifted flames decreased and then increased as the jet velocity increased. Based on the mechanism in which the autoignited laminar lifted flame is stabilized by ignition delay time, the liftoff height can be influenced not only by the heat loss, but also by the preferential diffusion between momentum and mass diffusion in fuel jets during the autoignition process.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.1
• /
• pp.75-81
• /
• 2012

Autoignited lifted flames in laminar jets with hydrogen-enriched methane fuels have been investigated experimentally in heated coflow air. The results showed that the autoignited lifted flame of the methane/hydrogen mixture, which had an initial temperature over 920 K, the threshold temperature for autoignition in methane jets, exhibited features typical of either a tribrachial edge or mild combustion depending on fuel mole fraction and the liftoff height increased with jet velocity. The liftoff height in the hydrogen-assisted autoignition regime was dependent on the square of the adiabatic ignition delay time for the addition of small amounts of hydrogen, as was the case for pure methane jets. When the initial temperature was below 920 K, where the methane fuel did not show autoignition behavior, the flame was autoignited by the addition of hydrogen, which is an ignition improver. The liftoff height demonstrated a unique feature in that it decreased nonlinearly as the jet velocity increased. The differential diffusion of hydrogen is expected to play a crucial role in the decrease in the liftoff height with increasing jet velocity.

• Journal of the Korean Institute of Gas
• /
• v.14 no.2
• /
• pp.34-39
• /
• 2010

Flame propagation velocity is the one of the main mechanism of the stabilization of triple flame. To quantify the triple flame propagation velocity, Bilger presents the triple flame propagation velocity through the experiment, depending on the mixture fraction gradient, based on the laminar jet flow theory. However, in spite of these many analyses, there has not been any attempt to quantify the triple flame propagation velocity with the radius of flame curvature. In the present research, a relation of the flame propagation velocity is proposed with the radius of flame curvature for the flame stabilization mechanism. As a result, we have shown that the height of lifted flame is determined with the nozzle diameter and exit velocity of fuel and presented that the radius of flame curvature is proportion to the nozzle exit velocity of fuel and height of lifted flame. Therefore, the importance of the radius of flame curvature has to be recognized. To discribe the flame stabilization mechanism, Bilger's formula has to be modified with flame curvature effect.

• 한국연소학회:학술대회논문집
• /
• 2000.05a
• /
• pp.1-8
• /
• 2000

The effects of nozzle arrangements, nozzle distances and fuel flowrates on the flame stabilities such as flame length, liftoff height and blowout characteristics are investigated experimentally. Three nozzle arrangements - diamond 4 nozzle, linear 5 nozzle, cross 5 nozzle- are used. Flame interactions result in the increase of the blowout flowrates and constant turbulent liftoff heights. The flames separated about 10 nozzle diameters are sustained as nozzle attached flames to the higher fuel flowrates than the other separation cases. Normally flames are extinguished at the lifted states. Blowout flowrates are affected by the nozzle configuration, nozzle seperation distance. Blowout flowrates for the diamond- or cross- shaped nozzle arrangements are parabolic function of nozzle distances. Maximum blowout flowrates for the 5 nozzle configuration case except linear one is about 2.9 times that of single equivalent nozzle case. Turbulent liftoff heights are not function of flowrates for the interacting flames.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.4
• /
• pp.461-466
• /
• 2001

The characteristics of nonpremixed interacting flames are investigated in the parameter of nozzle configuration and nozzle separation distane, s. Three nozzle arrangements - diamond 4 nozzle, linear 5 nozzle and cross 5 nozzle- are used. When s is about 10 nozzle diameter, flames lift from the nozzle at the highest fuel flowrate compared with the other s cases. Normally flames are extinguished at the lifted states. Flowrates when blowout occurs are affected by the nozzle configuration, nozzle seperation distance. Blowout flowrates for the diamond- or cross-shaped nozzle cases are parabolic function of s. For 5 cross nozzle case, flames extinguished at 3.3 times higher flowrate than that of single equivalent area nozzle. Turbulent liftoff heights are not function of flowrates for these cases.

• Journal of the Korean Institute of Gas
• /
• v.12 no.4
• /
• pp.21-28
• /
• 2008

A numerical analysis is achieved to elucidate the behavior of lifted flames and characteristics of flow near flame zone according to the exit velocity of triple flame, Poiseuille and uniform distribution. For the cases of Poiseuille and uniform nozzle exit velocity, we reviewed previous results with the present numerical results and investigated characteristics of the flame structure near the flame zone comparing with liftoff height generalized by momentum flux. In addition, a close inquiry into the combustion flow characteristics near flame zone was made with the characteristics of velocity, pressure, temperature and chemical reaction. From nozzle to flame zone, center line velocity profile traced well with the velocity profile of typical cold jet flow, but very near the flame zone, this study examined phenomenon that flow velocity decreases very quickly before the flame zone and then increases very quickly after the flame zone. Because flame zone acts as a barrier at the flow region which is before the flame zone and accelerate the flow velocity when it pass through the flame zone. This phenomenon was not clarified previous cold jet flow.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.10
• /
• pp.1025-1031
• /
• 2011

Autoignition characteristic is an important parameter for designing diesel or PCCI engines. In particular, diesel spray flames are lifted from the nozzle and the initial flame is formed by an autoignition phenomenon. The lifted nature of diesel spray flames influences soot formation, since air will be entrained into the spray core by the entrainment of air between the nozzle region and the lifted flame base. The objective of the present study was to identify the effect of heat loss on the ignition delay time by adopting a coflow jet as a model problem. Methane ($CH_4$), ethylene ($C_2H_4$), ethane ($C_2H_6$), propene ($C_3H_6$), propane ($C_3H_8$), and normal butane (n-$C_4H_{10}$) fuels were injected into high temperature air, and the liftoff height was measured experimentally. As the result, a correlation was determined between the liftoff height of the autoignited lifted flame and the ignition delay time considering the heat loss to the atmosphere.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.6
• /
• pp.56-63
• /
• 2018

In low swirl combustors the flame is lifted above the nozzle to achieve balance between the flame speed and velocity field at the exit of the nozzle. Characterization of the flame liftoff height is important because it affects the stability of the combustor and degradation of the nozzle material. In experiments, a counter-intuitive trend of flame liftoff heights with respect to inlet velocities was observed. To elucidate the complicated flow field in a low swirl combustor having swirl vanes and a turbulence generator, a series of numerical simulations of non-reacting flows was conducted by varying the inlet velocity. The flow structures at the exit of the nozzle with respect to the inlet velocities are investigated to support the observation in the experiments.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.453-458
• /
• 2001

The stability of turbulent nonpremixed interacting flames is investigated in terms of nozzle configuration shapes which depend on the existence of the center nozzles. Six nozzle arrangements which are cross 4, 5, 8, 9, square 8 and circular 8 nozzles are used for the experiment. Those are arranged to see the effect of the center nozzle out of multi-nozzle. There are many parameters that affect flame stability in multi-nozzle flame such as nozzle separation distance, fuel flowrates and nozzle configuration, but the most important factor is the existence of nozzles in the center area from the nozzle arrangement. As the number of nozzle in the area is reduced, more air can be entrained into the center of flame base and then tag flame is formed. In the case of circular 8 nozzles, blowout flowrates are above 5.4 times compared with that of single equivalent area nozzle.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.3 s.234
• /
• pp.368-375
• /
• 2005

We have presented characteristics of a transitional behavior from a premixed flame to a triple flame in a lifted flame according to the change of equivalence ratio. The experimental apparatus consisted of a slot burner and a contraction nozzle for a lifted flame. As concentration difference of the both side of slot burner increases, the shape of flame changed from a premixed flame to a triple flame, and the liftoff height decreased to the minimum value and then increased again. Around this minimum point, it is confirmed a transition regime from premixed flame to triple flame. Consequently, the experimental results of the liftoff height, flame curvature, and luminescence intensity showed that the stabilized laminar lifted flame regime is categorized by regimes of premixed flame, triple flame and critical flame.