• Cement
• /
• s.127
• /
• pp.61-67
• /
• 1992

• 레미콘
• /
• no.6 s.16
• /
• pp.17-21
• /
• 1988

• 레미콘
• /
• no.1 s.58
• /
• pp.46-56
• /
• 1999

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.1 no.2
• /
• pp.93-100
• /
• 2013

A variety of researches on the concrete with high volume mineral admixture have increased in recent years. In fact, it is very important to find appropriate replacement ratio of concrete with high volume mineral admixture in order to apply in the field. In this study, compressive strength according to fly ash and blast furnace slag replacement ratio as well as curing temperature was measured in the conditions of obtaining the same workability in order to examine the characteristics of concrete with high volume mineral admixture. In conclusion, it was found that the compressive strength at the age of 3 days decreased by 1.4MPa and the compressive strength at the age of 28 days decreased by 3.8MPa when the fly ash replacement ratio increased by 10%. Also, it was found that the compressive strength at the age of 3 days decreased by 1.0MPa and the compressive strength at the age of 28 days decreased by 0.9MPa when the blast furnace slag replacement ratio increased by 10%. Through the tests, we obtained the basic data for developing the future research on the concrete with high volume mineral admixture for housing structure.

• Journal of the Korea Institute of Building Construction
• /
• v.19 no.6
• /
• pp.485-494
• /
• 2019

This study is to evaluate the effect of admixtures such as blast-furnace slag and fly ash on adhesion in flexure and tension of polymer cement mortar(PCM) using SAE emulsion. The test specimens are prepared with five polymer-cement ratios and five admixture contents, and tested for flexural strength, adhesion in flexure, tensile strength and adhesion in tension. Based on the test results, no improvement of flexural strength and adhesion in flexure caused by admixtures in PCM can be indicated, but the tensile strength and adhesion in tension is improved due to mixing of the admixtures. In particular, the maximum of adhesion in tension of PCM with P/C 20% and BF content of 10% is 3.35MPa which is about 2.36 times higher than that of ordinary cement mortar, and 1.32 times that of PCM that does not contain any admixture. The average ratio of adhesion in tension to tensile strength of PCM was 48.7%. It is apparent that admixture contents of 5% or 10% could be proposed for improvement of tensile strength and adhesion in tension of PCM.

• Journal of the Korean Ceramic Society
• /
• v.39 no.2
• /
• pp.126-134
• /
• 2002

Fabrication of mortar containing fly ash for high strength structural material was investigated by using a Mechanochemically Processed Cement (MPC) and/or Fly Ash (MPFA), which was compared to the specimen (at the same fabrication condition of fly ash adding contents (10, 20 and 30 wt%) and curing time (7 and 28 days)) fabricated by using Ball-mill Processed Cement (BPC) and As Received Fly Ash (ARFA) in terms with compressive strength and microstructures. Mortar specimen fabricated by using MPC and ARFA showed 5-11% higher compressive strength than that in the case of using BPC and ARFA, and mortar specimen by using BPC and MPFA represented 10-20% higher compressive strength than that for the case of using BPC and ARFA. Furthermore, mortar specimen fabricated by simultaneously using MPC and MPFA exhibited about 24% higher value of compressive strength than that for the case of using BPC and ARFA, which was considered to be synergic efficiency in increasing compressive strength. Increased compressive strength as above mentioned is considered to be caused by mutually increased affinity between cement and fly ash induced during mechanochemical Processing(MP).

• Journal of the Korea Institute of Building Construction
• /
• v.10 no.5
• /
• pp.95-102
• /
• 2010

In recent years, the demand for the development of high quality and cost effective materials, as well as the competition to ensure a diverse and sufficient amount of ready-mixed concrete, has been increasing rapidly. In this experiment, concretes made with different admixtures are blended with each other in different combinations and ratios, in order to identify potential problems. The first test was a slump level test, in which all of the concretes met the required numbers, as they also did in the test for air content. Plain organic acid concrete scored the highest in bleeding amount, but organic acid mix in general showed a similar outcome. In the early measurement of compressive strength, plain naphthalene concrete was the strongest. Of the blends, the 5:5 mix of organic acid and naphthalene was the strongest. In the standard measurement, the 5:5 mix of naphthalene and lignin was the strongest. Tensile strength tests revealed similar results. Length change rate proved to be greater in blended concrete than in plain concrete, and dry shrinkage rate was highest in the 7:3 ratio blends. Through SEM photo analysis, it was confirmed that the 7:3 ratio blends contained more micro-voids. In conclusion, with the exception of a specific few combinations, it was found that the blending of different types of concrete is undesirable due to the delayed coagulation time as well as the early decrease in strength.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.3
• /
• pp.259-266
• /
• 2018

In recent years, the early strength of concrete is important in order to shorten the time of form removal at the construction site. The purpose of this study is to analyze the moment of form removal as investigating the amount of cement contents and the physical properties and strength of the concrete according to types of admixture in the curing temperature of $10^{\circ}C$ for concrete of 21 to 27 MPa. As a result, it was found that compressive strength of concrete could not be secured 5 MPa by 36 hours even if the amount of cement contents were increased to $360kg/m^3$ with plain admixture. Also, it was confirmed that the strength improvement rate was excellent when using the accelerating agent with polycarboxylic acid type, and the moment of compressive strength of 5 MPa was estimated at 30 hours.

• Applied Chemistry for Engineering
• /
• v.34 no.3
• /
• pp.285-290
• /
• 2023

Poly-lactic acid (PLA) is the most promising polymer in additive manufacturing as an alternative to acrylonitrile butadiene styrene (ABS). Since it is produced from renewable resources such as corn starch and sugar beets, it is also biocompatible and biodegradable. However, PLA has a couple of issues that limit its use. First, it has a comparatively low glass transition temperature of around 60 ℃, such that it exhibits low thermal resistance. Second, PLA has low impact strength because it is brittle. Due to these problems, scientists have found methods to improve the crystallinity and ductility of PLA. Polyethylene glycol (PEG) is one of the most studied plasticizers for PLA to give it chain mobility. However, the blend of PLA and PEG becomes unstable, and phase separation occurs even at room temperature as PEG is self-crystallized. Thus, it is necessary to investigate the optimal mixing ratio of PLA-PEG at the molecular scale. In this study, molecular dynamics will be conducted with various ratios of L-type PLA (PLLA) or DL-type PLA-PEG (PDLA-PEG) systems by using BIOVIA Materials Studio.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.319-320
• /
• 2003

압전성과 초전성을 나타내는 고분자인 poly(vinylidene fluoride)(PVDF)는 poly(methyl methacrylate), poly(vinyl acetate), 및 Poly(vinyl methyl ketone)(PVMK) 등과 블렌딩하면 혼화성(miscibility)이 있다. 이들 블렌드물들을 용융온도 이상으로 승온시키면 낮은 온도에서는 균일상으로 존재하지만, 온도가 계속 증가하면 상분리되어 LCST(lower critical solution temperature)를 나타낸다[1]. 이러한 승온에 의한 상분리 거동에서 외부전장을 가하면 전기활성 고분자인 PVDF에 영향을 주어 상분리 거동이 변화될 것으로 예산된다. (중략)