• Journal of the Korea Organic Resources Recycling Association
• /
• v.6 no.1
• /
• pp.21-30
• /
• 1998

The effects of compost inoculation on the degradation of cellulosic fraction in composting of food waste and paper mixture were investigated by bench-scale composting. With the increase of seed inoculation, the time to reach the peaks of temperature, $CO_2$ evolution rate, and ammonia evolution rate was reduced, indicating that seed compost had beneficial effects on the enhanced degradation of organic materials at the early stage of composting. However, the final conversion of organic matters and the loss of ammonia were not affected by the amount of seed compost inoculated. The increasing of seed inoculum also resulted in the higher level of cellulase activity at initial stages and rapid rise to the maximums, suggesting that initial supply of sufficient cellulolytic microorganisms might facilitate the evolution of cellulase activity. The cellulose was degraded substantially during the increasing phase of cellulase activity, while they showed similar values at the end of 20 days composting. As a result, the seed inoculation seemed to be effective to the enhanced evolution of cellulase activity and cellulose degradation at initial stage of composting. But it did not contribute to increase the final degradation of cellulose after the entire composting reaction of 20 days.

• 한국해양학회지
• /
• v.9 no.2
• /
• pp.52-58
• /
• 1974

The water temperature distribution and the water movement closely related with it, in the east side of Korea, was condidered. Special emphasis was paid on the low temperature phenomenon near Ulgi. It was known from the temperature distribution in the east side of Korea that the Tsushima current continues to flow northward at the surface near Sokcho. Also the influence of the cold water extends from the North to the South with increasing depth. The formation of the cold core near Ulgi was explained as due mainly to the existence of the boundary layer near the surface, and partly to the effect of the wind. This inclination of the boundary layer has the value of about 3.0m/Km, and the lower cold current velocity computed using this value lies in the range of those observed by Nishida(1926, 1927). The upwelling velocity was computed approximately as 1.4 10$\^$-3/ cm/sec, and the maximum distance to which the boundarylayer can rise or fall from it's equilibrium position was considered as below 10m.

• Korean Journal of Soil Science and Fertilizer
• /
• v.23 no.2
• /
• pp.107-113
• /
• 1990

In comparision with calcium sulphate, the effect of calcium-carbonate, -silicate and -hydroxide on desalinization of tidal saline soil was investigated in a continuous leaching column experiments after mixing with an equivalent amount of Ca to sodium plus magnessium in the saline soil. One half of liming materials was mixed to the top one-tenth of column soil and the remainder was spread on the surface. Results obtained are as follows ; 1. Gypsum made easy to percolate and desaline (Na) tidal marine soil but accumulated magnessium in subsoil. 2. $Ca(OH)_2$, $CaCO_3$, and $CaSO_3$ precipitated Mg in the soil which limes were mixed, but they washed down magnessium more severely from the immediate bellow the limed soil and less from the subsequent soil layers. This leaching was more severer at the treatment of $Ca(OH)_2$and lowest at the treatment of $CaSiO_3$. 3. The alkalinity of lime in addition to the dissociation of exchangeable Na raised pH of limed leached tidal soil and slowed down the percolation rate which retarded desalining Na from limed saline soils. This effect was most severe in the $Ca(OH)_2$ treated soil. 4. pH of leached soils was correlated possitively with exchangeable Na and negatively with exchangeable Mg giving follwing relationship pH= 7.77+0.489 Na/Mg r = 0.845.

• Journal of Energy Engineering
• /
• v.19 no.2
• /
• pp.136-142
• /
• 2010

Combustion reactivity and thermal behavior of two imported coals used as a pulverized fuel of commercially thermal power plant were investigated by thermogravimetric analysis (TGA) and large scale test furnace of 200 kg/hr. TGA results showed that combustion efficiency of high moisture coal has lower than reference coal due to the slow combustion completion rate although it has the low ignition temperature, and activation energies of high moisture coal with 79 kJ/mol for overall combustion was higher than reference coal of 53 kJ/mol. Test furnace results ascertained that flame of black band of high moisture coal during the combustion in boiler broke out compared to reference coal and then it becomes to unburned carbon due to the less reactivity and combustion rate. But, Blending combustion of high moisture coal with design coal of high sulfur are available because sulfur content of high moisture coal was too low to generate the low SOx content in flue gas from boiler during the combustion. The ash analysis results show that it was not expected to be associated with slagging and fouling in pulverized coal fired systems due to the low alkali metal content of $Na_2O$ and $K_2O$ compared to bituminous coal.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.8
• /
• pp.8-13
• /
• 2018

Nitrogen oxides (NOx) have recently been very influential in the generation of ultrafine dust, which is of great social interest in terms of improving the atmospheric environment. Nitrogen oxides are generated mainly by the reaction of nitrogen and oxygen in air in a combustion gas atmosphere of high temperature in a combustion apparatus such as thermal power generation. Recently, research has been conducted on the combustion that recirculates the exhaust gas to the cylindrical burner by using a piping using a Coanda nozzle. In this study, three types of burners were carried out through computational fluid analysis. Case 1 burner with the outlet of the combustion gas to the right, Case 2 burner with both sides as gas exit, Case 3 burner with left side gas exit. The pressure, flow, temperature, combustion reaction rate and distribution characteristics of nitrogen oxides were compared and analyzed. The combustion reaction occurred in Case 1 and Case 2 burner in the right direction with combustion gas recirculation inlet and Case 3 burner in the vicinity of mixed gas inlet. The temperature at the outlet was about $100^{\circ}C$ lower than that of the other burners as the Case 2 burner was exhausted to both sides. The NOx concentration of Case 1 burner at the exit was about 20 times larger than that of the other burners. From the present study, it could be seen that it is effective for the NOx reduction to exhaust the exhaust gas to both side gas exits or to exhaust the exhaust gas to the opposite direction of inlet of recirculation gas.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.6
• /
• pp.648-653
• /
• 2006

As an alternative for the traditional materials packed in biofilters treating gaseous VOCs, a novel packing material has been developed and tested. In the packing material(named as Hydrogel Bead, HB), pollutant-degrading microorganisms were immobilized in hydrogel consisted of alginate, polyvinyl alcohol(PVA), and powdered activated carbon. A closed-bottle study showed that the HB rapidly removed gaseous styrene without the losses of adsorption and biodegradation capacity. Biofilter column experiments using the HBs also demonstrated that greater than 95% of removal efficiencies were found at an inlet styrene loading rate of $245g/m^3/hr$, which was higher biofilter performance than other elimination capacity reported earlier. Furthermore, when the inlet styrene concentration increased stepwise, the adsorption played an important role in overall styrene removals. The absorbed styrene was found to be biodegraded in the following low inlet loading condition. Consequently, the new HB material is able to successfully minimize the drawbacks of activated carbon(necessity of regeneration) and biological processes(low removal capacity at dynamic loading conditions), and maximize the overall performance of biofilter systems treating VOCs.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.12
• /
• pp.1329-1336
• /
• 2007

This study was carried out to develop an efficient process abating high NO concentration. A hybrid process of selective catalytic reduction(SCR) and activated carbon fiber(ACF) adsorption was newly designed and tested. Used ACF in NO adsorption was regenerated by simultaneously applying heat and vacuum. The result of ACF regeneration was for superior in the desorption condition at $140^{\circ}C$ and vacuum 600 mmHg. A commercial catalyst was used at the conditions of reaction temperature at $300^{\circ}C$, $NH_3/NO$ mole ratio = 1.0 for SCR process. NO evolved from ACF regeneration reactor could be removed by SCR reactor up to 98%. But high concentration of NO was exhausted from SCR reactor for one minute when the flue gas of NO 300 ppm and deserted NO from ACF regeneration were simultaneously treated by the same SCR reactor. Therefore, it is necessary to use additional small sized SCR reactor or to increase $NH_3$ concentration for a short time along with NO concentration rather than to mix flue gas with the gas evolving from ACF regeneration at fixed $NH_3$ inlet concentration. The hybrid process of SCR and ACF showed high NO removal efficiency over 80% at any time courses. Through the repeated cycles, stable DeNOx efficiency was maintained, indicating that the hybrid process would be a good countermeasure to the spotaneously high NO concentration instead of increasing the SCR capacity.

• Journal of Conservation Science
• /
• v.36 no.2
• /
• pp.82-92
• /
• 2020

Modern artworks are constructed using a variety of materials and techniques. Sculptures, which predominantly consist of metals, usually have different shapes and consist of different material mixtures. The structural and material properties of these sculptures are often controlled by conservation treatment methods. However, the application of existing treatment methods is challenging at times, indicating that more diverse treatment materials and techniques are necessary. Therefore, in this study, a treatment method that employs volatile corrosion inhibitor(VCI) powder, rather than an anti-corrosion solution, for the conservation and management of metal artworks was used. VCI powder and VCI films containing VCI powder were used, and the results obtained confirmed that both of them showed anti-corrosion effect. Only a slight change in the chromaticity of metal samples was observed, and compared to the untreated samples, the application of the VCI powder resulted in a decrease in the rate of corrosion by half. Moreover, VCI film tests revealed that comparing to the untreated or polyethylene film-treated samples, VCI film treatment resulted in a decrease in the occurrence of corrosion compounds. The contact angle, surface energy, and surface electrical resistance were measured, and the evaluation of these surface properties established the anti-corrosion effect of VCI. Additionally, direct application of VCI and VCI films on actual sculptures further confirmed the anti-corrosion effect of VCI.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.3
• /
• pp.935-939
• /
• 2018

3D Printing technology is developing in various prototypes for medical treatment, food, fashion as well as machinery and equipment parts production. 3D printing technology is also able to fully be utilized to other industries in terms of developing its technology which has been reported in many field of areas. 3D printing technology is expected to be used in various applications related to $4^{th}$ industrial revolution such as finished products and parts even it is still carried out in the prototype model. In this study, we have investigated and developed conductive resin for 3d printing application based on reduced graphene oxide(rGO)/Polypyrrole(Ppy) composite and polycaprolactone(PCL) as a biodegradable polymer. The electrical properties and surface morphology of the conductive PCL resin based on therGO/Ppy composite were analyzed by 4point-probe and scanning electron microscope(SEM). The conductive PCL resin based on rGO/Ppy composite is expected to be applicable not only 3D printing, but also electronic materials in other industrial fields.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.3
• /
• pp.731-743
• /
• 2018

In bio-jet fuel production, selecting operating conditions of hydro-upgrading is of great importance to make iso-Paraffin rich hydrocarbons with carbon distribution including jet fuel range. Herein, iso-Paraffin rich biofuel including jet fuel range hydrocarbons ($C_8-C_{16}$) is produced from simultaneous cracking and isomerization using n-Paraffin rich hydrocarbon derived from hydrotreated vegetable oil over 0.5 wt..% Pt/Zeolite catalyst. We report and analyze the yields and compositions in the produced hydrocarbons affected by various operating conditions, such as reaction temperature, reaction pressure, molar ratio of reactants, and weight hourly space velocity. Aforementioned operating conditions not only can help interpret the reaction dynamics of hydro-upgrading, but also further produce bio jet-fuel after distillation.