• Journal of the Korean Geotechnical Society
• /
• v.18 no.6
• /
• pp.73-81
• /
• 2002

Various CPT-based prediction models far profiling stress history of marine clay at the southern part of the Korean peninsula were investigated by using both statistical analysis and case history study. Preconsolidation pressures($\sigma'$p) and overconsolidation ratio(OCR) estimated by empirical correlations and cone penetration tests were compared with those of laboratory odometer test results. Stress history of marine clay determined by odometer test results was in general overconsolidated at below 10m depth from the mudline, whereas marine clay at below l0m depth from the mudline which has an around 0.3 overconsolidation ratio showed variable stresses and unstable states. Preconsolidation pressures were computed by both empirical methods of the Chen and Mayne(1996) and theoretical method of Konrad and Law(1987). It is estimated that Chen and Mayne(1996)'s prediction method based on pore water pressure is more reliable than any other prediction methods, and their method proved to be the most reliable for overconsolidation ratio estimation. However, it is recommended that Mayne & Holtz(1988) and Mayne & Bachus(1988) methods are more suitable than any other methods for predicting the overconsolidation ratio at an underconsolidated (OCR<1) clay. For these reasons, rather than making use of existing prediction models, development of site specific empirical correlations which considers local characteristics and site conditions may be required due to different local stress history and variable soil properties.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.9
• /
• pp.37-50
• /
• 2016

Gravel compaction pile (GCP) is widely used as it increases the bearing capacity of soft ground and reduces the consolidation settlement. Stress concentration ratio for GCP design is dependent on the area replacement, surcharge pressure and depth. However, a range of stress concentration ratio obtained through field, laboratory experiments and numerical analysis is large. Little study has been done on the stress concentration ratio for the mixing ratio of gravel and sand. The main objective of the study is to evaluate the stress concentration ratio for both area replacement ratio and mixing ratio through literature review and numerical analysis. Numerical analysis using the finite element program ABAQUS 6.12-4 has been performed for the composite ground with GCP. The excess pore water pressure and stress concentration ratio of composite ground have been analyzed for both the area replacement ratio and the mixing ratio. Based on the previous research results, a range of stress concentration ratio obtained from the field tests, laboratory tests, numerical analysis on the GCP studies is found to be 1.7-3.2, 2.0-7.5 and 2.0-6.5, respectively. Based on the numerical analysis results, as the area replacement ratio increases, the stress concentration ratio increases up to 30% and then decreases at 40%. Also, the stress concentration ratio tends to increase up to 70:30 and then to decrease after 60:40.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.6
• /
• pp.49-59
• /
• 2016

We develop liquefaction resistance curves, which represent the correlation between cyclic resistance ratio (CRR) and number of cycles (N) to estimate the build-up of residual excess pore pressure from simple shear tests performed for this study and also from published literature. The liquefaction curve is calculated from two models. The comparisons show that one of the models is not reliable because it underestimates CRR. The scatter of the data is shown to be significantly reduced when CRR is normalized to the resistance ratio at N = 15 ($CRR_{N=15}$). Use of the normalization is particularly useful because CRR can be easily estimated from field tests. From normalization, we propose mean, upper, and lower curves. The corresponding design equation and its parameters are also proposed. We believe that the proposed curves can be used for effective stress site response analyses and evaluation of the seismic performance of port structures.

• Journal of Energy Engineering
• /
• v.23 no.2
• /
• pp.149-157
• /
• 2014

The steam generator tubes of nuclear power plants have various types of corrosion failures during the plant operation. The stress corrosion cracking which occurs on the outer surface of tube is called the secondary side stress corrosion cracking and mainly occurs in the expansion-transition area of tube. The causes are the concentration of impurities by the sludge pile-up related to the geometry of its region and the residual stress by tube expansion in the process of steam generator manufacturing. Especially the directionality and sizes of residual stresses are differed according to the tube expansion methods and the direction and the frequency of tube cracks depend on their characteristics. In bases on the plant experiences, it is notified that circumferential cracks of tubes expanded with explosive expansion method are dominantly occurred compared to those of tubes done with hydraulic expansion one. Therefore in this study, according to tube expansion methods frequencies and sizes of tube cracks with specific direction are compared by means of accelerated immersion test and also the crack morphology and the specific chemicals from water-chemistry environment are observed through the fracture surface examination.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.5
• /
• pp.281-290
• /
• 1999

The coastal area, particularly along the West and South coasts in Korea, is often reclaimed with dredged marine-clay to meet the demand of land capacity. A large number of ground improvement techniques are developed for such a newly formed soft clay deposit. However, the quick lime column method, which is effectively used for the purpose of ground improvement in the other countries, is seldom applied in Korea. This study, therefore, focuses on the development of appropriate soft soil improvement technique by using quick lime column. A model test as well as finite element analysis was conducted to identify the consolidation characteristics around the lime column. Although actual pore water pressure measured from model tests does not coincide with the predictions made by finite element method and Chen ＆ Law's theoretical formula, their trends are quite similar. It is revealed from this study that the pressure caused by the expansion of lime column affects considerably the consolidation characteristics of the surrounding ground.

• The Journal of Engineering Geology
• /
• v.33 no.1
• /
• pp.151-167
• /
• 2023

This study compares the revised method in loose saturated sandy ground where the LNG storage tank will be installed with an evaluation method by one-dimensional effective stress analysis using the UBC3D-PLM model. Various laboratory and field tests were conducted to establish the parameters necessary for evaluation. The revised liquefaction evaluation method using the seismic response analysis result and N value from standard penetration testing evaluated the possibility of liquefaction as high, but assessment using effective stress analysis, which can consider various liquefaction resistance factors, found the site to be somewhat stable against liquefaction. One-dimensional finite element analysis using UBC3D-PLM modeling facilitated easier assessment of stability against liquefaction than the other methods and minimized the area required for reinforcement against liquefaction. In addition, it is expected that two-and three-dimensional numerical analysis considering the foundation of the LNG storage tank can identify the seismic design and behavior when liquefaction occurs.

• Geotechnical Engineering
• /
• v.14 no.4
• /
• pp.61-76
• /
• 1998

Various kinds of reinforced soil methods have been developed by many researchers or companies for their economic merits mainly. These methods have generally used sandy soils which have high permeability as embanking or backfill material. That is because, if poor embanking materials, especially like a clayey soil which has very low permeability, are used in a reinforced soil embanking, and if excessive pore water pressure is produced by external factors, the friction resistance between reinforcing members and Boils decrease, as a result possible damage or collapse of the body of a reinforced embankment. In fact, clayey Boils can also be used as a embanking materials with reinforcement which has high permeable capacity, and are expected to be able to dissipate the excess pore water pressure effectively. In this study reinforcing effects have been examined through a serries of direct shear tests in which clayey soils are reinforced with nonwoven geotextiles of which permeability is very high and tensile strength is relatively weaker than geogrids which are usually used in reinforced soil wall. Even though such nonwoven geotextile are used as reinforcement of high saturated clayey soils. the test results show the possibility that nonwoven geoteztiles could be used as a reinforcement for reinforced soil walls effectively.

• Tunnel and Underground Space
• /
• v.32 no.6
• /
• pp.518-529
• /
• 2022

In Task C of the DECOVALEX-2023 project, nine institutes from six nations are developing their numerical codes to simulate thermo-hydro-mechanical coupled behavior for the FE experiment performed at Mont Terri underground rock laboratory, Switzerland. Currently, Step 1 for comparing the simulation results to field data is the ongoing stage, and we used the OGS-FLAC simulator for a series of numerical simulations. As a result, temperature increase depending on the heating hysteresis was well simulated, and saturation variation in the bentonite depending on phase change was observed. However, due to the suction overestimation, relative humidity and temperature change in the bentonite and the pressure variation in the Opalinus clay showed a difference compared to the field data. From the observation, it is confirmed that the effect of the bentonite capillary pressure is dominant to the flow analysis in the disposal system. We further plan to draw improved results considering tunnel support material and accurate initial water pressure distribution. Additionally, the thermal, hydrological, and mechanical anisotropy of the Opalinus clay was well simulated. From the simulation results, we confirmed the applicability of the OGS-FLAC simulator in the disposal system analysis.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.5
• /
• pp.27-39
• /
• 2012

In this paper, a series of centrifuge tests were performed to evaluate the seepage characteristic of reinforced embankment. The centrifuge models simulated an actual embankment reinforced by enlargement of levee cross-section. The centrifuge models have the same conditions except the locations of enlargement with low permeable material : water-side and land-side. In addition, the prototype embankment is constructed on low permeable clay layer. In the case of water-side reinforcement, the reinforced zone makes water head down and the saturated zone of embankment propagates slowly. In the case of land-side reinforcement embankment, the saturated zone enlarged relatively faster but the amount of exit water at land-side toe was very small because of the land-side reinforcement zone. The low permeable clay foundation layer was being continuously saturated by the inflow from the embankment as well as the uplift flow from the permeable layer induced by the excess pore water pressure.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.2
• /
• pp.55-66
• /
• 2009

At the mudstone slope located on the roadside of the Seokri area in Donghae-myeon, Pohang, Gyeongsangbuk-do, this study was performed to analyze the effects of rainfall on the stability of slope through seepage analysis according to the precipitation type of the mudstone slope, referring to the actual case of slope failure. For this, precise geological survey, geophysical exploration and drilling survey for the slope where the failure occurred were performed and followed by analysis of detailed soil layer. For the section where failure surface located, the durability reduction of rocks was measured through slaking/swelling tests and the permeability was measured through in-situ permeability tests for each soil layer. In addition, the change of strength parameter and process of instability were analyzed by back analysis, using Talren 97 and Slope/W programs, in the slope. By applying different precipitation conditions to the geographical conditions of the slope that had actual failure records, the slope stability was analyzed by seepage analysis according to duration of rainfall and rise of groundwater level resulting from the flow of rainfall caused by development of geological structures and the slope surface condition.