• Journal of the Korean Institute of Gas
• /
• v.2 no.4
• /
• pp.1-6
• /
• 1998

In order to increase design efficiency, it is required to design steam boiler pressure parts systematically considering daily start-stop operation and load variation. The objective of this research is to develope an integrated system for increasing design efficiency of boiler pressure parts. The developed system consists of three program modules: (1) flexibility design module for the header stub considering fatigue life, (2) fatigue limit calculation and life evaluation module for the thick-walled boiler pressure part under cyclic operation using TRD301 code, (3) drawing automation module for the header and drum producing design drawings, welding data and bill of materials.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.9
• /
• pp.789-795
• /
• 2014

In this study, the distribution characteristics of diffusers with various shapes that are installed in an open-type thermal storage system are numerically investigated. Four diffusers are designed to distribute a working fluid evenly through the holes on bifurcated pipes. Three-dimensional steady simulations of incompressible laminar flow are conducted using commercial software (ANSYS-FLUENT). The simulation results show that both the bidirectional header-type diffuser and the H-type diffuser distribute the working fluid evenly whereas both the unidirectional and the bidirectional diffusers distribute the working fluid unevenly. The results also show that the H-type diffuser requires a higher head of pump than the bidirectional header-type diffuser. Therefore, the bidirectional header-type diffuser is recommended for use because it enables even distribution of the working fluid and requires a low head of pump.

• Tunnel and Underground Space
• /
• v.31 no.6
• /
• pp.440-459
• /
• 2021

Roadheaders have begun to be adopted in Korean tunneling sites. The performance prediction models proposed by the manufacturer are used by Korean construction companies. The models use UCS (uniaxial compressive strength) value to predict the net cutting rate, but the rock specimens conducted for the uniaxial compression test have 1.0 of the diameter to length ratio. It has been reported that the specimen shape generally influences the rock strength. The previous references studying the shape effect were cited, and the UCS data of Korean rocks are also updated to analyze the shape effect on UCS. The cause of effect was discussed by previous theory. The change amount of UCS values of Korean rocks was estimated by the data, and the modified prediction model for NCR was finally suggested.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.25 no.6
• /
• pp.324-330
• /
• 2013

The main objective of this work is to experimentally investigate the effect of inlet geometries on the distribution of two-phase annular flow at header-channel junctions simulating the corresponding parts of compact heat exchangers. The cross-section of the header and the channels were fixed to $16mm{\times}16mm$ and $12mm{\times}1.8mm$, respectively. Experiments were performed for the mass flux and the mass quality ranges of $30{\sim}140kg/m^2s$ and 0.3~0.7, respectively. Air and water were used as the test fluids. Three different inlet geometries of the header were tested:no restriction (case A), a single 8 mm hole at the center (case B), and nine 2 mm holes around the center (case C) at the inlet, respectively. The tendencies of the two-phase flow distribution were different, in each case. For cases B and C (flow resistance exists), more uniform flow distribution results were seen, compared with case A(no flow resistance), due to the flow pattern change to mist flow from annular flow at the inlet, and the flow recirculation near the end plate of the header.

• Proceedings of the Korean Information Science Society Conference
• /
• 2005.11b
• /
• pp.355-357
• /
• 2005

본 논문은 한국전자통신연구원에서 개발된 나노큐플러스 운영체제기반의 센서네트워크에서 각 노드의 응용모듈에 대한 버전을 관리하기 위한 기법을 제안한다. 제안한 기법을 응용모듈의 버전을 관리하기 위하여 고유식별번호를 각 노드의 헤더파일에 저장한다. 관리자 또는 개발자가 헤더파일에 저장되어 있는 각 노드의 고유한 식별번호를 사용하여 별도의 저장소에 저장되어 있는 노드의 형상정보를 한눈에 알아볼 수 있는 버전관리 기법을 제시하였다. 제안한 버전관리 기법을 나노큐플러스 운영체제기반의 센서네트워크 응용모듈에 적용하면 개발자 입장에서 각각의 응용모듈 변경에 대한 버전관리가 용이해지고, 형상항목인 소스코드간의 연관관계 및 변경된 소스코드의 버전에 대한 가시성을 향상시킬 수 있을 것으로 기대한다.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.1
• /
• pp.31-38
• /
• 2008

Ad-Hoc network is a network architecture which has no backbone network and is deployed temporarily and rapidly in emergency or war without fixed mobile infrastructures. All communications between network entities are carried in ad-hoc networks over the wireless medium. Due to the radio communications being extremely vulnerable to propagation impairments, connectivity between network nodes is not guaranteed. Therefore, many new algorithms have been studied recently. This study proposes the secondary header approach to the cluster based routing protocol (CBRP). The primary header becomes abnormal status so that the primary header can not participate in the communications between network entities, the secondary header immediately replaces the primary header without selecting process of the new primary header. This improves the routing interruption problem that occurs when a header is moving out from a cluster or in the abnormal status. The performances of proposed algorithm ACBRP(Advanced Cluster Based Routing Protocol) are compared with CBRP. The cost of the primary header reelection of ACBRP is simulated. And results are presented in order to show the effectiveness of the algorithm.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.15 no.3
• /
• pp.7-13
• /
• 2019

To improve the flow distribution at channel locations in the welded plate heat exchanger with "L"-type inflow, the flow visualization of Model 1 was carried out. Besides, the characteristics of flow distribution was investigated experimentally according to the header shape. The inlet flow rate for each channel location was increased at the side channels but decreased at the central channels. In the case of Model 2, which has a slant structure added to the basic header of Model 1, the unevenness of inlet flow increased by 23% from 0.019 to 0.023 as compared to Model 1. On the other hand, Model 3, which has a baffle structure added to Model 2, showed 0.064 unevenness in inlet flow, which was a 36% reduction one compared to Model 1. To improve the distribution at each channel in the welded plate heat exchanger with "L"-type flow, it is necessary to improve the header external shape for the guide of flow as well as the baffle structure for reduction of vortex flow.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.4
• /
• pp.367-372
• /
• 2010

A power plant's heat exchangers work under poor conditions, such as high temperature, high pressure, corrosion, mechanical stress and vibration. Especially, partial joint-weld of heat exchanger's header to stub-tube is the place where incomplete penetration flaws can easily occur. But, it is hard to evaluate the safety of the structure by conventional nondestructive testing techniques. So it is necessary to test integrity of the weld inside and to develop testing technique and equipment that can detect the flaws at the weld point in order to enhance reliability of the test result. In this study, we developed a suitable automated ultrasonic testing system that can inspect the partial joint-weld of header to stub-tube of power plant. Finally, we showed the efficiency of the automated ultrasonic-testing-system from the application.

• Tunnel and Underground Space
• /
• v.33 no.5
• /
• pp.414-424
• /
• 2023

In this study, a total of 326 data on a variety of geometric parameters of pick cutters and the corresponding cuttable rock conditions were collected and built as a database. Statistical analysis of the database showed that there is a significant positive correlation between the parameters that define the geometry of a pick cutter, especially between the parameters related to the length of a pick cutter and the geometry of a tungsten carbide insert. The diameter of a pick cutter shaft was also strongly correlated with the geometry of the inserts. On the other hand, it was difficult to find a clear correlation between the parameters for the rock conditions defined by the four conditions and the geometric parameters of pick cutters, which may be due to the uncertainty of the rock mass and the fact that the application of a pick cutter is presented as a range rather than a numerical single value. However, the mean values of geometric parameters of pick cutters tend to increase as a rock mass becomes harder. However, the pick length parameters are found to decrease as a rock mass becomes harder, which may be a way to reduce the moments that can occur when using long pick cutters in a hard rock condition.

• Journal of Energy Engineering
• /
• v.8 no.4
• /
• pp.605-611
• /
• 1999

Conventional methods for assessing remaining life of critical high temperature components in fossil power plants rely on nondestructive inspection practices and accompanying life analysis based on fracture mechanics By using these conventional methods. It has been difficult to perform uninterrupted in-service inspection for life prediction. Thus, efforts have been made for developing on-line remaining life monitoring systems employing information on the shape of structures, operating variables and material properties. In thus study, a software for on-line life monitoring system which performs real-time life evaluation of a high temperature system headers was developed. The software is capable of evaluating creep and fatigue life usage from the real-time stress data calculated by using temperatures/stress transfer Green functions derived in advance for the specific headers. The major benefits of the developed software life in determining future operating schedule, inspection interval, and replacement plan by monitoring real-time life usage based on prior operating history.