• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2007.03a
• /
• pp.112-121
• /
• 2007

지보재의 파괴가 고려된 터널의 안전율을 산정하기 위해 허용응력 설계법에 기초하여 숏크리트 내에 발생하는 응력이 허용응력을 초과하면 숏크리트가 파괴된다고 가정하고, 전단강도 감소기법을 이용하여 수치해석적(2차원)으로 구하는 방법이 유광호 등(2005)에 의해 제시되었다. 하지만 허용응력 설계법에 근거한 방법은 숏크리트의 허용 휨응력을 과소평가하여 터널의 안정성 및 안전율을 과소평가하는 경향이 있다. 따라서 본 논문에서는 숏크리트의 파괴거동을 갱도모형실험을 통해 확인하고 3차원 수치해석에 의해 검증하였다. 갱도모형실험에 사용된 터널은 실제 터널의 거동을 모사하기 위해 폭 3.3m, 높이 2.9m, 깊이 0.5m의 마제형으로 제작되었다. 지보재인 숏크리트는 거푸집을 이용하여 타설하고 28일간 양생하였고 7개의 실린더와 30cm의 모래 뒷채움을 이용하여 지보재에 최대한 등방하중이 가해질 수 있도록 하여 실험을 수행하였다.

• Fire Science and Engineering
• /
• v.27 no.5
• /
• pp.26-31
• /
• 2013

In nuclear power plant, anchor bolts for pressurizer supports are sufficiently used in terms of safety reason, but field inspections have reported that some bolts exceed the limit of their allowable hardness. Because the high level of hardness may lead to failures due to the stress corrosion or fracture toughness, a regular inspection is required for the bolts in nuclear power plant. Thus, this research measures the hardness of bolts currently used in pressurizer supports and then estimates maximum allowable stresses preventing failures by stress corrosion and fracture toughness. Using the ANSYS program, the stresses of the bolts in the regular condition and accidental condition have been calculated, and the possible maximum stress has been compared with the estimated allowable stresses. From the results, the stresses of bolts in the accidental condition satisfy the allowable safety stress from the stress corrosion failure. However, in the future, it shall be needed to consider the reflection of the structure assembling method on the assembling procedure to ensure the pressurizer integrity during maintenance period time.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.1
• /
• pp.25-32
• /
• 2015

This study analyzed a monitoring data, based on the initial limit values of monitoring in subway, of concrete lining stress and reinforcement stress. The data is obtained from 7 sections of the Seoul metropolitan subway line No 6, 7, and 9 in about 5 years. Also, a research is performed to set up the limit values of management monitoring, which will be applied to management monitoring in tunnel, through comparing the limit values of overseas management monitoring data and that of domestic management monitoring data. And the result obtained from comparison shows that the safety phase is 60% of allowable stress, the attention phase is 80% of allowable stress and the precision analysis phase is 100% of allowable stress. Also, we presented a method of management monitoring by the absolute value which can be easily applied in practical affairs.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.1
• /
• pp.25-35
• /
• 2015

The goal of this study was to review the visual grading and allowable stress determination methodologies for the domestic softwood. Previous studies used different grading (KFRI 1995-27, KFRI 2000-39, KFRI 2007-3, KFRI 2009-1) and allowable stress determination methodologies (ASTM D 245, KS F 2152, JAS 1990). The results of the visual grading were different by each researcher. Compared to the $1^{st}$ grade proportion from the previous studies using the previous specification on visual grading (KFRI 1995-2007), a higher $1^{st}$ grade proportion was found from the studies using the current specification (KFRI 2009). Compared to the allowable stress values from the small clear sample, the higher allowable stress values from the structural size were found. The results indicated that the strength reduction factor used in small clear sample was too conservative for the different grades. To obtain consistent results for the grade, it is required to have experts in visual grading and authorized organizations. An official standard methodology for the allowable stress value determination needs to be defined for the reliable stress value.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.1
• /
• pp.158-166
• /
• 2008

Member force, strain and stress distribution of a section are obtained for prestressed steel and concrete(PSSC) composite bridge subjected to dead and live load in order to interpret the effect of prestressing and deformation of tendon. The stress and strain distribution and moment capacity are obtained for both noncomposite and composite section and for allowable stress limit state, yield limit state and strength limit state. Reliability analysis is conducted after assuming limit states for deflection, stress and flexural strength. Comparing that the reliability index for stress is near 0 for example section which is designed to satisfy the allowable stress exactly, the reliability indexes for deflection and flexural strength are high. Reliability of PSSC girder which is designed based on allowable stress of bridge design code is high for deflection and flexural strength.

• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.1334-1340
• /
• 2004

Existing of angle assembly and angle beam joint examination with steel pole and steel beam of assembly existing anglerather then excellent enumerate, joint of beanding moment examination and economical existing show, in the futher, angle beam rather then steel I beam with all change.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.9
• /
• pp.780-785
• /
• 2016

Heavy oil used as ship propulsion has a serious issue regarding exhaust emission of global warming. Recently, among large-scale merchant ships are using LNG as green ships so called ech-ships. In this study, an vaporizer and pipes under cryogenic and high pressure load were considered to evaluate structural integrity according to codes. Structural analysis of the vaporizer and pipes was performed using the commercial code, ANSYS. Integrity evaluation of the vaporizer based on von Mises stress was performed in accordance with allowable stress specified in ASME Boiler & Pressure Vesssel Section VIII Division 2. To assess structural integrity of the pipes, stress components were combined and compared with ASME B31.3. The calculated stresses for all load cases are lower than allowable stresses, therefore the structural integrity of equipments are verified.

• Journal of the Society of Disaster Information
• /
• v.17 no.3
• /
• pp.454-464
• /
• 2021

Purpose: There is a need to construct an evacuation passageway for the 2-Arch tunnel, which has been constructed and is in operation. Therefore, it aims to analyze tunnel and center wall behaviour and stability due to excavation of the center wall. Method: We describe the theoretical background of 2-Arch tunnel and evacuation passageway, and focused on analyzing the behaviour of tunnel and wall using 3-dimensional finite element analysis. Parametric analysis according to rock rating was performed with various ground conditions, and the displacement and stress of the center wall were intensively analyzed. Result: With the center wall excavation, the largest amount of settlement was shown in the center of the opening, and the stress was greatest during the first excavation. In addition, it was shown that stress concentration occurred at the top of both openings, and stability reviews considering the concept of allowable stress showed that it exceeded the allowable stress. Conclusion: Although the displacement of the tunnel has secured stability within the allowable standard, the generated stress is found to exceed the allowable standard, so it is necessary to prevent sudden stress release by applying appropriate reinforcement methods during construction.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05a
• /
• pp.995-1000
• /
• 1995

ASME B&PV Code Section III NB-3200의 규정은 원자로 관련 1등급 부품의 설계시 지켜야할 사항이다. 이 규정은 운전조건별로 허용응력에 대한 분류를 하여 허용한도를 규정하고 있다. 따라서 응력해석시 이 규정을 적용하기 위해 해석결과의 검색, 추출정리, 추가계산 등 응력해석 후속작업을 위한 통합 program을 awk 언어를 사용하여 개발하였다. 이 통합 Program은 ASME에 규정된 응력별로 여러 개의 awk program module로 작성하였고 각각의 모듈을 통합하는 UNIX script file로 구성되어있다. 각각의 모듈은 독립된 batch 작업이 가능하고, 이것을 모두 연계한 batch 작업 역시 가능하도록 하였다. 문서작성시 도표작성을 용이하게 하기 위해 후처리결과가 하나의 디렉토리에 저장되도록 하였다.

• Fire Science and Engineering
• /
• v.31 no.4
• /
• pp.65-70
• /
• 2017

The seismic performance of press fittings is studied, which is one of the weldless joints of stainless steel pipe used in the water piping of recent fire protection system. The piping of this study was constructed based on the piping connection reference of NFPA 13. The permissible displacement of the piping was set as the allowed amount which is given in the Building Structure Standard, and the measurements were repeated 10 times. The Von-mises stress of the piping was 2.48 and 1.25 times of the allowed amount of stress, which was less than the standard, noted three times on the NPPs Allowable Stress for Level D service loading. Therefore, the press fittings shows enough seismic performance.