• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.3 no.1 s.4
• /
• pp.53-65
• /
• 2004

A series of accidents, which are non-recurrent and non-anticipated, are called incidents. These incidents make standard traffic flows interrupt, which result in the decrease of road capacity and a number of social and economic costs, such as the traffic congestion and air pollution. In order to prevent the hazard of incidents, domestic and foreign traffic management center are likely to opt auto-sense system with algorithms of auto-incident sense. However, it is evaluated that the algorithms have a low function with frequent wrong alarms, even if they accurately ry to speculate the incidents. In the case of bottleneck which has lack of road capacity, compared with other roads, due to inefficient road structured over-capacity of the demand of on-off ramp, the incidents regularly take place. Nonetheless, it can be more difficult to speculate the auto-incidents sense owing to similar incidents, such as the queue of in-out flows of cars and the change of road line. Throughout this research, the function of the model has improved excluding near road line in the module of the incidents which is based on the auto-incidents algorithms during the sense of the congestion of ramp areas.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.15 no.5
• /
• pp.11-24
• /
• 2011

A real-time hybrid test of a 3 story-3 bay reinforced concrete frame which is divided into numerical and physical substructure models under uniaxial earthquake excitation was run using a fixed iteration implicit HHT time integration method. The first story inner non-ductile column was selected as the physical substructure model, and uniaxial earthquake excitation was applied to the numerical model until the specimen failed due to severe damage. A finite-element analysis program, Mercury, was newly developed and optimized for a real-time hybrid test. The drift ratio based on the top horizontal displacement of the physical substructure model was compared with the result of a numerical simulation by OpenSees and the result of a shaking table test. The experiment in this paper is one of the most complex real-time hybrid tests, and the description of the hardware, algorithm and models is presented in detail. If there is an improvement in the numerical model, the evaluation of the tangent stiffness matrix of the physical substructure model in the finite element analysis program and better software to reduce the computational time of the element state determination for the force-based beam-column element, then the comparison with the results of the real-time hybrid test and the shaking table test deserves to make a recommendation. In addition, for the goal of a "Numerical simulation of the complex structures under dynamic loading", the real time hybrid test has enough merit as an alternative to dynamic experiments of large and complex structures.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.04a
• /
• pp.153-158
• /
• 1995

보 및 평판의 진동에 대해서 에너지의 손실은 재료감쇠를 이용한 표면감쇠처리나 지지부에서의 감쇠처리에 의하여 증가될 수 있다. 감쇠재료를 이용한 표면감쇠처리의 예로서 보/평판 표면에 접착되는 감쇠 테이프나 코팅등은 아주 효과적임이 입증되었다. 마찬가지로 지지부 감쇠처리는 점탄성재료의 삽입에 의해서 설명될수 있다[1]. 보/평판의 감쇠에 대한 최근의 많은 연구들은 진동하고 있는 보/평판의 표면에 적용하는 감쇠 테이프 혹은 적층형태의 감쇠 처리방법에 대해서 주로 수행되었다. 일반적으로 표면감쇠처리방법은 진동감소에 아주 효과적이지만 실제 적용상에서 항상 가능한 것은 아니며, 이와 같은 경웨는 지지부 감쇠 처리방법에 의존하게 된다[2]. 감쇠특성을 갖는 점탄성재료를 실제로 적용할 때 보/평판의 유한한 길이가 점탄성재료로 지지되며 점탄성재료의 물성치와 치수에 따라서 계의 모우드 매개변수(고유진동수, 계의 손실계수 그리고 모우드형상)가 크게 달라진다. 그리고 이와 같은 계에 대해서는 지지부의 거동보다는 전체 시스템의 고유진동수와 손실계수 그리고 보 영역에서의 모우드 형상에 더 관심이 있으므로 지지부 영역을 집중매개변수(lumped parameter)로 나타내어 계를 해석할 수 있다. 일반적으로 보와 평판의 경계에서는 병진 및 회전방향의 강성 뿐만 아니라 두 강성사이에 연성효과도 동시에 발생하게 되므로 이 항을 고려하여 계를 모델링해야 한다. 본 연구에서는 우선 점탄성 재료에 의한 지지부영역의 등가 강성계수들을 구하고 경계에 강성행렬을 갖는 보의 등가시스템을 얻는다. 그리고 등가시스템의 주파수방정식으로부터 모우드 매개변수에 대한 지지부의 영향을 살펴본다. 또한 시스템이 비교적 복잡한 사각 평판의 진동에 대해서도 동강성행렬법(dynamic stiffness matrix method)을 이용하여 해석하고자 한다. 수준임이 입증되었다. 본 연구의 결과를 토대로우리나라 젊고 건강한 남성에게 적합한 무게상수는 작업자군에 대하여 25.05kg, 학생군에 대하여 20.24kg 으로 나타나 이는 미국 NIOSH 안전기준과 대체로 일치함을 발견하였다.ive structures utilized in Client/server architecture for distribution and cooperative processing of application between server and client this study presents two different data management methods under the Client/server environment; one is "Remote Data Management Method" which uses file server or database server and. the other is "Distributed Data Management Method" using distributed database management system. The result of this study leads to the conclusion that in the client/server environment although distributed application is assumed, the data could become centralized (in the case of file server or database server) or decentralized (in the case of distributed database system) and the data management method through a distributed database system where complete responsi

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.10
• /
• pp.773-782
• /
• 2020

The development of joint FE models for deep learning neural network (DLNN)-based hybrid FEA is presented. Material models of bolts and bearings in the front axle of tractor, showing complex behavior induced by various tightening conditions, were replaced with DLNN models. Bolts are modeled as one-dimensional Timoshenko beam elements with six degrees of freedom, and bearings as three-dimensional solid elements. Stress-strain data were extracted from all elements after finite element analysis subjected to various load conditions, and DLNN for bolts and bearing were trained with Tensorflow. The DLNN-based joint models were implemented in the ABAQUS user subroutines where stresses from the next increment are updated and the algorithmic tangent stiffness matrix is calculated. Generalization of the trained DLNN in the FE model was verified by subjecting it to a new loading condition. Finally, the DLNN-based FEA for the front axle of the tractor was conducted and the feasibility was verified by comparing with results of a static structural experiment of the actual tractor.

• Convergence Security Journal
• /
• v.17 no.1
• /
• pp.15-30
• /
• 2017

Since the 1990s, fingerprint recognition has attracted much attention among scholars. There have been numerous studies on fingerprint recognition. However, most of the academic papers have focused mainly on how to make a technical advance of fingerprint recognition. there has been no significant output in the analysis of the research trends in fingerprint recognition. It's essential part to describe the overall structure of fingerprint recognition to make further studies much more efficient and effective. To this end, the primary purpose of this article is to deliver an overview of the research trends on fingerprint recognition based on network analysis. This study analyzed abstracts of the 122 academic journals ranging from 1990 to 2015. For gathering those data, the author took advantage of an academic searchable data base-RISS. After collecting abstracts, cleaning process was carried out and key words were selected by using Krwords and R; co-occurrence symmetric matrix made up of key words was created by Ktitle; and Netminer was employed to analyze closeness centrality. The result achieved from this work included followings: research trends in fingerprint recognition from 1990 to 2000, 2001 to 2005, 2006 to 2010, and 2011 to 2015.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.16 no.2
• /
• pp.261-270
• /
• 2018

In this study, to replace the 'J-slot joint', a joint device between a disposal canister and an emplacement jig in Deep Borehole Disposal process, a novel joint device was designed and tested. The novel joint device was composed of a wedge on top of a disposal canister and a hook box at the end of a winch system. The designed joint device had merits in that it can recombine an emplaced canister freely without the replacement of the joint component. Moreover, it can be applied to various emplacement jigs such as drill pipes, wire-lines, and coiled tubing. To demonstrate the designed joint device, the joint device (${\Phi}110mm$, H 148 mm), a twin canister string (${\Phi}140mm$, H 1,105 mm), and a water tube (${\Phi}150mm$, H 1,500 mm) as a borehole model were manufactured at 1/3 scale. As deployment muds, Na-type bentonite (MX-80) and Ca-type (GJ II) bentonite muds were prepared at solid contents of 7wt% and 28wt%, respectively. The manufactured joint device showed good performance in pure water and viscous muds, with an operation speed of $10m{\cdot}min^{-1}$. It was concluded that the newly developed joint device can be used for the emplacement and retrieval of a deep disposal canister, below 3~5 km, in the future.

• Korean Journal of Optics and Photonics
• /
• v.9 no.2
• /
• pp.111-116
• /
• 1998

Thirteen InGaAs/InGaAsP separate-confinement heterostructure multiple quantum well lasers were designed such that the strain in the active layer from 0.9% compressive strain to 1.4% tensile, and their threshold current density was caluculated to see the effects of strain on the threshold current density. The well width was adjusted such that the bandgap of the quantum well is 1.55 ${\mu}{\textrm}{m}$, For the calculation of the band structure and transition matrix element needed for the gain calculation, a block diagonalized 8$\times$8 second-order $\to{k}.\to{p}$ Hamiltonian was used to incorporate the conduction band nonparabolicity and the valence band mixing. The threshold current density shows discontinuity at 0.4% tensile strain where the first heavy-hole subband and the first light-hole subband cross and at 0.5% tensile strain where the second conduction subband begins to exist. The threshold current density at room temperature has a maximum around these 0.4-0.5% tensile strains, and as strain varies in either direction it decreases first and then increases a little after a local minimum. This calculated trend is consistent with the other reported experimental results. We discussed the results of this calculation in comparison with other theoretical or experimental papers on the effect of strain.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.8 no.3
• /
• pp.285-294
• /
• 2003

To select an appropriate sampler for the environmental monitoring survey in coastal waters of Saemangeum, Jeollabuk-do, a macrobenthic sampling was conducted in April 2002. Employed samplers were dredge (type Charcot), a semi-quantitative sampler and Smith-McIntyre (SM) and van Veen grab (VV) as quantitative ones. One haul was tried for dredge and 3 replicates (0.1 ㎡${\times}$3) for SM and W at each of 11 stations. Comparisons of sediment volume in sampler bucket and of precision of biological parameters (i.e., density, biomass, species number and diversity index, H') were made between SM and VV. Sediment volume was significantly different (SM > VV) at p-value of 0.0050 (paired t-test) and, in average, 3 replicate samples of SM and VV satisfied a precision level of 0.2 by applying 4th root transformation. Patterns of observed and expected species numbers and H' were compared. Dredge-VV samples showed higher affinity than any other pair. Several dominant species in the area were underestimated in dredge samples (e.g., polychaete Heteromastus filiformis. Aricidea assimilis etc.). Quantifying the agreement pattern of multi-species responses was accomplished by estimating correlations between similarity matrices. Correlation between dredge and VV was slightly higher, but near-per-fect matches were found in general. Different ranks and composition among principal species lists were presumably linked to the effect of penetration depth that differs among samplers. Lower level of some species' abundance in VV samples (ca. 50％ compared with those of SM) was explained in this context. It seem appropriate to regard the effect as a probable cause of relatively higher correlations in dredge-VV, Overall bio-logica1 features indicated that a better choice could be SM in situations of requiring high data quality. The others work well, however, on observing and defining faunal characteristics and their capability cannot be questionted if we do not expect a first-order quality.

• Journal of Animal Science and Technology
• /
• v.46 no.5
• /
• pp.719-728
• /
• 2004

The aims of this study were to estimate genetic parameters for carcass traits on Hanwoo(Korean Native Cattle) and to compare two different statistical algorithms for estimating genetic parameters. Data obtained from 1526 steers at Hanwoo Improvement Center and Hanwoo Improvement Complex Area from 1996 to 2001 were used for the analyses. The carcass traits considered in these studies were carcass weight, dressing percent, eye muscle area, backfat thickness, and marbling score. Estimated genetic parameters using EM-REML algorithm were compared to those by Bayesian inference via Gibbs Sampling to find out statistical properties. The estimated heritabilities of carcass traits by REML method were 0.28, 0.25, 0.35, 0.39 and 0.51, respectively and those by Gibbs Sampling method were 0.29, 0.25, 0.40, 0.42 and 0.54, respectively. This estimates were not significantly different, even though the estimated heritabilities by Gibbs Sampling method were higher than ones by REML method. Since the estimated statistics by REML method and Gibbs Sampling method were not significantly different in this study, it is inferred that both mothods could be efficiently applied for the analysis of carcass traits of cattle. However, further studies are demanded to define an optimal statistical method for handling large scale performance data.

• Radiation Oncology Journal
• /
• v.20 no.3
• /
• pp.283-293
• /
• 2002

Purpose : A PC based brachytherapy planning system was developed to display dose distributions on simulation images by 2D isodose curve including the dose profiles, dose-volume histogram and 30 dose distributions. Materials and Methods : Brachytherapy dose planning software was developed especially for the Ir-192 source, which had been developed by KAERI as a substitute for the Co-60 source. The dose computation was achieved by searching for a pre-computed dose matrix which was tabulated as a function of radial and axial distance from a source. In the computation process, the effects of the tissue scattering correction factor and anisotropic dose distributions were included. The computed dose distributions were displayed in 2D film image including the profile dose, 3D isodose curves with wire frame forms and dosevolume histogram. Results : The brachytherapy dose plan was initiated by obtaining source positions on the principal plane of the source axis. The dose distributions in tissue were computed on a $200\times200\;(mm^2)$ plane on which the source axis was located at the center of the plane. The point doses along the longitudinal axis of the source were $4.5\~9.0\%$ smaller than those on the radial axis of the plane, due to the anisotropy created by the cylindrical shape of the source. When compared to manual calculation, the point doses showed $1\~5\%$ discrepancies from the benchmarking plan. The 2D dose distributions of different planes were matched to the same administered isodose level in order to analyze the shape of the optimized dose level. The accumulated dose-volume histogram, displayed as a function of the percentage volume of administered minimum dose level, was used to guide the volume analysis. Conclusion : This study evaluated the developed computerized dose planning system of brachytherapy. The dose distribution was displayed on the coronal, sagittal and axial planes with the dose histogram. The accumulated DVH and 3D dose distributions provided by the developed system may be useful tools for dose analysis in comparison with orthogonal dose planning.