• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.1
• /
• pp.141-152
• /
• 2022

As interest increases related to the development of eco-friendly energy, the offshore wind turbine market is growing at an increasing rate every year. In line with this, the demand for an installation vessel with large scaled capacity is also increasing rapidly. The wind turbine installation vessel (WTIV) is a fixed penetration of the spudcan in the sea-bed to install the wind turbine. At this time, a review of the spudcan is an important issue regarding structural safety in the entire structure system. In the study, we analyzed the current procedure suggested by classification of societies and new procedures reflect the new loading scenarios based on reasonable operating conditions; which is also verified through FE-analysis. The current procedure shows that the maximum stress is less than the allowable criteria because it does not consider the effect of the sea-bed slope, the leg bending moment, and the spudcan shape. However, results of some load conditions as defined by the new procedure confirm that it is necessary to reinforce the structure to required levels under actual pre-load conditions. Therefore, the new procedure considers additional actual operating conditions and the possible problems were verified through detailed FE-analysis.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.5
• /
• pp.497-504
• /
• 2023

In this study, Selective catalytic reduction (SCR) + Diesel particulate filter (DPF) system was installed on a ship with a low-speed engine to conduct the on-board test. The target ship (2,881 gross tons, rated power 1,470 kW@240 rpm ×1) is a general cargo ship sailing in the coastal area. Drawing development, approvals and temporary survey of the ship were performed for the installation of the after-treatment system. For performance evaluation, the gaseous emission analyzer was used according to the NOx technical code and ISO-8178 method of measurement. The particulate matter analyzer used a smoke meter to measure black carbon, as discussed by the International Maritime Organization (IMO). Tests were conducted using MGO (0.043%) and LSFO (0.42%) fuels according to the sulfur content. The test conditions were selected by considering the engine rpm (130, 160 and 180). Gaseous emission and particulate matter (smoke) were measured according to the test conditions to confirm the reduction efficiency of the after treatment system. The results of NOx emission and particulate matter (smoke) revealed that reduction efficiency was more than 90%. The exhaust pressure met the allowable back pressure (less than 50 mbar). This study confirms the importance of the on-board test and the potential of SCR + DPF systems as a response technology for reducing nitrogen oxides and particulate matter.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.27 no.3
• /
• pp.175-181
• /
• 2015

In this study, two dimensional wave overtopping tests for vertical wall were performed and overtopping formulas were suggested for impulsive and non-impulsive wave conditions. The test results from this study were compared with those from EurOtop(2007). The wave overtopping formulas were derived and suggested considering the recent research trends, while the existing method used the diagram. The wave overtopping formulas have the form of exponential and power functions using non-dimensional variables for wave overtopping and freeboard heights for non-impulsive and impulsive condition, respectively. The wave overtopping formula and effective parameters for inclined superstructure were also suggested. It is analyzed that the locations of inclined superstructure do not have the significant effects on wave overtopping, that is, the wave overtopping rate were almost same for each locations.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.4
• /
• pp.67-78
• /
• 2008

In this study, artificial cemented sand made of a few portland cement and Nak-Dong river sand was researched closely to investigate cementing effect quantitatively through unconfined tests and triaxial tests. The peak strength and elastic modulus increased and dilation of cemented sand was restricted by the cementation, but after breakage of the cementation, dilation and negative excess pore water pressure increased. In stress-strain curve, strain-softening behavior appeared in drained condition but strain-hardening behavior was appeared in undrained condition as a result of the increase of effective stress. The test was quantitatively analyzed by multiple regression models, correlating each response variable with input variable. The equations are valid only over the range investigated. Its adjusted coefficient of determination was $0.81{\sim}0.91$, and dry density is important factor for estimating strength of cemented sand.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.30 no.5
• /
• pp.217-222
• /
• 2018

An analytical method for determining the degree of wave refraction is investigated. The ray tracing method previously used to calculate wave propagating cannot explain the degree of refraction caused by different kinds of conditions. In this study, we suggest the index of refraction degree using the principle that refraction is caused by the difference of phase velocities along the crest line.

• Journal of Ocean Engineering and Technology
• /
• v.25 no.1
• /
• pp.44-48
• /
• 2011

Researchers suggested painted coating characteristics of aluminum sheet by various sending condition. Painted coating is used to protect the surface of the blocks from the interior and exterior. It is also used to enhance the value of automobiles and ship materials. This process makes the materials surface for protection and elegance. Although analysis of the roughness and critical scratch load of painted coating is important, the effects of this material have not progressed much. In this study, the characteristics of painted coating in the other conditions of the polished aluminum sheet were investigated. The results of both various conditions and initial roughness values were almost similar to final values after painted coating.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.1
• /
• pp.16-20
• /
• 2003

본 연구에서는 입사파에 의한 항내 정온도 계산 시 사용되는 수치해석 기법에 대한 검증 및 실제 항만에 대한 적용을 하였다. 해석기법은 유한요소기법 (finite element technique) 을 사용하였고 기본방정식은 경계조건과 마찰을 고려한 완경사방정식 (mild-slope equation) 을 사용하였다. 해석의 검증을 위하여 임의형상 항만에 대해 본 해석법을 적용하여 수치해석을 실시한 결과와 다른 수치해석결과 및 실험결과를 비교했을 때 좋은 일치를 나타내었다. 제주항에 대해서 2가지의 각기 다른 입사파 조건을 적용하여 계산한 결과 제주항이 방파제 설계파인 NNW방향 (Case 2)인 경우가 NE 방향 (Case 1)인 경우보다 약간 양호한 정온을 확보하는 것을 알 수 있었다.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.1
• /
• pp.33-40
• /
• 2003

기존 대부분의 진동제어법이 모드제어에 근거한 것인데 반면, 본 연구에서는 진동억제의 또다른 방법인 파동제어기법을 다루었다. 무반사조건을 만족하면서 진동에너지를 흡수하는 파동제어는 특히 1차원 구조계에 유용하게 사용될수 있으리라고 기대되는데, 현실적으론 제어알고리즘의 실현화에 그 어려움이 있다. 본 연구에서는 근사화된 무한구조계를 계산기내에 구축하여, 진동에너지가 근사 무한구조계에 흡수되는 조건을 제어기가 실현하는 제어수법을 개발하였다. 시뮬레이션과 실험을 통하여, 본 연구에서 제안한 파동제어기법에 의해 이동하는 현수체의 진동억제가 효율적으로 이루어짐을 확인할 수가 있었다.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.1
• /
• pp.26-32
• /
• 2003

기존 대부분의 진동제어법이 모드제어에 근거한 것인데 반면, 본 연구에서는 진동억제의 또다른 방법인 파동제어기법을 다루었다. 무반사조건을 만족하면서 진동에너지를 흡수하는 파동제어는 특히 1차원 구조계에 유용하게 사용될 수 있으리라고 기대되는데, 현실적으론 제어알고리즘의 실현화에 그 어려움이 있다. 본 연구에서는 근사화된 무한구조계를 계산기내에 구축하여, 진동에너지가 근사 무한구조계에 흡수되는 조건을 제어기가 실현하는 제어수법을 개발하였다. 시뮬레이션과 실험을 통하여, 본 연구에서 제안한 파동제어기법에 의해 회전체의 비틀림 진동억제가 효율적으로 이루어짐을 확인할 수가 있었다.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.16 no.2
• /
• pp.103-107
• /
• 2004

Empirical equation has been developed by employing the new non-dimensional physical number 'wave action slope' for the estimation of breakwater armor weight. Van der Meer(1987) introduced Iribarren number for the same purpose, but his equation shows very different trend of distribution with the condition of Iribarren number. On the other hand the equation related with wave action slope keeps the same trend of distribution over the whole region. When the parameter is related to the Iribarren number, the equation of wave action slope has a very high accuracy.