• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.28 no.2
• /
• pp.183-193
• /
• 1995

Assuming that fishing nets are porous structures to suck water into their mouth and then filtrate water out of them, the flow resistance N of nets with wall area S under the velicity v was taken by $R=kSv^2$, and the coefficient k was derived as $$k=c\;Re^{-m}(\frac{S_n}{S_m})n(\frac{S_n}{S})$$ where $R_e$ is the Reynolds' number, $S_m$ the area of net mouth, $S_n$ the total area of net projected to the plane perpendicular to the water flow. Then, the propriety of the above equation and the values of c, m and n were investigated by the experimental results on plane nettings carried out hitherto. The value of c and m were fixed respectively by $240(kg\cdot sec^2/m^4)$ and 0.1 when the representative size on $R_e$ was taken by the ratio k of the volume of bars to the area of meshes, i. e., $$\lambda={\frac{\pi\;d^2}{21\;sin\;2\varphi}$$ where d is the diameter of bars, 21 the mesh size, and 2n the angle between two adjacent bars. The value of n was larger than 1.0 as 1.2 because the wakes occurring at the knots and bars increased the resistance by obstructing the filtration of water through the meshes. In case in which the influence of $R_e$ was negligible, the value of $cR_e\;^{-m}$ became a constant distinguished by the regions of the attack angle $ \theta$ of nettings to the water flow, i. e., 100$(kg\cdot sec^2/m^4)\;in\;45^{\circ}<\theta \leq90^{\circ}\;and\;100(S_m/S)^{0.6}\;(kg\cdot sec^2/m^4)\;in\;0^{\circ}<\theta \leq45^{\circ}$. Thus, the coefficient $k(kg\cdot sec^2/m^4)$ of plane nettings could be obtained by utilizing the above values with $S_m\;and\;S_n$ given respectively by $$S_m=S\;sin\theta$$ and $$S_n=\frac{d}{I}\;\cdot\;\frac{\sqrt{1-cos^2\varphi cos^2\theta}} {sin\varphi\;cos\varphi} \cdot S$$ But, on the occasion of $\theta=0^{\circ}$ k was decided by the roughness of netting surface and so expressed as $$k=9(\frac{d}{I\;cos\varphi})^{0.8}$$ In these results, however, the values of c and m were regarded to be not sufficiently exact because they were obtained from insufficient data and the actual nets had no use for k at $\theta=0^{\circ}$. Therefore, the exact expression of $k(kg\cdotsec^2/m^4)$, for actual nets could De made in the case of no influence of $R_e$ as follows; $$k=100(\frac{S_n}{S_m})^{1.2}\;(\frac{S_m}{S})\;.\;for\;45^{\circ}<\theta \leq90^{\circ}$$, $$k=100(\frac{S_n}{S_m})^{1.2}\;(\frac{S_m}{S})^{1.6}\;.\;for\;0^{\circ}<\theta \leq45^{\circ}$$

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.15 no.4
• /
• pp.193-216
• /
• 2020

Due to the recent mid- to long-term slump and falling growth rates in the global economy, interest in organizational structures that create new products or services as a new alternative to survive and develop in an opaque environment both internally and externally, and enhance organizational sustainability through changes in production methods and business innovation is increasing day by day. In this atmosphere, we agree that the growth of small and medium-sized venture companies has a significant impact on the national economy, and various efforts are being made to enhance the technological innovation capabilities of the members so that these small and medium-sized venture companies can enhance and sustain their performance. The purpose of this study is also to investigate how the technological innovation capabilities of small and medium-sized venture companies correlate with the performance of knowledge management and to analyze the role of network capabilities to organize the strategic activities of enterprise to obtain the resources and organizational capabilities to be used for value creation from external networks. In other words, research was conducted on the impact of technological innovation capabilities of small and medium venture companies on knowledge management performance by using network capabilities as parameters. Therefore, in this study, we would like to verify the hypothesis that innovation capabilities will have a positive impact on knowledge management performance by using network capabilities of small and medium venture companies. Economic activities based on technological innovation capabilities should respond quickly to new changes in an environment where uncertainty has increased, and lead to macro-economic growth and development as well as overcoming long-term economic downturns so that they can become the nation's new growth engine as well as sustainable growth and survival of the organization. In addition, this study was conducted by setting the most important knowledge management performance within the organization as a dependent variable. As a result, R&D and learning capabilities among technological innovation capabilities have no impact on financial performance. In contrast, it was shown that corporate innovation activities have a positive impact on both financial and non-financial performance. The fact that non-financial factors such as quality and productivity improvement are identified in the management of small and medium-sized venture companies utilizing their technological innovation capabilities is contrary to a number of studies by those corporate innovation activities affect financial performance during prior research. The reason for this result is that research companies have been out of start-up companies for more than seven years, but sales are less than 10 billion won, and unlike start-up companies, R&D and learning capabilities have more positive effects on intangible non-financial performance than financial performance. Corporate innovation activities have been shown to have a positive (+) impact on both financial and non-financial performance, while R&D and learning capabilities have a positive (+) impact on financial performance by parameters of network capability. Corporate innovation activities have been shown to have no impact on both financial and non-financial performance, and R&D and learning capabilities have no impact on non-financial performance. It could be seen that the parameter effects of network competency are limited to when R&D and learning competencies are derived from quantitative financial performance. It could be seen that the parameter effects of network competency are limited to when R&D and learning competencies are derived from quantitative financial performance.

• Journal of Distribution Science
• /
• v.9 no.4
• /
• pp.5-13
• /
• 2011

This study provides analysis of the effectiveness of domestic marketing strategies of the Korean coffee shop "Caffe Bene". It bases its evaluation on statistical outputs of 'choice attributes,' "market segmentation," demographic characteristics," and "satisfaction differences." The results are summarized in four points. First, five choice attributes were extracted from factor analysis: price, atmosphere, comfort, taste, and location; these are related to coffee shop selection behavior. Based on these five factors, cluster analysis was conducted, with statistical results classifying customers into three major groups: atmosphere oriented; comfort oriented; and taste oriented. Second, discriminant analysis tested cluster analysis and showed two discriminant functions: location and atmosphere. Third, cross-tabulation analysis based on demographic characteristics showed distinctive demographic characteristics within the three groups. Atmosphere oriented group, early-20s, as women of all ages was found to be 'walking down the street 'and 'through acquaintances' in many cases, as the cognitive path, and mostly found the store through 'outdoor advertising', and 'introduction'. Comfort oriented group was mainly women who are students in their early twenties or professionals, and appeared as a group to be very loyal because of high recommendation to other customers compared to other groups. Taste oriented group, unlike the other group, was mainly late-20s' college graduates, and was confirmed, as low loyalty, with lower recommendation activity. Fourth, to analyze satisfaction differences, one-way ANOVA was conducted. It shows that groups which show high satisfaction in the five main factors also show high menu satisfaction and high overall satisfaction. This results show that segmented marketing strategies are necessary because customers are considering price, atmosphere, comfort, taste, location when they choose coffee shop and demographics show different attributes based on segmented groups. For example, atmosphere oriented group is satisfied with shop interior and comfort while dissatisfied with price because most of the customers in this group are early 20s and do not have great financial capability. Thus, price discounting marketing strategies based on individual situations through CRM system is critical. Comfort oriented group shows high satisfaction level about location and shop comfort. Also, in this group, there are many early 20s female customers, students, and self-employed people. This group customers show high word of mouth tendency, hence providing positive brand image to the customers would be important. In case of taste oriented group, while the scores of taste and location are high, word of mouth score is low. This group is mainly composed of educated and professional many late 20s customers, therefore, menu differentiation, increasing quality of coffee taste and price discrimination is critical to increase customers' satisfaction. However, it is hard to generalize the results of study to other coffee shop brand, because this study have researched only one domestic coffee shop, Caffe Bene. Thus if future study expand the scope of locations, brands, and occupations, the results of the study would provide more generalizable results. Finally, research of customer satisfactions of menu, trust, loyalty, and switching cost would be critical in the future study.

• Progress in Medical Physics
• /
• v.26 no.3
• /
• pp.160-167
• /
• 2015

Radiation exposure from medical diagnostic imaging procedures to patients is one of the most significant interests in diagnostic x-ray system. A miniature x-ray intraoral tube was developed for the first time in the world which can be inserted into the mouth for imaging. Dose evaluation should be carried out in order to utilize such an imaging device for clinical use. In this study, dose evaluation of the new x-ray unit was performed by 1) using a custom made in vivo Pig phantom, 2) determining exposure condition for the clinical use, and 3) measuring patient dose of the new system. On the basis of DRLs (Diagnostic Reference Level) recommended by KDFA (Korea Food & Drug Administration), the ESD (Entrance Skin Dose) and DAP (Dose Area Product) measurements for the new x-ray imaging device were designed and measured. The maximum voltage and current of the x-ray tubes used in this study were 55 kVp, and 300 mA. The active area of the detector was $72{\times}72mm$ with pixel size of $48{\mu}m$. To obtain the operating condition of the new system, pig jaw phantom images showing major tooth-associated tissues, such as clown, pulp cavity were acquired at 1 frame/sec. Changing the beam currents 20 to $80{\mu}A$, x-ray images of 50 frames were obtained for one beam current with optimum x-ray exposure setting. Pig jaw phantom images were acquired from two commercial x-ray imaging units and compared to the new x-ray device: CS 2100, Carestream Dental LLC and EXARO, HIOSSEN, Inc. Their exposure conditions were 60 kV, 7 mA, and 60 kV, 2 mA, respectively. Comparing the new x-ray device and conventional x-ray imaging units, images of the new x-ray device around teeth and their neighboring tissues turn out to be better in spite of its small x-ray field size. ESD of the new x-ray device was measured 1.369 mGy on the beam condition for the best image quality, 0.051 mAs, which is much less than DRLs recommended by IAEA (International Atomic Energy Agency) and KDFA, both. Its dose distribution in the x-ray field size was observed to be uniform with standard deviation of 5~10 %. DAP of the new x-ray device was $82.4mGy*cm^2$ less than DRL established by KDFA even though its x-ray field size was small. This study shows that the new x-ray imaging device offers better in image quality and lower radiation dose compared to the conventional intraoral units. In additions, methods and know-how for studies in x-ray features could be accumulated from this work.

• Tuberculosis and Respiratory Diseases
• /
• v.42 no.1
• /
• pp.58-66
• /
• 1995

Background: Acute interstitial pneumonia is a relatively rare form of interstitial pneumonia, since the vast majority of interstitial pneumonia have a more chronic course. It corresponds to the lesion described by Hamman and Rich, as Hamman-Rich disease in 1944. Another name in the clinical literature is accelerated interstitial pneumonia, idiopathic acute respiratory distress syndrome (idiopathic ARDS), and the organizing stage of diffuse alveolar damage. Acute interstitial pneumonia differs from chronic interstitial pneumonia by clinical and pathologic features. Clinically, this disease is characterized by a sudden onset and a rapid course, and reversible disease. Method and Purpose: Five cases of pathologically proven acute interstitial pneumonia were retrospectively studied to define the clinical, radiologic, and pathologic features. Results: 1) The five cases ranged in age from 31 to 77 years old. The onset of illness was acute in all patients, it began with viral-like prodrome 6~40 days prior to shortness of breath, and respiratory failure eventually developed in all patients. In 2 cases, generalized skin rash was accompanied with flu-like symptoms. Etiologic agent could not be identified in any case. 2) All patients had leukocytosis and severe hypoxemia. Pulmonary function test of 3 available cases shows restrictive ventilatory defect, and one survived patient(case 5) has a complete improvement of pulmonary function after dismissal. 3) Diffuse bilateral chest infiltrates were present radiologically. Theses were the ground-glass, consolidation, and reticular densities without honeycomb fibrosis in all patients. The pathologic abnormalities were the presence of increased numbers of macrophages and the formation of hyaline membranes within alveolar spaces. There was also interstitial thickening with edema, proliferation of immature fibroblast, and hyperplasia of type II pneumocyte. In the survived patient(case5), pathologic findings were relatively early stage of acute interstitial pneumonia, such as hyaline membrane with mild interstitial fibrosis. 4) Of the 5 patients, four patients died of respiratory failure 14~90 days after onset of first symptom, and one survived and recovered in symptoms, chest X ray, and pulmonary function test Conclusion: These results emphasize that acute interstitial pneumonia is clinically, radiologically, and pathologically distinct form of interstitial pneumonia and should be separated from the group of chronic interstitial pneumonia. Further studies will be needed to evaluate the pathogenesis and the treatment of acute interstitial pneumonia.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.31 no.3
• /
• pp.516-526
• /
• 2004

Polymerization shrinkage of photoinitiation type composite resin cause several clinical problems. The purpose of this study was to evaluate the shrinkage strain stress, linear polymerization shrinkage, compressive strength and microhardness of recently developed composite resins. The composite resins were divided into four groups according to the contents of matrix and filler type. Group I : $Denfil^{TM}$(Vericom, Korea) with conventional matrix, Group II : $Charmfil^{(R)}$(Dentkist, Korea) with microfiller and nanofller mixture, Group III : $Filtek^{TM}$ Z250(3M-ESPE, USA) TEGDMA replaced by UDMA and Bis-EMA(6) in the matrix, and Group IV : $Filtek^{TM}$ Supreme(3M-ESPE, USA) using pure nanofiller. Preparation of acrylic molds were followed by filling and curing with light gun. Strain gauges were attached to each sample and the leads were connected to a strainmeter. With strainmeter shrinkage strain stress and linear polymerization shrinkage was measured for 10 minutes. The data detected at 1 minute and 10 minutes were analysed statistically with ONE-way ANOVA test. To evaluate the mechanical properties of tested materials, compressive hardness test and microhardness test were also rendered. The results can be summarized as follows : 1. Filling materials in acrylic molds showed initial temporary expansion in the early phase of polymerization. This was followed by contraction with the rapid increase in strain stress during the first 1 minute and gradually decreased during post-gel shrinkage phase. After 1 minute, there's no statistical differences of strain stress between groups. The highest strain stress was found in group IV and followed by group III, I, II at 10 minutes-measurement(p>.05). In regression analysis of strain stress, group III showed minimal inclination and followed by group II, I, IV during 1 minute. 2. In linear polymerization shrinkage test, the composite resins in every group showed initial increase of shrinkage velocity during the first 1 minute, followed by gradually decrease of shrinkage velocity. After 1 minute, group IV and group III showed statistical difference(p<.05). After 10 minutes, there were statistical differences between group IV and group I, III(p<.05) and between group II and group III(p<.05). In regression analysis of linear polymerization shrinkage, group II showed minimal inclination and followed by group IV, III, I during 1 minute. 3. In compressive strength test, group III showed the highest strength and followed by group II, IV, I. There were statistical differences between group III and group IV, I(p<.05). 4. In microhardness test, upper surfaces showed higher value than lower surfaces in every group(p<.05).

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.41 no.2
• /
• pp.205-212
• /
• 2012

This study was performed to investigate the prevalence of metabolic syndrome (MS) and assess nutrient intake levels for the purpose of improving MS risk factors. The participants in this study were 512 adults consisting of 271 men and 241 women aged 30 and over, who visited a public health center for a medical check up. The diagnosis of MS subjects was adapted from the NCEP-ATPIII guidelines and the WHO Asia-Pacific Area criteria for obesity. The MS group was defined as subjects displaying three or more risk factors, and the non MS group was defined as those displaying two or less risk factors. A dietary survey was conducted using the 24-hour recall method. The number of subjects displaying MS syndrome factors was 158 (30.9%), broken down into, 89 men and 69 women. Regarding risk factors in the MS group, the prevalence of waist circumference was 40.5%, hypertension 34.2%, hyperglycemia 31.0%, low HDL-cholesterol 24.7%, and hypertriglycemia 19.6%. BMI, sistolic blood pressure, blood glocose, blood triglyceride, and blood HCL-cholesterol of the MS group were significantly higher compared to the non MS group. Male subjects in the MS group reported high intakes of cereals, sugar, fruits, meat and poultry, oil and fats, and beverages and total food intake was significantly higher compared to the non MS group. Women in the MS group reported high intakes of meat and poultry, milk and dairy products, beverages, and seasonings, and total food intake was higher compared to the non MS group. Dietary diversity score (DDS) was 3.82~4.04, which was not significant among the groups. In men, dietary variety score (DVS) was 16.3 in the MS group and 19.4 in the non MS group, whereas in women, the DVS was 15.2 in the non MS group and 17.0 in the MS group. In GMVDF pattern, 11111 pattern was 30.7%, followed by 01111 for men and 11101 for women. Calorie, fat, and cholesterol intakes in men as well as, calorie, fat, and folate intakes in women in the MS group were higher compared to the non MS group. Intakes of protein, P, Fe, Na, vitamin $B_1$, vitamin $B_2$, niacin, vitamin E, and Zn were higher than the KDRIs. On the other hand, intakes of Ca, K, fiber, vitamin $B_2$, and vitamin C were below the KDRIs. Intakes of lipids, animal food, Na, and cholesterol in the MS group were higher compared to the non MS group, whereas intake of dietary fiber was lower. Our results indicate that continuous, systematic nutritional education program must implemented to reduce the risk factors associated with MS.

• Tuberculosis and Respiratory Diseases
• /
• v.46 no.5
• /
• pp.697-708
• /
• 1999

Background : Leukotriene (LT) $C_4$, $D_4$, and $E_4$, the main components of slow-reacting substance of anaphylaxis (SRS-A), have been suggested to play an important role in bronchial asthma such as antigen-induced bronchoconstriction, airway hyperreactivity, and pulmonary eosinophil accumulation. The purpose of this study was to evaluate the effects of treatment with the cysteinyl-LTs (cys-LTs) antagonist, pranlukast on allergen-induced guinea pig asthma model. Methods : Guinea pigs of treatment and placebo groups were sensitized by subcutaneous injection of ovalbumin(OVA) and challenged by inhalation of aerosolized OVA (1% weight/volume OVA). Normal control group did not sensitize with OVA. Oral ingestion of pranlukast and normal saline to the treatment and placebo groups was performed. In the treatment and placebo groups, airway resistance was measured before and after oral ingestion. Serum $LTC_4$ and eosinophilic infiltration of the bronchiolar and peribronchiolar tissues were measured after ingestion in the treatment and placebo groups. Results : Allergen-induced airway constriction developed in 20 (8 in treatment group, 12 in placebo group) among 35 guinea pigs. Airway resistance was significantly decreased at 3 and 6 minutes after OVA challenge in the pranlukast treatment group. In the placebo group, there was no difference of airway resistance between before and after saline ingestion. Serum $LTC_4$ levels showed 348.4 pg/ml in the treatment group, 373.9 pg/ml in the placebo group, and 364.4 pg/ml in the control group. There were no statistically significant difference between treatment and placebo group (p=0.232), and treatment and control group (p=0.501). Eosinophilic infiltrations in the peribronchiolar region per one-microscopic field ($\times$400 high power fields) demonstrated 7.06 in the treatment group, 19.2 in the placebo group, and 4.50 in the control group. There was significant decrement of eosinophilic infiltration in the treatment group which was compared with placebo group (p=0.001). Conclusion : These results demonstrate that pranlukast, a cys-LTs receptor antagonist, can attenuate allergen induced early-phase bronchoconstriction and eosinophilic infiltration in the bronchiolar tissues.

• Journal of Intelligence and Information Systems
• /
• v.23 no.4
• /
• pp.127-146
• /
• 2017

Services using artificial intelligence have begun to emerge in daily life. Artificial intelligence is applied to products in consumer electronics and communications such as artificial intelligence refrigerators and speakers. In the financial sector, using Kensho's artificial intelligence technology, the process of the stock trading system in Goldman Sachs was improved. For example, two stock traders could handle the work of 600 stock traders and the analytical work for 15 people for 4weeks could be processed in 5 minutes. Especially, big data analysis through machine learning among artificial intelligence fields is actively applied throughout the financial industry. The stock market analysis and investment modeling through machine learning theory are also actively studied. The limits of linearity problem existing in financial time series studies are overcome by using machine learning theory such as artificial intelligence prediction model. The study of quantitative financial data based on the past stock market-related numerical data is widely performed using artificial intelligence to forecast future movements of stock price or indices. Various other studies have been conducted to predict the future direction of the market or the stock price of companies by learning based on a large amount of text data such as various news and comments related to the stock market. Investing on commodity asset, one of alternative assets, is usually used for enhancing the stability and safety of traditional stock and bond asset portfolio. There are relatively few researches on the investment model about commodity asset than mainstream assets like equity and bond. Recently machine learning techniques are widely applied on financial world, especially on stock and bond investment model and it makes better trading model on this field and makes the change on the whole financial area. In this study we made investment model using Support Vector Machine among the machine learning models. There are some researches on commodity asset focusing on the price prediction of the specific commodity but it is hard to find the researches about investment model of commodity as asset allocation using machine learning model. We propose a method of forecasting four major commodity indices, portfolio made of commodity futures, and individual commodity futures, using SVM model. The four major commodity indices are Goldman Sachs Commodity Index(GSCI), Dow Jones UBS Commodity Index(DJUI), Thomson Reuters/Core Commodity CRB Index(TRCI), and Rogers International Commodity Index(RI). We selected each two individual futures among three sectors as energy, agriculture, and metals that are actively traded on CME market and have enough liquidity. They are Crude Oil, Natural Gas, Corn, Wheat, Gold and Silver Futures. We made the equally weighted portfolio with six commodity futures for comparing with other commodity indices. We set the 19 macroeconomic indicators including stock market indices, exports & imports trade data, labor market data, and composite leading indicators as the input data of the model because commodity asset is very closely related with the macroeconomic activities. They are 14 US economic indicators, two Chinese economic indicators and two Korean economic indicators. Data period is from January 1990 to May 2017. We set the former 195 monthly data as training data and the latter 125 monthly data as test data. In this study, we verified that the performance of the equally weighted commodity futures portfolio rebalanced by the SVM model is better than that of other commodity indices. The prediction accuracy of the model for the commodity indices does not exceed 50% regardless of the SVM kernel function. On the other hand, the prediction accuracy of equally weighted commodity futures portfolio is 53%. The prediction accuracy of the individual commodity futures model is better than that of commodity indices model especially in agriculture and metal sectors. The individual commodity futures portfolio excluding the energy sector has outperformed the three sectors covered by individual commodity futures portfolio. In order to verify the validity of the model, it is judged that the analysis results should be similar despite variations in data period. So we also examined the odd numbered year data as training data and the even numbered year data as test data and we confirmed that the analysis results are similar. As a result, when we allocate commodity assets to traditional portfolio composed of stock, bond, and cash, we can get more effective investment performance not by investing commodity indices but by investing commodity futures. Especially we can get better performance by rebalanced commodity futures portfolio designed by SVM model.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.41 no.6
• /
• pp.1-19
• /
• 2013

This study tries to review 'Sakuteiki(作庭記)', the Book of Garden Making, compiled at the end of the 11th Century during the Heian Period of Japan, from the East-Asian perspective. 'Sakuteiki' is a Garden Theory Book, the oldest in the world as well as in Asia, and it contains the traditional knowledge of Japanese ancient garden culture, which originated from the continent(Korea and China). Traditional knowledge related to East-Asian garden culture reviewed in this paper is "Fungsu Theory"(風水, Asian traditional ecology: Fengshui in Chinese; Fusui in Japanese), stemmed from the culture to seek sound and blessed places to live in. Viewed from modern landscape architecture, the Fungsu Theory corresponds to ecology(science). The Fungsu Theory was established around the Han Dynasty of China together with the Yinyangwuxing(陰陽五行) Theory and widely used for making human residences including gardens. It was transmitted to Japan via Korea as well as through direct transaction between Japan and China. This study reinterprets garden design principles represented in Sakuteiki, which were selected in 5 key words according to the Fungsu Theory. The 5 key words for the Fungsu Theory are "the place in harmony of four guardian gods(四神相應地)", "planting trees in the four cardinal directions", "flow of Chi(氣)", "curved line and asymmetry", and "mountain is the king, water is the people". Garden design principles of "the place in harmony of four guardian gods(四神相應地)" and "planting trees in the four cardinal directions" are corresponding to "Myeongdang-ron(明堂論, Theory of propitious site)". The place in harmony of four guardian gods mentioned in Sakuteiki is a landform surrounded by the flow of water to the east, the great path to the west, the pond to the south, and the hill to the north. And the Theory originated from Zhaijing(宅經, Classic of dwelling Sites) of China. According to this principle, the city was planned and as a miniature model, the residence of the aristocrat during the Heian period was made. At the residence the location of the garden surrounded by the four gods(the flow of water, the great path, the pond, and the hill) is the Myeongdang(明堂, the propitious site: Mingtang in Chinese; Meido in Japanese). Sakuteiki explains how to substitute for the four gods by planting trees in the four cardinal directions when they were not given by nature. This way of planting originated from Zhaijing(宅經) and also goes back to Qiminyaoshu (齊民要術), compiled in the 6th Century of China. In this way of planting, the number of trees suggested in Sakuteiki is related to Hetu(河圖) and Luoshu(洛書), which are iconography of Yi(易), the philosophy of change, in ancient China. Such way of planting corresponds to that of Yongdoseo(龍圖墅, the villa based on the principle of Hetu) presented in Sanrimgyeongje (山林經濟), an encyclopedia on agriculture and living in the 17th Century of Korea. And garden design principles of "the flow of Chi(氣)", "curved line and asymmetry" is connected to "Saenggi Theory(生氣論, Theory of vitality)". Sakuteiki explains the right flow of Chi(氣) through the proper flow and the reverse flow of the garden stream and also suggests the curved line of the garden stream, asymmetric arrangement of bridges and stones in the garden, and indented shape of pond edges, which are ways of accumulating Chi(氣) and therefore lead to "Saenggi Theory" of the Fungsu Theory. The last design principle, "mountain is the king, water is the people", is related to "Hyeongguk Theory(形局論, Theory of form)" of the Fungsu Theory. Sakuteiki explains the meaning of garden through a metaphor, which views mountain as king, water as the people, and stones as king's retainers. It compares the situation in which the king governs the people with the help of his retainers to the ecological phenomena in which mountain(earth) controls water with the help of stones. This principle befits "Hyeongguk Theory(形局論, Theory of form)" of the Fungsu Theory which explains landform on the analogy of social systems, people, animals and things. As above, major garden design principles represented in Sakuteiki can be interpreted in the context of the Fungsu Theory, the traditional knowledge system in East Asia. Therefore, we can find the significance of Sakuteiki in that the wisdom of ancient garden culture in East-Asia was integrated in it, although it described the knowhow of a specific garden style in a specific period of Japan.