• Korean Journal of Materials Research
• /
• v.29 no.11
• /
• pp.703-708
• /
• 2019

In this study, we investigate the relationship between the peeling behavior of the backsheet of a photovoltaic(PV) module and its surface temperature in order facilitate removal of the backsheet from the PV module. At low temperatures, the backsheet does not peel off whereas, at high temperatures, part of the backsheet remains on the surface of the PV module after the peeling process. The backsheet material remaining on the surface of the PV module is confirmed by X-ray diffraction(XRD) analysis to be poly-ethylene(PE). Differential scanning calorimetry(DSC) is also performed to investigate the interfacial characteristics of the layers of the PV module. In particular, DSC provides the melting temperature($T_m$) of laminated ethylene vinyl acetate(EVA) and of the backsheet on the PV module. It is found that the backsheet does not peel off below the $T_m$ of ethylene of EVA, while the PE layer of the backsheet remains on the surface of the PV module above the $T_m$ of the PE. Thus, the backsheet is best removed at a temperature between the $T_m$ of ethylene and that of PE layer.

• Current Photovoltaic Research
• /
• v.9 no.1
• /
• pp.6-10
• /
• 2021

The mesh mask screen, which is generally used for screen printing metallization of silicon solar cell, requires high squeegee pressure and low printing speed. These requirements are acting as a limiting factor in production yield in photovoltaic industries. In order to improve the productivity, a metal mask, which has high durability and high printing speed, has been researched. In this paper, the characteristics of each solar cell, in which electrodes were formed by using a metal mask and a mesh mask, were analyzed through recombination current density. In particular, the metal-induced recombination current density (Jom) representing the recombination of the emitter-metal interface was calculated using the shading method, and the resulting efficiency and open-circuit voltage were analyzed through the diode equation. As a result of analyzing the proportion of the metal-induced recombination current density to the total emitter recombination current density, it was analyzed that the reduction of the metal-induced recombination current density through the metal mask is an important factor in reducing the total recombination current density of the solar cell.

• Journal of Hydrogen and New Energy
• /
• v.26 no.2
• /
• pp.96-104
• /
• 2015

Reactivity of commercial WGS catalyst and four new catalysts(RMC-3, PC-73, PC-67SU, PC-59) manufactured with various compositions by Korea Electric Power Research Institute(KEPCO RI) were compared to select suitable WGS catalyst for SEWGS system. Steam/CO ratio, gas velocity, flow rates of syngas, and temperature were considered as operating variables. As a result, commercial catalyst showed the highest CO conversion and RMC-3 catalyst showed also high CO conversion. Therefore, commercial and RMC-3 catalysts were selected as applicable catalysts. However, PC-73 catalyst showed low CO conversion at low temperature($200^{\circ}C$) but showed good reactivity at high temperature($225{\sim}250^{\circ}C$), and therefore, PC-73 catalyst was selected as applicable catalyst for high temperature operation. Continuous operations up to 24 hours for those three catalysts(commercial, RMC-3, PC-73) were conducted to check reactivity decay of catalysts. All three catalysts maintained their original reactivity.

• Particle and aerosol research
• /
• v.17 no.2
• /
• pp.29-36
• /
• 2021

In this study, the clean air delivery rate (CADR) of ceiling air circulator (CAA) was determined under indoor environmental simulation conditions. An air filter was used to provide air cleaning ability to the CAA. The CADR of filter adapted CAA was evaluated and compared with the value of commercial air purifier. The installation of mesh-shaped filter on the CAA showed particle reduction effect on the particles over 0.4 ㎛ in diameter, but the CADR was up to 0.25 m³/min. When the filter having 99.9% in collection efficiency was installed on the CAA, its CADR was 1.52 m³/min, while the CADR of commercial air purifier was 3.19 m³/min.

• Journal of Wind Energy
• /
• v.13 no.2
• /
• pp.13-22
• /
• 2022

In this study, the resonant motion of a floating offshore wind system due to negative damping was mitigated by peak shaving algorithms of the NREL ROSCO controller, and the decreased gains of the blade pitch controller by the gain detuning method for the floating system was increased to the gains of onshore baseline controller to improve the power performance of the turbine. To check the performance of the controller, the dynamic responses between the existing gain-detuned pitch controller and the ROSCO controller with peak shaving control for an OC4 floating offshore wind system were compared. As a result of DLC1.1 at near-rated wind speed, when peak shaving was applied, the average generator power decreased by 1.9%, but it was confirmed that the standard deviation was reduced and stability was improved with fast pitch regulation. In addition, since peak shaving reduces the maximum thrust of the rotor, was confirmed that not only are the loads of the blades and tower reduced, but the surge motion of the floater is also reduced, and the tension of the mooring lines is reduced.

• Current Photovoltaic Research
• /
• v.9 no.2
• /
• pp.23-30
• /
• 2021

Perovskite solar cells (PSCs) are currently attracting attention as a promising source of photovoltaic power generation for their rapid increase in efficiency within a short research period. However, the 2-step deposition method, which has been considered as a proper film fabrication route in commercialization point of view of PSC, requires a complicated control of environment to achieve high efficiency because each step of the process are affected by humidity in different manner. It is clearly a large hurdle for this technic to be transferred to industrialization. In this study, we developed a simple surface treatment by which high quality perovskite films can be fabricated through 2-step deposition method in a relatively wide humidity range without complicated humidity control at each step.

• Current Photovoltaic Research
• /
• v.10 no.4
• /
• pp.107-110
• /
• 2022

Lightweight and flexible photovoltaic (PV) modules are attractive for building-integrated photovoltaic (BIPV) applications because of their easy construction and applicability. In this study, we fabricated lightweight and flexible c-Si PV modules using ethylene tetrafluoroethylene (ETFE) front cover and shingled design string cells. The ETFE front cover instead of glass made the PV modules lighter in weight, and the shingled design string cells increased the flexibility. Finally, we fabricated a PV module with a conversion power of 240.08 W at an area of 1.25 m² and weighed only 2 kg/m². Moreover, to check the PV module's flexibility, we conducted a bending test. The difference of conversion power between the modules before and after bending shown was only 1.7 W, which showed a power reduction rate of about 0.7%.

• Current Photovoltaic Research
• /
• v.11 no.3
• /
• pp.75-78
• /
• 2023

Recently, the installation of photovoltaic modules in urban areas has been increasing. In particular, the demand for solar modules installed in a limited space is increasing. However, since the crystalline silicon solar module's size is proportional to the solar cell's size, it is difficult to manufacture a module that can be installed in a limited area. In this study, we fabricated a solar module with a shingled design that can control horizontal and vertical width using a bi-directional laser scribing method. We fabricated a string cell with a width of 1/5 compared to the existing shingled design string cells using a bi-directional laser scribing method, and we fabricated a solar module by connecting three strings in parallel. Finally, we achieved a conversion power of 5.521 W at a 103 mm × 320 mm area.

• Current Photovoltaic Research
• /
• v.10 no.1
• /
• pp.1-5
• /
• 2022

Bifacial photovoltaic (PV) technology has received considerable attention in recent years due to the potential to achieve a higher annual energy yield compared to its monofacial PV systems. In this study, we fabricated the bifacial c-Si PV module with a shingled design using the conventional patterned bifacial solar cells. The shingled design PV module has recently attracted attention as a high-power module. Compared to the conventional module, it can have a much more active area due to the busbar-free structure. We employed the transparent backsheet for a light reception at the rear side of the PV module. Finally, we achieved a conversion power of 453.9 W for a 1300 mm × 2000 mm area. Moreover, we perform reliability tests to verify the durability of our Shingled Design Bifacial c-Si Photovoltaic module.

• Current Photovoltaic Research
• /
• v.11 no.2
• /
• pp.54-57
• /
• 2023

Recently, requirements for improving the convenience of constructing BIPV (Building Integrated Photo Voltaic) modules had increased. To solve this problem, we fabricated shingled PV modules integrated with bent steel plates for building integrated photovoltaics. These PV modules could be constructed directly on the roof without the installation structure. We found optimal lamination conditions with supporting structures to fabricate a module on a bent steel plate. Moreover, we applied a shingled design to PV modules integrated with bent steel plates to achieve a high electrical output power. The shingled module with bent steel plates shows 142.80 W of solar-to-power conversion in 0.785 m² area.