• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.54-58
• /
• 2017

A combustion instability has been one of the most serious problems in the development of combustion devices including rocket engine and gas turbine. In particular, a high-frequency combustion instability generated by resonant coupling between combustion phenomena and acoustic oscillations within thrust chamber causes severe damage to the hardware. Because it is accompanied by high amplitude pressure oscillations and excessive heat flux to the chamber wall. Therefore, combustion instability is one of the difficult problems that must be resolved in developing liquid rocket engine. This paper describes the cases of combustion instability encounted during the development of thrust chamber for KSR-III and KSLV-II.

• Aerospace Engineering and Technology
• /
• v.1 no.1
• /
• pp.141-146
• /
• 2002

During dynamic flight by propulsion of rocket engine, in the atmosphere, the attitude control of flight vehicle can be accomplished by the aerodynamic fin actuator. But, in the outer space, the method of TVC(Thrust Vector Control) is only depend on for it. There are many systems which were developed for TVC. In our research, among them we adopted gimbal engine actuation system which could control the vector of thrust by swivelling rocket engine connected by gimbal. There are electro-hydraulic, electro-mechanical and pneumatic system which can be used as gimbal engine actuation system, but the electro-hydraulic system that has high ratio of output power to mass is preferred for the high power system. In this note, we made a mathematical model of the electro-hydraulic gimbal engine actuation system for the TVC of KSR-III in detail and on the base of this model we performed a simulation study. And then, we verified the model by making a comparison between the simulation and the experiments on the real system.

• Aerospace Engineering and Technology
• /
• v.2 no.2
• /
• pp.151-156
• /
• 2003

Liquid rocket engine system is classified into an engine of pressurization and turbo pump type by the way of fuel fed-supporting system. In the KSR-III sounding rocket, an engine of pressurization type was used, but there was lots of technical problems to be solved for a use as the first stage engine of space launch vehicle. So, an engine of turbo pump type was required to be developed to overcome the technical limitation of liquid rocket engine. In this research, the analysis of propellant of Kerosine-LOX and methane-LOX which are noticed as a future propellant was carried out for the purpose of studying the basic characteristics. And to review the basic characteristics of an engine of turbo pump type, among the sizing variant of the space launch vehicle, the ways of injecting a satellite to a direct orbit and transient orbit were discussed in this paper.

• Aerospace Engineering and Technology
• /
• v.2 no.1
• /
• pp.133-139
• /
• 2003

Position and trajectory data in-flight rocket are important informations to determine flight safety of rocket. In general tracking system, radar and transponder are used to acquire position information. Rocket position and trajectory can be determined by RF communication between ground station and in-flight rocket, and antenna position date. In this paper, it explains the ranging system which is low resolution rather than radar system but system configuration is simple. Therefore this system is useful for experimental flight vehicle.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.6
• /
• pp.14-20
• /
• 2002

The aerodynamic heating at a nose cone is predicted under the KSR-III flight conditions. An equilibrium reacting gas condition is applied. The parametric study is performed with Mach number of 4.9, 10.2 and 15 and for the following nose shapes of hemisphere, cut cylinder and parabola. AUSMPW+ and shock aligned grid technique are used to provide the best aerodynamic solutions. In addition, the composite material of a nose cone is discussed in the viewpoint of a thermal safety.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.723-725
• /
• 2010

Calculation program to predict required pressurant mass for propellant tank was verified through flight test data. This program was already developed and verified through ground test data, but to increase reliability of program, it was compared with flight test data of KSR-III launched in 2002. Because pressurant temperature incoming to propellant tank was not measured in flight test, that was assumed in calculation program. Required pressurant mass and inside temperature of oxygen tank dome was compared. Validation of calculation program was verified by showing required pressurant mass accuracy of 6%.

• 한국전산유체공학회:학술대회논문집
• /
• 2000.10a
• /
• pp.39-45
• /
• 2000

Hypersonic analysis on the KSR-III payload configuration has been performed using an axisymmetric Navier-Stokes code. A numerical code based on the Harten and Yee's upwind TVD scheme with simplified curve fits in the equilibrium chemically reacting air was developed. The carbuncle phenomenon on detached shock in front of the payload is controlled by using pressure gradients to tune the dissipation. Equilibrium chemically reacting computations for reentry flight conditions of Mach no. 10.2, 8, 4.9 are presented and compared with the results of calorically perfect gas.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.8
• /
• pp.54-63
• /
• 2004

The inner surface temperatures of the KSR-III Sounding Rocket launched at 29th November 2002 were measured in the flight test, and the aerodynamic heating rate and outer surface temperature were calculated. The used program is the MINIVER code, which calculate the boundary layer equation based on the theoretical analysis, and its calculation is simulated on the flight time histories. The analysis considered the inner surface heat transfer with one dimensional solid heat conduction. The results showed that the major interior heat transfer is the radiation heat transfer, and the maximum outer surface temperature due to aerodynamic heating reached to $223^{\circ}C$ at fin and the maximum heating rate is about $133kW/m^2$ at nose cap. The whole analysis proved that the surface temperature remained below the allowable temperature, and the KSR-III thermal design satisfies the thermal environmental conditions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.6 no.4
• /
• pp.47-58
• /
• 2002

The pressure regulator has been developed as a pressure-control device of propellant tank in KSR-III. The pressurization system of KSR-III is a basic pressurization system composed of pressurant, He tank and propellant tank. The pressure-control regulator is the most important part of gas-pressurized feed system along with He tank, pyrovalve and He fill valve. The first model of the regulator is tested to satisfy in leakage, strength and basic performance. The second model is tested in the overall test of the KSR-III propulsion system using water. From the test result of the second model, we conclude that the capacity of valve(Cv) must be increased in real system. The third model is modified and tested in the overall test of KSR-III propulsion system using propellant. Finally, the pressure-control regulator is qualified from firing test.

• Journal of Astronomy and Space Sciences
• /
• v.18 no.3
• /
• pp.249-256
• /
• 2001

KARI(Ko.ea Aerospace Research Institute) has measured the ionospheric electron temperature and density over the Korean Peninsular with the Langmuir and Electron Probe(LEP) onboard the Korean Sounding Rocket-II(KSR-II) In 1998. The purpose of LEP is to measure the electron density and temperature profile in the ionosphere. LEP consists of the Langmuir probe(LP) and the Electron temperature Probe(ETP) which are widely used for the measurement of the ionospheric plazma environment . We discuss the development of the Langmuir and Electron Probe which will be onboard the KSR-III and some test results in a simulated space plasma environment with the plasma chamber at the ISAS in Japan. These measurements could contribute to the basic study of ionospheric environment which also can be compared with other reference models such as IRI and PIM.