• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.2
• /
• pp.115-121
• /
• 2002

This report summarized the static test of the rudder system for the KTX-1 basic trainer. The test loads are applied up to the limit and ultimate loads in a stepping sequence. Test loads and test results matt the strength and stiffness requirements of the rudder control system.. Using #004 full scale structure test airframe.

• Journal of Aerospace System Engineering
• /
• v.15 no.1
• /
• pp.80-85
• /
• 2021

In this study, for conducting a static load test of an external fuel tank used for an aircraft, the flight load acting on the external fuel tank was converted to the test load and the suitability of the converted test loads was confirmed. In order to calculate the test load from the flight load, the external fuel tank was divided into several sections. Shear load, moment by unit shear load, and unit moment were calculated for each section. Test loads for each section were then calculated by computing the shear load, the moment of each section, and flight load condition. In actual static load tests, it might not be possible to impose the test load in the calculated position due to physical constraints. Therefore, after determining positions in which the load could be imposed in the actual test, the test load calculated for each section was redistributed to selected positions. Finally, a test load plan was established by applying a whiffle tree to enhance the efficiency of the test performance while making it easier to operate the actuator. The reliability of the test load plan was verified by comparing it with flight load conditions.

• Aerospace Engineering and Technology
• /
• v.10 no.2
• /
• pp.146-153
• /
• 2011

Some methods of calculation of test load value from design load data were investigated which will be applied at strap installed full-scale airframe of composite aircraft. These methods were applied to left wing of KC-100 composite aircraft and the calculated test load values were compared with each others. Generally since test load values are differently calculated according to each aircraft type and position of straps, all calculation methods mentioned at this study need to be applied and compared to each aircraft. Finally the most appropriate method needs to be selected.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05c
• /
• pp.284-289
• /
• 1996

국산 원자로 압력용기강(ASME SA508 cl.3)을 대상으로 표준 샤피충격시험편(2 mm V- notch)과 피로균열(precracked Charpy) 시험편을 제작하여 계장화(instrumented)충격시험을 실시하고, 충격시험시 하중점(load point)의 변위(displacement) 혹은 시간의 변화를 하중의 변화와 함께 측정하였다. 측정결과를 파괴현상 및 파괴역학과 연계시켜 해석하므로서, 가능한한 소량의 시험편(혹은 시험공정)을 사용하여 필요로 하는 인성평가 관련 정보를 획득할 수 있도록 시도하였다. 그 결과, 파괴과정을 나타내는 하중의 변화를 이용하여 Shear fraction 을 예측할 수 있었고, 하중의 변화와 관계된 변위로부터 Lateral expansion을 추정할 수 있었다. 피로균열 시험편 시험결과로 부터는 충격시의 항복하중, 항복변위, 최고하중 등을 획득하여 균열크기의 함수로 표시되는 시험편 Compliance 를 계산하였고, Equivalent energy 법과 J-integral 법을 적용하여 원자로 압력용기강의 탄소성 동적파괴인 성을 평가할 수 있었다.

• Aerospace Engineering and Technology
• /
• v.3 no.2
• /
• pp.208-216
• /
• 2004

Advanced overload protection module for full scale airframe structural test was developed by improving the existing overload protection module. When performing the full scale airframe structural test, overload can be applied to the test article due to unexpected situations such as system shutdown, test article failure, and deficiency of design strength. Therefore, the overload protection module is needed for protecting the test article in unexpected overload situations. In this paper, the function of the existing overload protection module was summarized for each component and the problems encountered when using it in structural test were analyzed in addition, the development of advanced overload protection module was described.

• Aerospace Engineering and Technology
• /
• v.11 no.1
• /
• pp.7-18
• /
• 2012

Full-scale static test was introduced for the KC-100 aircraft which is domestic civil aircraft to be certified for the first time. Test requirement, test frame, and important test stystems such as loading system, counterbalance system, restraint system and jacking system are explained in detail. Especially, the way to satisfy compliance for the installation of test article and loading system is introduced by using check sheets for the installations. 15 Full-scale and 7 local test conditions were successfully completed and the test data was obtained.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 1999.06a
• /
• pp.181-186
• /
• 1999

반복하중에 따른 P.C 구조물의 장착장치로 사용되는 Wedge 형상에 따른 거동특성을 파악하기 위하여 정적최대하중을 이용하여 피로시험을 수행하였다. 또한 피로시험 결과로부터 반복회수에 따른 시험 체의 균열양상, 하중-변위, 하중-변형율, 하중-중앙 최대 변위, 하중-영구 변형량, 반복횟수에 따른 S-N선도 등을 고찰하였다. (중략)

• Journal of the Korean Geotechnical Society
• /
• v.16 no.6
• /
• pp.161-172
• /
• 2000

자연암석절리 및 인공 절리에 대하여 일정수직응력제어, 일정 수직하중제어 그리고 무한 강성제어가 가능한 암석 절리면 전단기 시험기를 개발하였다. 이 시험기는 전단변위에 의한 첩촉면적의 변화량을 계산하여 하중변화량을 조절하여 일정수직응력상태를 유지한다. 수직하중에 따른 시험기 강성에 의한 변화향이 제어 프로그램 내에서 제어되어 순수한 시편의 변위량을 출력하도록 하였다. 전단하중에 따른 시험기 강성에 의한 변위량은 상, 하부 전단상자의 상대변위 측정으로 최소화하였다. 전단거동 중의 자유도는 전당방향에 대하여 수평이도, 연직이동, 피칭, 롤링이 가능하도록 하였다. 자연절리면을 모사한 석고시편에 대하여 일정 수직응력 제어, 일정수직하중제어 그리고 무한 강성제어 조건으로 시험하여 제어상태 검증 및 비교를 하였다. 또한 경사각이 16.7˚와 22.6˚인 톱니형 시편에 대하여 시험한 결과 경사각 16.7˚와 22.6˚는 JRC로 10과 15를 나타내었으며, 첨두팽창각이 첨두전단강도에서 발생되며, Barton의 모델과 잘 일치함을 보였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.3
• /
• pp.82-87
• /
• 2004

The general requirements to achieve the structural integrity of the airframe are described in the military specification, MIL-HDBK-1530. One of these requirements is the durability and damage tolerance of the airframe, which should be shown through the analysis and test based on the related specifications. This paper describes the full scale durability test load simulation to evaluate the structural safety and durability of the advanced trainer, T-50. The test load simulation was performed according to the procedure in the military specification and the KAF contract requirements. The durability test design technique which involve the floating test set-up, the optimal test load simulation method, and the 6-DOF test article balance method to secure the real flight conditions as many as possible. It was confirmed that this method will be available in a similar full-scale airframe structural test in future.

• Journal of Aerospace System Engineering
• /
• v.15 no.5
• /
• pp.98-105
• /
• 2021

This study presented the results of the static load tests conducted to verify the structural robustness of the composite oxidant tank for a space launch vehicle. First, we introduced the test equipment used in the static load test of the composite oxidant tank, and then described the test requirements that the composite oxidant tank must satisfy. In addition, we presented a test set-up diagram consisting of the static load test fixture, hydraulic pressure, control equipment, and data acquisition equipment, and the load profile of the static load test of the composite oxidant tank consisting of shear, equivalent compression, bending, and combination tests. As a result of load control, we verified the reliability of this test by showing the errors between the input load and the feedback load in each channel according to the increase of the test load, and the feedback error between the channel A and channel B of load cell in each load actuator. As a result of the static load test, the load of the actuator was properly controlled within the allowable error range in each test, and we found that the test specimen did not cause damage or buckling that causes significant structural defects in the required load.