• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.282-285
• /
• 1999

The (1-x)MgTiO$_3$-xSrTiO$_3$(x=0,0.1) ceramics were prepared by the conventional mixed oxide method. The structural properties were investigated with sintering temperature and composition ratio by XRD, SEM and DT-TGA. Increasing the sintering temperature from 130$0^{\circ}C$ to 1$600^{\circ}C$, second phase was decreased and grain size was increased. In the case of 0.9 MgTiO$_3$-0.1SrTiO$_3$ ceramics sintered at 130$0^{\circ}C$, dielectric constant, quality factor and temperature coefficient of resonant frequency were 22.61, 10,928(at 1GHz), +50.26ppm/$^{\circ}C$ , respectively.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1997.10a
• /
• pp.75-80
• /
• 1997

Ethanol을 용매로 사용한 iron(III) Nitrate(Fe(NO$_3$)$_3$.9$H_2O$) 용액의 가수분해 반응에 의해 $\alpha$-Fe$_2$O$_3$미분말을 합성하였다. 가수분해 정도를 알아보기 위해 pH 변화를 측정하였으며, 반응온도와 iron(III) nitrate의 농도를 변화시켜 각각이 입자크기에 미치는 영향을 관찰하였다. 하소 후의 XRD pattern을 관찰하여 $\alpha$-Fe$_2$O$_3$결정상의 생성을 확인하였으며, 미세구조 관찰 결과 얻어진 $\alpha$-Fe$_2$O$_3$분말은 50nm이하의 미세한 입자임이 확인되었다.

• Journal of the Korean Ceramic Society
• /
• v.22 no.1
• /
• pp.47-52
• /
• 1985

The effect of calcining temperature on planar coupling factor Kp resonance and antiresonance frequency of $Pb(Z_{0.53}Ti_{0.47})O_3$ doped with $Nb_2O_5$ has been investigated. The calcining temperature ranged from $700^{\circ}C$ to 110$0^{\circ}C$ The calcining temperature affected on antiresonance frequency more strongly than the resonance frequency. Therefore the Kp was almost entirely dependent upon the antiresonance frequency. The p and antiresonance frequency of the sample in creased with the calcining temperature reaching a maximum at about 90$0^{\circ}C$ When a poling electric field of 35KV/cm was applied to the sample calcined at 90$0^{\circ}C$ and sintered for two hours at 120$0^{\circ}C$ Kp attained a maximum value of 0.64 which is in good agreement with the results of other investigators.

• Journal of the Korean Ceramic Society
• /
• v.22 no.1
• /
• pp.40-46
• /
• 1985

The effect of calcining temperature ranged from $700^{\circ}C$ to 110$0^{\circ}C$ on sintering characteristics of morphotropic $Pb(Zr_{0.53}Ti_{0.47})O_3 doped with $Nb_2O_5$ has been investigated. The ratio of sintered grain size to calcined grain size decreased as the calcining temperature increased. The hardness as well as the sintered density of the samples reached a maximum at about 90$0^{\circ}C$. The X-ray diffraction pattern of the sintered sample showed both tetragonal and rhombohedral phases. The tetragonal phases intensity increased with the calcining temperature going through a maximum at about 90$0^{\circ}C$ while the rhombohedral phase intensity remained uneffected. The both intensity were about the same at 90$0^{\circ}C$ The dielectric constant of the sintered samples reached a maximum um while the dielectric dissipation factor showed a minimum at the calcining temperature of about 100$0^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.24 no.5
• /
• pp.423-430
• /
• 1987

Characteristics of Al2O3-ZrO2 powders prepared by sol-gel process and their sintering behavior were investigated as a function of calcination temperature. The sol-gel processed powders were calcined at 800, 900, 1000, 1100, 1200$^{\circ}C$, and analyzed by X-ray diffraction technique. Pore size and distribution of green compact of the calcined powders were measured by mercury porosimeter. It is suggested that the optimal temperature of calcination for the sintering of Al2O3-ZrO2 powder prepared by sol-gel process is 1100$^{\circ}C$. In the Al2O3-17vol.% ZrO2 sintered specimen, which was sintered at 1600$^{\circ}C$ for 2hrs in air, 69vol.% tetragonal phse existed.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.228-231
• /
• 2004

The purpose of this study evaluates possibilities of waste phosphogypsum into concrete by steam curing admixture. The waste phosphogypsums were classified into 4 forms(Dihydrate, $\beta-Hemihydrate$, III-Anhydrite and II-Anhydrite) which were changed to in low temperature of calcination. Also, various admixtures were made of waste phosphogypsum(PG) and pozollanic fine powderers (Fly-ash, Blast Furnace Slag), and the basic properties of the cement mortars incorporating with these admixtures were examined and analyzed under a verity of experimental conditions. As a result, III-Anhydrite, these is similar to II-Anhydrite from compressive strength and are great in the effect of strength improvement. also, it was proved that specimens made on type III-Anhydrite of waste phosphogypsum and blast furnace slag increased on the compressive strength of cement mortar. Therefore, III-Anhydrite phosphogypsum calcined at lower temperature could be used as steam curing admixture for concrete 2th production.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.2 no.1
• /
• pp.60-69
• /
• 1992

Fine $TiO_2$ powders were synthesized from ammonium titanium sulphate which produced from $TiCI_4$, and$(NH_4)_2$ SO. solution. Rutile single crystal were grown by the verneuil method with anatase powders and investigated the property of rutile crystal. The optimun growing conditions were as follows $\cdot$The ratio of hydrogen gas and oxygen gas; 3: 1 $\cdot$Growing temperature: $1900^{\circ}C$ $\cdot$The feeding rate of powders: 10g/hr

• Journal of the Korean Ceramic Society
• /
• v.32 no.1
• /
• pp.1-10
• /
• 1995

Effects of calcination temperature on microstructure and electric-magnetic properties of Mg-ferrite were investigated. As the calcination temperature increase, the green density and the sintered density increase due to the enhancement of densification of calcined powder. The grain size in the sintered ferrite increases with increasing the calcination temperatures from 800 to 100$0^{\circ}C$, but decreases from 1000 to 120$0^{\circ}C$. The resistivity decreases with increasing the calcination temperatures from 800 to 110$0^{\circ}C$, but increases from 1100 to 120$0^{\circ}C$ due to the microstructure which consists of small, uniform grian size and pores at grain boundaries. Magnetization increases slightly due to the increasement of the sintered density while Curie temperature is almost constant regardless of calcination temperatures.

• Journal of the Korean Ceramic Society
• /
• v.23 no.6
• /
• pp.66-70
• /
• 1986

The calcining temperature ranging from 900$^{\circ}C$ to 1300$^{\circ}C$ affected on the planar coupling factor and resonance characteristics of BaTiO3 ceramics doped with 0.2 wt% MnO2 have been investigated. Dielectric constant planar coupling factor and anti-resonance frequency of the sample increased with the calcining temperature up to 1,200$^{\circ}C$ and decreased above that temperature but the resonance frequency decreased slightly with the increasing calcining temperature. The planar coupling factor and anti-resonance frequency increased with the sintered density and dielectric constant while the resonance frequency was almost constant. The resonance and anti-resonance frequency increased with the sample temperature.

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.659-667
• /
• 1997

The effect of calcination temperature of Mg(OH)2 on the green density and densification of MgO was investigated. It was observed that the impure magnesium hydroxide powder showed a higher crystallization rate while it had a lower tendency of agglomeration between periclae crystallites, as compared to that of the pure magnesium hydroxide powder. In the case of calcination of the powders under 85$0^{\circ}C$, the impure powder showed the higher green and sintered density. In spite of higher green density upon the calcination over 100$0^{\circ}C$, the impure powder showed the lower sintered density, caused by exaggerated growth of the periclase crystallites. The highest sintered densities in the both powders were obtained at the calcination temperature of 100$0^{\circ}C$. And the green density was inversely proportional to the sintered density at the calcination over 100$0^{\circ}C$.