본 논문에서는 콘센트의 품질이나 기능이 비약적으로 발전하였으나, 기존 노출형 콘센트에 플러그를 연결하는 경우에 쉽게 빠지는 경우가 발생하거나, 콘센트와 플러그가 외부에 바로 노출되어 있어 먼지나 수분에 취약한 문제가 있어 그 해결책을 해결하고자 하였다. 콘센트와 플러그 사이에 콘센트 고정 장치를 결합하는 방법을 제시하고, 매입형 콘센트의 경우에도 고정 장치를 쉽게 결합하여 빠지는 현상을 방지하고, 먼지나 수분에 의한 감전사고 예방 효과를 누릴 수 있는 제품을 개발하고자 하였다.
Journal of the Institute of Electronics Engineers of Korea SC
/
v.48
no.4
/
pp.47-53
/
2011
The Electric Multiple Unit (EMU) has many types of door system such as sliding door, plug door etc.al. according to customer's requirements. The sliding door is widely used in Korea but has weak point in the noise problem. In the low operation speed, the noise coming from outer side of the EMU is not an important factor. As the speed is higher than before, noise is increased and make a problem. The main cause of noise is the imperfect air tightness in the EMU. The plug door system has advantages for the noise reduction characteristic in the high speed area. We have been developing electric plug-in door. The door is controlled by Door Control Unit(DCU) following the order of Automatic Train Protection (ATP) that is a kind of train signalling system. DCU has to simultaneously open and close the doors and the operation of it is related to the passengers safety. So DCU is a safety device that is important to reliability and safety. DCU is composed of several devices of control, motor driving, Input/Output, communication and power. In this paper, we will describe the functions, characteristic, requirement, subsystem and test results of DCU used for the electric plug-in door.
This study conducted tunnel blasting to evaluate the blasting effect of a shear thickening fluid-based blasting stemming material and a sealed plug device under development. STF single stemming and STF stemming materials were combined with plugs to a tunnel blasting to which the SAV-Cut method was applied, and the advanced rate and fragmentation of tunnel blasting muck pile were compared when sand stemming was used. Tunnel advanced rate was evaluated using a 3D laser scanner. When the STF stemming material and STF stemming material with the plug were compared to the sand stemming material, it increased by 5.7 and 5.36%, respectively. As a result of evaluation of the fragmentation of tunnel blasting muck pile, it was the best when the STF stemming material was applied, and it decreased by about 61% compared to the case of sand stemming blasting. However, no significant improvement in blasting effect was observed with the application of plug devices.
Numerical simulation is the most widely used methods for evaluating blasting performance. This study, conducted the numerical analysis of shock chamber model to evaluate the pressure confine effect of the stemming material and plug device. The stemming effect was compared and evaluated with that of the STF-based stemming material currently under development and sand, which is a commonly used blast stemming material. Furthermore, to verify of enhancement the confine effect inside blast hole pressure, three types of stemming plugs were adopted for the numerical analysis. The numerical simulation results revealed that the STF-based stemming materials were superior to the general stemming material. Also, It is evaluated that the STF-based stemming and Plug system can not only prevent detonation gas from overflowing the borehole prematurely, but also prolong the action time and scope of detonation gas in the borehole effective.
In this paper, the function design of smart media platform control with smart monitoring, and displaying modules which have the priorities of smart plug based smart outlet, is proposed for electrical suppliance of essential information appliance in emergency power consumption situation(blackout, peaktime etc). The effect of power management will be maximized by this smart gateway interlocking with ESS(energy storage system) which has bi-directional power transmission control modules, and smart outlet based on the priority control actions.
Journal of Korea Society of Industrial Information Systems
/
v.20
no.4
/
pp.47-54
/
2015
With the spread of smart technology, in the personal and office equipment, many of the products are equipped with smart features. These changes have opened the era that can enforce the user's operation from a remote location. In this study, we design and implement a smart multi-plug system to make a multi-plug installed in the home can be operated anytime and anywhere via wireless network technologies add smart feature to a multi-plug that can be seen easily around us, it is intended to complement the limitations of traditional multi-plugs. The smart multi-plug proposed in this paper, by operating the plug remotely from smart devices at anytime and from anywhere, is possible to provide services required for the weak users such as elderly and children, it is expected that the proposed system are widely used in the various areas requiring remote control of the power supply including u-Farming, terrarium, and smart home, and so on.
Proceedings of the Korea Institute of Fire Science and Engineering Conference
/
2011.11a
/
pp.27-30
/
2011
본 논문은 플러그 충전부 형태에 따른 트래킹 발생특성을 분석하고자 현재 국내에서 시판되고 있는 플러그 중 형태가 서로 다른 플러그들을 시료로 선정하여 충전부간 거리에 따른 트래킹 특성을 KS C IEC 60112에 의거하여 실험을 실시하였다. 또한 모형 트래킹 실험장치를 제작하여 염해환경에서의 플러그 충전부간 트래킹 특성을 관찰하였고, 플러그에 가해지는 전압은 수전설비의 변압기 결선 형태에 주로 사용되는 단상 3선식과 단상 2선식의 형태로 인가하여 결선 형태에 따른 위험성을 추가적으로 분석하였다.
네트워크 통신(network communication)을 위해서는 개별 정보가전기기의 전원인가 상태가 상시 유지되어야 하는 문제점을 가지고 있다. 이러한 문제를 극복하기 위해, 통신요청시에는 그 때마다 통신동작이 가능하도록 충분한 전력공급을 제공하는 절대조건을 만족시키는 반면, 통신대기시에는 최소한의 전력만이 공급됨으로서 해서 초절전을 실현할 수 있는 정보가전기기의 PLC통신모듈용 전원장치를 먼저 개발하였다. 그리고, 최근 절전이 강조되고 있은 시점에서, 제품자체의 절전기능이 포함되어 전기에너지를 절약할 수도 있지만, 사용자의 절전의지와 행위에 의해서도 전기에너지를 절약할 수 있다. 이러한 관점에서 볼때 본 연구개발에서는, 제품의 전원플러그를 콘센트에 꽂는 과정에서 콘센트와 전원플러그 사이에 전기에너지량을 계측할 수 있는 전자회로 및 계측값을 나타내는 표시장치 그리고 필요에 따라서 통신기능을 포함하는 전기콘센트 단위의 Electric Energy Metering Sensor(이하 EEMS) 모듈을 개발하였다.
Proceedings of the Korean Society for Agricultural Machinery Conference
/
2017.04a
/
pp.128-128
/
2017
현재 식물공장에서 사용되고 있는 이식장치는 핀을 이용하여 육묘트레이 위에서 플러그묘를 뽑아 육묘트레이 또는 포트로 옮겨 심는 방식을 채택하고 있다. 이러한 이식 방식은 셀과 셀 사이에 있는 다른 묘의 잎을 파지함으로써 묘를 2개 이상 취출하는 현상이라든지 핀에 의한 잎 손상 등이 우려되고 있어 이에 대한 개선책이 필요하다. 본 연구는 플러그묘의 이식작업 시 잎 손상을 줄이면서 기계 적응성을 향상시킬 수 있는 이식시스템을 개발하기 위해 진공흡인을 이용한 이식 메커니즘에 대해 검토하였다. 플러그묘 이식시스템은 육묘트레이 셀을 X-Y로 옮기는 묘 이송부, 육묘트레이의 셀 하단으로부터 진공을 발생시켜 묘를 떨어뜨리는 진공 흡인부, 낙하되는 묘를 감지하는 센서와 블로워 및 공압 실린더로 구성된 진공 발생부, 혈공된 포트를 진공 발생부의 유도관으로 옮기는 포트 이송부 등으로 설계 제작하였다. 이식 메커니즘은 육묘트레이 하단부로부터 플러그묘를 1개씩 진공흡인하는 방식을 채택하였고, 이를 위해 상하 모두 개방된 72공 육묘트레이($L538{\times}W280{\times}H45mm$)를 윗부분(Ø35mm) 보다 아랫부분(Ø37mm)의 셀이 넓은 형상으로 PP재질의 육묘트레이를 사출금형 제작하였다. 묘 이송부에 장착된 플러그묘는 X축 방향(12개 셀)으로 이식작업이 이루어지고, Y축(6개 셀)으로 이동된 후 다시 동일한 방향으로 연속 작업이 가능하도록 제어프로그램을 구성하였다. 이식 원리는 진공 흡인부에 플러그묘가 이송되면 진공 발생부의 흡착패드가 위로 전진하여 진공을 발생시켜 묘를 흡인하고, 유도관 내에 부착된 광화이버센서에 의해 묘를 감지하여 블로워와 공압실린더를 제어함으로써 이식 공정이 끝나게 된다. 로메인상추의 플러그묘를 대상으로 진공흡인 시험을 실시한 결과 묘 손상없이 이식작업이 가능한 것으로 확인되었다.
Since plug type passenger door has two motion modes, power transmission unit must be capable of plug-in or plug-out, and sliding mode. Complex planetary gear train is proposed, which is composed of two 2K-H, I type planetary gear units. For the proposed complex planetary gear train, ranges of addendum modification coefficients which would not lead to interferences is analyzed, and optimal addendum modification coefficients among these ranges which generate the maximum efficiency are presented. Based on the interference, efficiency and torque ratio analysis results, complex planetary new train is designed and manufactured.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.