• 한국해양공학회지
• /
• 제16권4호
• /
• pp.37-41
• /
• 2002

선박해양 구조에 사용되는 대부분의 알루미늄 헬리데크는 외제로 관련 구조해석에 대한 정보도 일차적으로 외국의 전문업체가 제공하고 있고, 조선소에서는 필요시 주로 하부구조 해석을 보완하고 있다. 본 논문에서는 외국의 해석기술을 분석하고, 데크를 구성하고 있는 알루미늄 플랭크와 하부구조에 대한 구조해석을 수행하여 유사한 결과를 도출하였고, 해석에 관한 경험을 축적하였다.

• 대한통합의학회지
• /
• 제6권3호
• /
• pp.25-32
• /
• 2018

Purpose : This study investigated the effects of different types of plank exercise on abdominal muscle thickness in subjects with asymmetric pelvic anterior tilt. Methods : Participants with a diagnosis of pelvic anterior tilt were divided into an experimental group (n=12) and a control group (n=13). The thicknesses of the transverse abdominis (TrA), internal oblique (IO), and external oblique (EO) muscles were measured using an ultrasound diagnostic apparatus. The data were analyzed using an SPSS (Ver. 21) program. Results : In the experimental group, there was a significant difference in the thicknesses of the left and right muscles in the standing and elbow plank exercises (p<.05). All the muscle thicknesses increased significantly during the plank exercises(elbow plank, right-side plank, and left-side plank) as compared with those in the standing position (p<.05). In addition, the side-plank exercise resulted in significantly higher muscle thickness of the supported side (p<.01, p<.001). Conclusion : These findings suggest that asymmetric exercise should be applied to the change of the left and right muscles of the abdominal when applying plank exercise according to pelvic anterior tilt.

• 한국공작기계학회논문집
• /
• 제12권3호
• /
• pp.8-16
• /
• 2003

Monitoring of the drill wear :md hole quality change is conducted during the drilling process. Cutting force measured by tool dynamometer is a evident feature estimating abnormal state of drilling. One major difficulty in using tool dynamometer is that the work-piece must be mounted on the dynamometer, and thus the machining process is disturbed and discontinuous. Acoustic transducer do not disturb the normal machining process and provide a relatively easy way to monitor a machining process for industrial application. for this advantage, AE signal is used to estimate the abnormal fate. In this study vision system is used to detect flank wear tendency and hole quality, there are many formal factors in hole quality decision circularity, cylindricity, straightness, and so of but these are difficult to measure in on-line monitoring. The movement of hole center and increasement of hole diameter is presented to determine hole quality. As the results of this experiment AE RMS signal and measurements by vision system are shorn the similar tendency as abnormal state of drilling.

• 한국정밀공학회지
• /
• 제26권5호
• /
• pp.48-56
• /
• 2009

In this paper, laser-assisted machining(LAM) has been employed to machine hot isostatically pressed (HIPed) Si3N4 work pieces. Due to little residual flaws and porosity, HIPed $Si_3N_4$ work pieces are more difficult to machine compared to normally sintered $Si_3N_4$ workpieces. In LAM, the intense energy of laser was used to enhance machinability by locally heating the workpiece and thus reducing yield strength. In experiments, the laser power ranges from 200W to 800W and the diameter of work pieces is 16mm. While machining, the surface temperature was kept nearly constant by laser heating except for a short period of rise time of max. 58 seconds. Results showed as feed rate increases the surface temperature of $Si_3N_4$ workpieces decreases slightly, whereas the effect of depth of cut is disregardable. With a laser power of 800W, achievable maximal depth of cut as 0.7mm and feed rate was 0.03mm/rev.

• 한국정밀공학회지
• /
• 제18권9호
• /
• pp.89-95
• /
• 2001

Ceramic tool has to equip with not only high toughness and strength but also low thermal expansion and good thermal conductivity which leads to the high thermal shock resistance. These characteristics make it have longer tool life under thermal stress condition. In this study, commercial Si$_3$N$_4$ceramic cutting tool and home-made SiC based ceramic cutting tools which have different sintering time and chemical composition are tested under various cutting speed and the feed rate increase, the cutting force and the flank wear growth ratio increase, too. The performance of home-made SiC based ceramic cutting tool shows the possibility to be a new ceramic tool.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.59-65
• /
• 2003

Four kinds of $Si_3N_4$-based ceramic cutting tools with different sintering time were fabricated to investigante the effect of sintering time on the microstructure, mechanical properties, grain sizes and the cutting performance. An endeavor was also made to determine the relation among mechanical property, Brain size and tool life. $Si_3N_4$ home made cutting tool sintered for 1 hour under $1760^{\circ}$ temperature and 25MPa pressure showed the best cutting performance among selected ceramic tools during machining both Bray cast iron and heat treated SCM440. Multiple linear regression model was used to estimate the tool lift from mechanical property, grain size and showed good result. It was also shown that hardness imposed the biggest offect on tool life.

• 설비공학논문집
• /
• 제13권5호
• /
• pp.377-387
• /
• 2001

This paper presents leakage characteristics of a scroll compressor applying alternative refrigerants of R22 such as R407c and R410a under actual operating conditions. Because leakage in a scroll compressor produce significant losses and degradation of performance, those should be clarified to design a high efficient scroll compressor with alternative refrigerants of R22. However, flank and tip leakage characteristics of a scroll compressor with alternative refrigerants are very limited in open literature. In the present study, both experimentation and modeling of the leakages in the scroll compressor were performed. As a result, it was observed that the leakages of the scroll compressor with R407c increased by 15%, and that with R410a increased by 76% as compared to the compressor applying R22 under standard load conditions due to a higher upstream pressure and a higher pressure difference between pockets.

• 한국임상보건과학회지
• /
• 제7권2호
• /
• pp.1318-1324
• /
• 2019

Purpose. The study was conducted to find out the effects that women in their 20s with abdominal obesity can get from sling-based flanks. Methods. The study used In-Body to determine the weight and body fat rate of women in their 20s who were overweight at H University and used a tape measure to measure the circumference of the abdomen. Plank exercise using slings to reduce weight, body fat and abdominal circumference led to muscle stabilization and abdominal obesity reduction. The collected data were analyzed using the SPSS ver. 23.0 statistics program. Results. The results of the study showed statistically significant differences in the weight, body fat rate and abdominal circumference of the subjects before and after intervention. Conclusions. Steady abdominal muscles exercise help stabilize the abdomen, reduce abdominal body fat rate, and are effective in managing obesity.

• 한국기계가공학회지
• /
• 제10권2호
• /
• pp.73-78
• /
• 2011

The existent cutting insert have occupied most product of grinding style, because it has a problem of accuracy and manufacturing process. The product has a concept but development is difficult, because grinding and manufacturing by press are impossible. But by development and stabilization of a technology, preference of non-ground insert increases gradually. And then insert that grinding is impossible is developed availably as non-ground product by using developed equipment and software. In this paper reports some experimental results on the machining performance of non-ground Cutting inserts. Three kinds of Cutting inserts were manufactured without using grinding process. Machining experiments were carried out to compare the machining performance of non-ground inserts with that of ground ones. The experimental results indicate that the cutting forces and tool wear and surface roughnesses of machined surface of both ground and non-ground inserts are comparable.

• 한국공작기계학회논문집
• /
• 제10권6호
• /
• pp.78-84
• /
• 2001

In the present study, SiCSi-$Si_3 N_4$-SiC ceramic composites that contained up to 30 wt% of dispersed SiC particles were fabricat-ed cia hot-pressing with an oxynitride glass. The microstructure, the mechanical properties and the cutting performance of resulting ceramic composites were investigated. By fixing the composition as $Si_3 N_4$-20wf%SiC, the effect of sintering time on the microstructure, the mechanical properties and the cutting performance were also investigated. The longer sir-tering time is, the bigger the grain size of SiC is. The fracture toughness(-$K_k$) of the $Si_3 N_4$-SiC ceramic composites increased with the increase of gain size, while the flexural strengthh($\sigma$) decreased. For machining SCM440, the insert with 20wt%r SiC sintered for 8 hours showed the longest tool life while the insert with 20wt% SiC sintered for 12 hours showed the longest tool life for machining gray cast iron.