• Journal of the Korean Society of Safety
• /
• v.13 no.1
• /
• pp.19-25
• /
• 1998

In this study, proper injection molding condition has been studied through stress relaxation tests in order to experimentally investigate the effect of the condition on softening of mold product, using specimens produced under the different conditions according to the recommendation of resin manufactures. As a result, softening of the specimens was found to be strongly influenced by material melting temperature. The specimen with higher material melting temperature is found to have lower softening. However, softening of the specimen with lower mold temperature has an decrement, compared with other specimens. In particular, specimen with notch is influenced by mold temperature. The softening increase with higher injection speed and pressure. Finally in order to improve softening, material melting temperature, injection speed and injection pressure were found to be increased with low mold temperature.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.6 s.237
• /
• pp.828-834
• /
• 2005

Recently, injection molded plastic optical products are widely used in many fields, because injection molding process has advantages of low cost and high productivity. However, there remains residual birefringence and residual stresses originated from flow history and differential cooling. The present study focused on developing a technique to measure the birefringence in optical plastic parts using R-G-B separation of white light. The main idea of an analysis comes from the fact that more information can be obtained from the distribution of retardation caused by different wavelengths. A complete system to give the quantitative values of retardation covering high order 2-D birefringence will be demonstrated. Further investigation is under way to improve the accuracy of the system using diodes as light sources.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.4
• /
• pp.17-23
• /
• 2008

Development of die technology for holder and barrel dies is necessary according to minimization of lens assembly, image sensor, and connectors. In these cases, there are two technical problems arising from die design. One is determination of knock-out pin location in die set. Minimization of lens assembly size make it difficult to obtain ejecting space. The other is whether or not high-precision die technology is possible to reduce torque variation when holer and barrel products is assembled. In this study, multi-cavity die set was developed taking advantage of gear-driven ejecting method. In the developed technology, die manufacturing technology was guaranteed with a high-precision level.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.10a
• /
• pp.92-97
• /
• 2004

The aim of this study is to estimate the strength of injection molded plastic stepped gear. We considered stepped gear as plate model which are fixed by two edges. While, on the other sides are free. Normal gear is calculated by Lewis formula which can be derived quite simply from the equation for the stress at the root of a cantilever beam. Stress ratio(step factor) is represented for the ratio of the bending stress of normal and the bending stress of stepped gear, and it is plotted by face width factor. This study is propose the step factor added in Dupont equation which are strength estimation of step gear

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.471-472
• /
• 2006

High aspect ratio of nano hairs on a plastic substrate is molded using thermoplstic materials including COC, PP, PC and PMMA. As a template for molding nano hairs, AAO membrane is adopted, which is 60um thick and 13mm in diameter. This membrane has about 109 of through-holes of which diameter is around 200nm. This AAO membrane and the pellet of materials are stacked in the mold and pressed to mold after heating up to be melted. The AAO membrane is removed using KOH to obtain the molded nano hairs. As a result, the diameter of the molded hairs is around 200nm and the length is $2um{\sim}60um$ depending on the molding conditions and materials.

• 한국금형공학회:학술대회논문집
• /
• 2008.06a
• /
• pp.129-133
• /
• 2008

As a rotating machine element, plastic gears are more and more widely used in such as industrial machine element, since plastic gear is lighter, higher wear-resistance, and higher vibration absorbing ability than metal gears. When operating plastic parts, tooth breakage and fatigue life shortened due to increasing number of applying load and tooth flank temperature rising, such that accuracy of plastic gears is divided from allowable range to cause vibration and noise. On this study, a internal plastic gears are developed which improved the filling balance molding process by a new injection mold structure. The new mold structure called HR3P(hot runner type 3plate mold). As the result from this studies, we obtained a very accurate roundness internal gears by using design of experiment.

• Design & Manufacturing
• /
• v.2 no.2
• /
• pp.33-37
• /
• 2008

This paper describes the optimization of injection molding conditions to minimize sink marks. Sink marks, which refer to a small depression on the surface opposite a thick wall thickness, are often encounted in injection molded plastic parts. Part geometry, material properties and processing conditions during injection molding can affect the sink mark depth. We designed the runner system which is possible balanced filling to cavities using CAE program and then obtained optimal processing conditions by Taguchi's Robust Design technique. By actual injection molding using optimized mold and molding conditions, it confirmed that sink mark depth decreased zero compared to 1mm level in the conventional mold and process.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2006.06a
• /
• pp.47-51
• /
• 2006

레이저를 이용한 폴리머의 융착기술은, 자동차산업에서의 다양한 적용분야에 힘입어 새로운 접합기술로 각광을 받고 있다. 현재까지는, 대부분 작고 간단한 형상의 제품을 융착하는 분야에 많이 적용되어 왔으며, 튼 사이즈의 제품을 대량으로 생산하는 공정에서는 레이저융착이 가지는 다양한 장점에도 불구하고, 프로세스의 안정성, 사출후의 제품변형에 따른 갭의 관리, 작업속도등에 대한 이유로 본격적인 적용을 기피하고 있는 실정이다. 이러한 배경에 의하여 개발된 하이브리드방식(레이저빔+할로겐램프)의 폴리머융착 시스템은, 다이오드레이저에서 출력되는 $800{\sim}980nm$의 레이저파장과 할로겐 램프에서 방사되는 적외선영역의 파장을 동시에 사용함으로써 프로세스의 안장성과 융착효율을 향상시켰다.

• Proceedings of the Safety Management and Science Conference
• /
• 2010.04a
• /
• pp.189-197
• /
• 2010

Recently, industrial business environments have rapidly changed and face severe competitive challenges. The effective inventory system enables to product and deliver the products quickly for meeting due date of customer's order in this environment. This study have developed a web-based inventory system framework using RFID for a plastic injection molding industry. The system analysis inventory problem issues such as inventory planning, warehouse assignment. In this study, web-based inventory system using Java language is proposed and implemented. As the result of implementation of the system, we expected that it manages to inventory planning continually and systematically.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.7
• /
• pp.111-115
• /
• 2008

This paper describes the optimization of injection molding conditions to minimize sink marks. Sink marks, which refer to a small depression on the surface opposite a thick wall thickness, are often encounted in injection molded plastic parts. Part geometry, material properties and processing conditions during injection molding can affect the sink mark depth. We designed the runner system which is possible balanced filling to cavities using CAE program $Moldflow^{TM}$ and then obtained optimal processing conditions by Taguchi's Robust Design technique. By actual injection molding using optimized mold and molding conditions, it confirmed that sink mark depth decreased zero compared to 1mm level in the conventional mold and process.