• Polymer(Korea)
• /
• v.32 no.1
• /
• pp.38-42
• /
• 2008

Ultrathin films were coated on low density Polyethylene (LDPE) food packaging films by plasma polymerization of methane, acetylene, hexamethyldisiloxane (HMDSO), and HMDSO+oxygen to improve the barrier property of the LDPE films. The film coated in HMDSO +oxygen (flow rate: 0.6+ 9.0 SCCM) plasma at 40 W for 10 min showed the highest improvement in the barrier property against oxygen, reducing the permeability of oxygen as much as 18.6 times. The film coated in acetylene (flow rate 0.75 SCCM) plasma at 10 W for 10 min showed the highest improvement in the barrier property against carbon dioxide and moisture, reducing the permeability of carbon dioxide and moisture as much as 12.0 and 3.0 times, respectively. In addition, cherry tomato, cucumber, and mushroom (Flammulina velutipes) wrapped with the coated films were kept fresh $1.5{\sim}3.0$ times longer than those wrapped with an LDPE film.

• Elastomers and Composites
• /
• v.34 no.4
• /
• pp.315-320
• /
• 1999

Surface modification of silicone rubber by low temperature plasma process was investigated to improve quality of silicone EVD tube by reducing tackiness and hydrophobicity. Treatment with nonpolymer-forming plasmas and thin film deposition with polymer-forming plasmas were tried. Tackiness could significantly be reduced, especially by thin film deposition. As a result, the tube became slippery and less vulnerable to contamination in laboratory environment. Inner as well as outer surface of the tube could be changed to be hydrophilic if the plasma contained oxygen. As a result, initial hydrodynamic resistance was reduced. The surface modification did not give any bad influence on mechanical properties of the silicone tube in most cases. Rather, some properties such as Young's modulus, ultimate tensile strength and elongation at break were improved.

• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.710-714
• /
• 2011

In present work, $La_{0.8}Ca_{0.2}CrO_{3}$(LCC), $La_{0.8}Sr_{0.2}CrO_{3}$(LSC) and $La_{0.8}Ca_{0.2}CrO_{0.9}Co_{0.1}O_{3}$(LCCC) ceramic interconnect layer for SOFC were prepared by using thermal plasma spray coating process. The LCC, LSC and LCCC powders were characterized by x-ray diffraction(XRD), scanning electron microscopy(SEM), particle counter and BET analysis. In addition, basic and essential properties such as the surface morphology, cross section, gas leak rate, and electrical conductivity of LCC, LSC, and LCCC layers coated by thermal plasma spray coating process were analyzed and discussed. Based on these experimental results, it can be concluded that the LCCC layer coated by thermal plasma spray coating process can be suitable as a ceramic interconnect of SOFC.

• Journal of Ocean Engineering and Technology
• /
• v.12 no.3 s.29
• /
• pp.49-59
• /
• 1998

The damage mechanism of $Cr_2O_3$ plasma coated soda-lime glass and uncoated glass by steel ball particle impact was analyzed in this study. And the shape variation of the cracks was investigated by stereo-microscope according to the impact velocity and steel ball diameter. In order to improve the damage reduction effect by $Cr_2O_3$ coating layer, crack size was measured and surface erosion state was observed for both of two kinds of specimen after impact experiment. And the results were compared with each other. The 4-point bending test was performed according to ASTM D790 testing method to evaluate the effect of coating layer for bending strength variation. As a result, it was found that the crack size of $Cr_2O_3$ coated specimen was smaller than that of uncoated one, because of the impact absorption by interior pores in the coating layer and the load dispersion by the structural characteristic of the coating layer. For the specimens subjected to the steel ball impact, the bending strength of coated specimen was higher than that of uncoated specimen.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.187-190
• /
• 2009

$LaCrO_3$ series are the most common candidate materials for a ceramic interconnect for SOFC and the thermal expansion coefficient of these matches very well with that of YSZ electrolyte. In this study, characteristics of the coated films on the anode-support, which were formed by using $La_{0.8}Ca_{0.2}CrO_3$, $La_{0.8}Sr_{0.2}CrO_3$, $La_{0.8}Ca_{0.2}Co_{0.1}Cr_{0.9}O_3$ for ceramic interconnet for SOFC, were investigated. All powders showed single perovskite phase and the precursors had spherical shapes of $2{\mu}m{\sim}30{\mu}m$. According to SEM analysis, coated film of LCC on pretreated anode-support was more thicker, whereas the coated film on untreated anode-support was densely formed. As the results of electrical conductivity of anode-support coated with the ceramic interconnects, LCCC exhibited the most excellent electrical conductivity of 0.15S/cm at $750^{\circ}C$.

• Membrane Journal
• /
• v.15 no.3
• /
• pp.233-240
• /
• 2005

Surface modification of polypropylene hollow fiber membranes was performed in order to develop blood-compatibility biomaterials for use in the blood contacting surfaces and oxygenation membranes of a lung assist device (LAD), important medical device even more useful. Blood compatibility of materials was determined by using anticoagulation blood and evaluating formation of blood clots on their surfaces as well as activation of plasma coagulation cascade, platelet adhesion, and aggregation. It was verified that the number of platelets on the silicone coated fibers was significantly lower than that on untreated fiber membrane, indicating improved blood compatibility. It was also found that the polypropylene hollow fiber membranes using plasma treatment exhibited suppression of complement activation in blood compatibility test.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.783-791
• /
• 2000

Increasing demands in productivity are propelling the development of new manufacturing methods like hard machining, high speed cutting (HSC) or machining of difficult to machine materials. In these processes the toois are subjected to very severe mechanical, tribological and thermal loads. They fail prematurely by abrasion, cratering, edge breakage and cold welding. The performance of such tools will be enhanced by better and more wear resistant coatings. The development of these new coatings shows a clear trend towards complex multi-component and multi-layer configurations. TiAIN multilayer coating belongs to these coatings for the new cutting tool generation. This paper tries to explain the benefits of the new coatings. TiAIN multilayer coating offers the following advantages: reduction of manufacturing costs. boost productivity, and lower coolant procurement, conditioning and disposal costs.

• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.3
• /
• pp.201-206
• /
• 2010

In present work, $La_{0.8}Ca_{0.2}CrO_3$ (LCC) ceramic interconnect layer for SOFC was prepared by using thermal plasma spray coating process. The LCC powders were synthesized by Pechini method and calcined at the temperature of $1000^{\circ}C$. The prepared LCC powder was characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), particle counter, BET analysis, respectively. In addition, basic and essential properties of LCC layer coated by thermal plasma spray coating process such as the morphology of surface and cross section for coated layer, gas leak rate, and electrical conductivity were analyzed and discussed. Based on these experimental results, it can be concluded that the LCC layer coated by thermal plasma spray coating process can be suitable as a ceramic interconnect of SOFC operated at $800^{\circ}C$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.4 no.4
• /
• pp.361-365
• /
• 2003

A unipolar-type E-chuck was fabricated for the application of holding silicon wafers in the oxide etcher. For the fabrication of the unipolar ESC, core technologies such as coating of polyimide films and anodizing treatment of aluminum surface were developed. The polyimide films were prepared on thin coated copper substrates to minimize the plasma damage during the etch processing. Thin film heater technology was also developed for new type of E-chuck.

• Journal of Korean Ophthalmic Optics Society
• /
• v.6 no.1
• /
• pp.87-91
• /
• 2001

The a-C:H films have been grown on the glass substrate by PECVD method, where plasma was generated with a 60 Hz line power source. The carbonization is checked from peak intensities of D($sp^3$) and G($sp^2$) peaks in Raman spectra and is analyzed using the Gaussian convolution method of spectrum. Both the bonding strength of C-H and the ratio of $sp^3$ to $sp^2$ in bonding are found to be slightly dependent of partial pressure of $C_2H_2$.