• 한국항공우주학회지
• /
• 제45권1호
• /
• pp.10-20
• /
• 2017

본 연구는 기존 Flow Angularity 장착물 분리 풍동시험 기법을 전산유체해석(Computational Fluid Dynamics)에 적용하여 해석 결과로부터 유동각 데이터베이스를 구성하고 6자유도 분리 궤적 해석한 결과를 전산유체해석의 CTS(Captive Trajectory Simulation) 해석 결과와 비교하여 CFD 해석 기법의 적용 가능성을 확인 한 것이다. Flow Angularity 기법의 전산유체해석 결과는 항공기와 외장간의 각 위치들에서 획득된 공력계수 데이터와 비교하여 데이터의 적절성을 확인하였다. 또한 Flow Angularity 기법으로 획득된 전산유체해석 데이터로부터 획득된 6자유도 외장 분리 궤적과 전산유체해석으로 해석한 CTS 외장분리 궤적을 비교하여 해석 기법의 적용 가능성을 확인하였다.

• 한국군사과학기술학회지
• /
• 제19권4호
• /
• pp.476-482
• /
• 2016

In this study, a method using single Wheatstone bridge flexure has been presented to measure hinge moment acting on control surfaces of wind tunnel models. The structural simplicity of the flexure reduces difficulty regarding gauging and wire-routing, and also makes it feasible to install flexures even inside thin wings. Some flexures were designed and fabricated under typical aerodynamic loads in wind tunnel test, and the strains on the flexure according to applied loads were compared with the result of the analysis by finite element method. The relation between applied loads and output signals showed good linearity, and the standard deviation on the residual errors from linear equation obtained by least square method was within 1.0 % of the maximum design moments. In addition, the FEM analysis on the thickness of load-connecting part of the flexure showed that the sensitivity was improved as the thickness became thin as much as desired to avoid buckling.

• 한국전산유체공학회지
• /
• 제17권1호
• /
• pp.54-60
• /
• 2012

Transition prediction results are validated with experimental data obtained from a transonic wind tunnel for the KU109C airfoil. A Reynolds-Averaged Navier-Stokes code is simultaneously coupled with the transition transport model of Langtry and Menter and applied to the numerical prediction of aerodynamic performance of the KU109C airfoil. Drag coefficients from the experiment are better correlated to the numerical prediction results using a transition transport model rather than the fully turbulent simulation results. Maximum lift coefficient and drag divergence at the zero-lift condition with Mach number are investigated. Through the present validation procedure, the accuracy and usefulness of both the experiment and the numerical prediction are assessed.

• 대한기계학회논문집
• /
• 제12권4호
• /
• pp.892-899
• /
• 1988

본 연구에서는 특정한 콘테이너 크레인을 설계도면에 따라 100:1 축척의 모형 을 제작하고 Reynolds 수에 의한 축척영향, 모형취부 및 계측 시스템의 반복성 영향, 풍향에 따른 특성, boom의 위치에 따른 특성, 풍고도에 따른 특성, blockage 영향, 설 계변경에 따른 효과에 주 관심을 두고 연구하였다. 특히 설계단계에서 관련 규격에 따라 예측된 풍하중이 실제와 어느 정도로 일치하는지에 관심을 두고 풍동시험 결과와 비교했다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.431-434
• /
• 2009

Conceptual study of an open-circuit type low-speed wind tunnel for test of wind turbine blade is conducted. The tunnel is constituted of a settling chamber, a contraction, closed and open test sections, a diffuser, two corners, a cross leg and a fan and motor. For the performance test, the closed test section width of 1.8 m, height of 1.8 m and length of 5.25 m is selected. The open test section with dimension width of 1.8 m, height of 1.8 m and length of 4.14 m is adopted for aeroacoustic test. The contraction ratio is 9 to 1 and maximum speed in the closed test section is 67 m/sec. Input power in the tunnel is about 238 kW and its energy ratio is 3.6. The wind tunnel designed in present study will be an effective tool in research and development of wind turbine.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.33.2-33.2
• /
• 2011

The 'NREL Phase VI' model with a 10.06m diameter was tested in the NASA Ames tunnel to make a reference data of the computational models. The test was conducted at the one rotational speed, blade tip speed 38m/s and the Reynolds number of the sectional airfoils in that test was around 1E6. The 1/5 scale down model of the 'NREL Phase VI' model was used in this paper to study the power characteristics in low Reynolds number region, 0.1E6 ~ 0.4E6 which is achievable range for the conventional wind tunnel facilities. The torque generated by the blade was directly measured by using the torque sensor installed in the rotating axis for a given wind speed and rotational speed. The power characteristics below the stall condition, lambda > 4, was presented in this paper. The power coefficient is very low in the condition below the Re. 0.2E6 and rapidly increases as the Re. increases. And it still increases but the variation is not so big in the condition above the Re. 0.3E6. This results shows that to study the performance of the wind turbine blade by using the scaled down model, the Re. should be larger than the 0.3E6.

• 한국군사과학기술학회지
• /
• 제22권5호
• /
• pp.637-643
• /
• 2019

Wind tunnel testing for flow-through model is necessary for performance prediction of an aircraft with air-breathing jet engine. Internal drag correction and wall correction are performed to acquire preciser wind tunnel test data. Many test runs are generally required to correct internal drag and wall interference in wind tunnel test. In this study we investigated more effective correction schemes using the response surface method. Even though the number of tests required for these schemes was much smaller than that for conventional methods, the differences between corrections using these schemes and conventional methods were similar level with the uncertainty of measurement except for the data near the boundaries.

• 풍력에너지저널
• /
• 제15권1호
• /
• pp.11-20
• /
• 2024

As the generation capacity of floating offshore wind turbines increases, the wind load applied to each turbine increases. Due to such a high wind load, the capacity of transport equipment (such as tugboats or cranes) required in the transportation and installation phases must be much larger than that of previous small-capacity wind power generation systems. However, for such an important wind load prediction method, the simple formula proposed by the classification society is generally used, and prediction through wind tunnel tests or Computational Fluid Dynamics (CFD) is rarely used, especially for a concept or initial design stages. In this study, the wind load of a 10 MW class floating offshore wind turbine was predicted by a simplified formula and compared with results of wind tunnel tests. In addition, the wind load coefficients at each stage of fabrication, transportation, and installation are presented so that it can be used during a concept or initial design stages for similar floating offshore wind turbines.

• 한국항공우주학회지
• /
• 제39권5호
• /
• pp.385-390
• /
• 2011

본 연구의 목적은 풍동시험을 통해 회전발사체에서 발생하는 동적 마그너스 효과를 실험적으로 측정하는데 있었으며, 이를 위해 약 12,000 rpm으로 회전하는 155-mm 회전발사체 실험모형에 작용하는 마그너스 특성의 측정을 위한 고속풍동실험을 국방과학연구소 삼중음속풍동에서 수행하였다. 실험시의 마하수는 0.7~2.0까지였으며 이때의 받음각 구간은 -4~+10 deg이었다. 풍동실험 측정기법의 유효성 평가를 위해 동일형상 모형에 대해 기 수행하였던 마그너스 측정결과와의 비교검토를 수행하였으며, 기존 연구결과들과 잘 부합됨을 확인하였다.

• 한국전산유체공학회지
• /
• 제10권2호
• /
• pp.60-68
• /
• 2005

For study on the unsteady wall interference effect, flows around a forced oscillating airfoil in closed test-section wind tunnels have been numerically investigated by solving compressible Navier-Stokes equations. The numerical scheme is based on a node-based finite-volume method with the Roe's flux-difference splitting and an implicit time-integration method coupled with dual time-step sub-iteration. The Spalart-Allmaras one-equation model is employed for the turbulence effect. The computed results of the oscillating airfoil having a thin wake showed that the lift curve slope is increased and the magnitude of hysteresis loop is reduced by the interference effects. Since the vortex around the airfoil is generated and convected downstream faster than the free-air condition, the phase of lift, drag and pitching moment coefficients was shifted. The pressure on the test section wall shows harmonic terms having the oscillating frequency contained in the wail effect.