• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2007.12a
• /
• pp.357-359
• /
• 2007

해양에너지원 중에서 파랑은 모든 해역에 폭넓게 분포하므로 가용에너지원이 풍부하고 에너지를 회수하기 위한 장치를 설치할 수 있는 해역 또한 광범위하며 반도의 지형을 지닌 우리나라의 연안 해역에 대규모로 활용이 가능한 에너지 자원중 하나이다. 본 연구는 새로운 방식인 파력발전용 횡류형터빈인 케이슨 내장형 횡류터빈을 개발하기에 앞서 파랑수조의 왕복운동을 CFD해석을 통하여 구현하는 것이다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.10
• /
• pp.1202-1209
• /
• 2004

In this study, numerical investigation has been performed on the evolution of weld pool geometry with moving free surface during low-energy density laser welding process. The free surface elevates near the weld pool edge and descends at the center of the weld pool if d$\sigma$/dT is dominantly negative. It is shown that the predicted weld pool width and depth with moving free surface are a little greater than those with flat weld pool surface. It is also believed that the weld pool surface oscillation during the melting process augments convective heat transfer rate in the weld pool. The present analysis with moving free surface should be considered when We number is very small compared to 1.0 since the deformation of the weld pool surface is noticeable as We number decreases.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.133-138
• /
• 2003

In this study, numerical investigation has been performed on the evolution of weld pool geometry with moving free surface during low-energy density laser welding process. The free surface elevates near the weld pool edge if ${\partial}{\sigma}/dT$ is dominantly negative. On the contrary, the free surface rise at the center of weld pool in case of mainly positive ${\partial}{\sigma}/dT$. The predicted weld pool width and depth with moving free surface are 5∼15%$5{\sim}15%$ greater than those with flat weld pool surface. It is considered that weld pool surface oscillation during melting process augments convective heat transfer rate in the weld pool.

• Proceedings of the Optical Society of Korea Conference
• /
• 2002.07a
• /
• pp.244-245
• /
• 2002

1 picosecond 보다 짧은 펄스길이를 갖는 초단파길이 레이저 펄스 (Ultrashort laser pulse, USLP)를 이용한 물질의 절제 (ablation)는 여타 nanosecond 영역의 레이저 절제와 많은 차이를 보인다(1). USLP는 순간 파워가 매우 높기 때문에 직접적으로 물질의 원자를 분리시켜 자유전자를 형성한다 이들 자유전자는 일반 선형흡수체 (linear absorbing chromophore)보다 흡수계수가 몇 십 배로 높아 대부분의 펄스 에너지가 표면 100-200 m 이내의 극히 작은 지역에 밀집되게 된다. (중략)

• Clean Technology
• /
• v.5 no.2
• /
• pp.37-44
• /
• 1999

The influence of the reactant composition on the surface free energy and on the dispersity in water was investigated by using the fluorine-containing water-soluble polyurethane synthesized with the fluorine-containing diol and hydrophilic diol. The diol donating ionic characteristics was more effective than polyol, and stable emulsion with the diameter of 610~310 nm was obtained in the range of 0.3~0.7 molar ratio of the diol to polyol. According to the increment of fluorine-containing compound up to 10 wt %, the surface free energy of polyurethane was dramatically decreased from 22.3 to 12.6 dyn/cm, and the diameter of water dispersed polyurethane increased from 380 to 860 nm due to the strong interaction between polymer molecules because fluorine segments are arranged on the surface of molecules. The macromonomer with perfluoroalkyl group was more effective in complement of the weak point of water-soluble polyurethane, which is a decrease of hydrophobicity, because of strong hydrophobicity.

• Elastomers and Composites
• /
• v.37 no.4
• /
• pp.258-264
• /
• 2002

In this work, the influence of thermal treatment on surface properties of silicas and mechanical interfacial properties of silicas/polyurethane composites was investigated. The surface properties of thermally treated silicas were studied in the context of Fourier Transform-IR (FT-IR), solid-state 29Si NMR spectroscopy, and contact angle. And the mechanical interfacial properties of the silica/polyurethane composites were evaluated by composite tearing energy (GIIIC). As a result, it was found that the thermally treated silica surfaces became hydrophobic in nature, due to the condensation of surface hydroxyls and the formation of siloxane bonds, resulting in increasing the London dispersive component of surface free energy. From which, the increase of the London dispersive component of the silicas led to an improvement of the dispersion of silicas in a polyurethane matrix, finally resulting in improving the tearing energy (GIIIC) of the silicas/polyurethane composites.

• Polymer(Korea)
• /
• v.29 no.6
• /
• pp.581-587
• /
• 2005

Commercial polyurethane film (PU) was modified with Ar plasma ionized in dielectric barrier discharge (DBD) plate-type reactor under atmospheric pressure. We measured the change of the contact angle and the surface fee energy with respect to the plasma treatment conditions such as treatment time, RF-power, and Ar gas flow rate. We also optimized the plasma treatment conditions to maximize the surface peroxide concentration. At the plasma treatment time of 70 sec, the power of 120 W and the Ar gas flow rate of 5 liter per minute (LPM), the best wettability and the highest surface fee energy were obtained. The 1,1 diphenyl-2-picrylhydrazyl (DPPH) method confirmed that the surface peroxide concentration was about 2.1 nmol/$\cm^{2}$ at 80 W, 30 sec, 6 LPM.

• Polymer(Korea)
• /
• v.26 no.4
• /
• pp.445-451
• /
• 2002

In this work, the adsorption characteristics and mechanical interfacial properties of treated silicas by silane coupling agents, such as, ${\gamma}$-methacryloxy propyl trimethoxy silane (MPS), ${\gamma}$-glycidoxy propyl trimethoxy silane (GPS), and ${\gamma}$-mercapto propyl trimethoxy silane (MCPS), were investigated. The equilibrium spreading pressure ($pi_e$), surface free energy ($gamma_s$ s/), and specific surface area ($S_{BET}$) were studied by the BET method with $N_2$/77 K adsorption. The developments of nonpolar functional groups of the silica surfaces treated by silane coupling agents led to the increase in the $S_{BET}$, $pi_e$, and $gamma_s$, resulting in the improved tearing energy ($G_{mc}$)of the silica/rubber composites. The composites treated by MPS showed the superior mechanical interfacial properties in these systems. These results explained by changing of crystalline size, dispersion, agglomerate, and surface functional group of silica/rubber composites.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.329-333
• /
• 2005

Total temperature distribution in high speed fee & wall jet regions was investigated using the total temperature probe. For the free jet, the distance of probe from the nozzle exit is changed in the range of 1, 2, 4 and 6 times o nozzle exit diameter. Energy separation phenomenon was observed on shear layer between jet and ambient. In wall jet region, impinging plate was fixed at Z/D=2 and total temperature distribution has been measured for various radial distance($R/D=1.25\sim2.0$). Energy separation phenomenon was found at wall jet boundary and near wall, and was compared with measured adiabatic wall temperature value.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.15 no.4
• /
• pp.273-280
• /
• 2012

The numerical simulation using the Lattice Boltzmann Method in the field of computational fluid dynamics becomes wider in the engineering applications because of its simplicity of update rules compared to the conventional Navier-Stokes solvers. Here, a two-dimensional D2Q9 LB model is numerically tested with a few new computational treatment on the free surface. The single relaxation time is applied under the gravitational field where applied only in the higher density fluid because of its big density difference. At the free surface, the reconstruction techniques in combination with boundary conditions is adopted in order to get some distribution function coming into the fluid site from the air one, and surface tension, early stable test for the gravitional field is considered in it. With the implementation of the gravitational profile, conserving the overall mass and grid dependency are observed during the calculations and freesurface advance track is well captured with an experiment.