• Geotechnical Engineering
• /
• v.11 no.4
• /
• pp.99-110
• /
• 1995

In this study, friction angles on the surface of vertical rigid ground anchor in normally consolidated dry sand were measured by model pullout tests in laboratory. Friction angles were obtained from the normal and shear stresses measured along depth of the anchor stir face by attaching several 2-dimensional load cells. Model tests were conducted under the plane strain state and axial symmetric state. From the results of tests, it was concluded that the maximum friction angle on the anchor surface coincides nearly with the maximum angle of stress obliquity on the plane of zero-extension direction obtained by plane strain compression test. This result was made with regard to the strength anisotropy and stress dependency of sand. It showed that when angle of shear resistance of the sand is applied to the friction angle of the anchor surface, the design capacity could be less than the applied force, thus making the anchor unsafe.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.4
• /
• pp.1281-1293
• /
• 2013

A sophisticated finite element model is illustrated to analyze the behavior of Prefabricated Parallel Wire Strand(PPWS) sockets for main cables of suspension bridges. An orthotropic model is proposed for the casting material by considering both effects of individual wires and a casting alloy, and the contact between surfaces of a socket and a casting alloy is idealized by using the Coulomb friction and the surface-based contact model. The proposed FE model is verified by comparing the strain distributions obtained from the tensile test and FE analysis. The mechanical behavior of a socket is investigated with respect to the variation of the frictional coefficient. The result shows that the friction between surfaces significantly diminishes the stress concentration of a socket and a casting alloy, and the normal stress from the design equation represents the averaged value of the upper and lower quartiles in the distribution of contact stresses between a socket and a casting alloy.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.10
• /
• pp.1479-1485
• /
• 2010

In recent times, due to wire drawing of high carbon steel at a high speed to ensure a high productivity and high strength, axial residual stress are generated because of rapid increase in surface temperature. In the process, the temperatures of the wires increased because of the deformation of the wires and the friction between the die and wire. In particular, in the case of the wire drawing at a high speed, friction leads to a large temperature gradient so that considerable axial residual stress is generated on the surface. In this study, the relationship between axial residual stress and increase in the surface temperature was investigated, and a prediction model of uniform temperature was proposed. Then, a prediction model for residual stress was developed. The proposed model was verified by measuring the residual stress by X-ray diffraction on drawn wires.

• Geotechnical Engineering
• /
• v.10 no.4
• /
• pp.39-52
• /
• 1994

The group effect of inclined ground anchor should be considered in design, but it has been hardly studied due to the difficulties of experimental or theoretical study. In this study, the model tests for the inclined ground anchors are made, and the displacements and strain fields of ground around anchor surface are analysed. As the results of this study, the group effect of the inclined ground anchor in air dried sand ground does not show even though two anchor surfaces are very close(10.7cm, surface to surface). That is to say, ,in the case that the final failure surface by pullout of anchor shows on the anchor surface, the pullout resistances of single anchors are almost same as those of the group anchors in these model tests.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.1
• /
• pp.116-122
• /
• 1988

Interfacial shear stresses have been determined for countercurrent stratified flow of air and water in a nearly-horizontal rectangular channel, based upon measurements of pressure drop, gas velocity profiles and mean film thickness. A dimensionless correlation for the interfacial friction factor has been developed as a function of the gas and liquid Reynolds numbers. Equivalent surface roughnesses for the interfacial friction factor have been calculated using the Nikuradse correlation and have been compared with the intensity of the wave height fluctuation on the interface. The results show that the interfacial shear stress is mainly affected by turbulent mixing near the interface due to the wave motion rather than by the roughened surface.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.2
• /
• pp.87-94
• /
• 2006

An experimental research program providing knowledge to measure two-dimensional skin friction variation over a certain region of model surface is presented. In the oil-fringe imaging skin friction(FISF) technique, local slope of a thin oil applied on a test surface is measured from the interference fringe patterns on the oil surface, and its information is then related to the applied shear over the oil by the thin-oil lubrication theory. The FISF technique has been applied for a separation flowfield ahead of a circular cylinder vertically mounted on a flat plate, and it has been found that the FISF skin friction results show good comparison with the other numerical/experimental data obtained for similar conditions. implying an applicability of the technique.

• Tribology and Lubricants
• /
• v.8 no.2
• /
• pp.35-43
• /
• 1992

취성재료의 마멸천이기구를 규명하기 위해 반무한탄성체상에 표면균열이 존재할 때 그 위를 헤르쯔 접촉하중이 이동할 경우를 해석모델로 하여 선형파괴역할을 도입하여 해석하였다. 해석방법으로는 표면균열을 인상전위의 연속분포로 치환하여 Erdogan-Gupta의 방법으로 균열끝면의 응력확대계수를 구하여, 취성재료의 균열전파조건인 Erdogan-Sih Criterion을 사용하여 그 전파특성을 해석하였다. 본 논문에서는 마멸율이 적은 마멸에서 마멸율이 큰 마멸로 전이할 때 급격한 표면손상과 마찰계수의 급격한 증가를 동반하므로 이에 대한 해석에 중점을 두었다. 해석결과는 접촉하중과 마찰계수의 증가는 표면균열의 전파를 야기시켜 대규모 마멸입자를 생성시키게 됨을 보여주었다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.143-143
• /
• 2017

CrAlN 코팅은 높은 경도, 낮은 표면 조도 등의 상온에서의 우수한 기계적 특성 이외에 고온에서 안정한 합금상의 형성으로 인하여 우수한 내산화성 및 내열성을 보유하여 공구 코팅으로의 적용 가능성이 크다. 그러나 최근 공구사용 환경의 가혹화로 인하여 코팅의 내마모성 및 내열성 등의 물성 향상을 통한 공구의 수명 향상이 필요시 되고 있으며, 다양한 코팅 물질을 활용하여 다층 코팅을 합성함으로써 난삭재용 공구 코팅의 물성을 높이는 연구들이 진행되고 있다. 본 연구에서는 CrAlN 코팅과 WC-Co 6wt.% 모재 사이에 CrZrN, CrN, CrN/CrZrSiN 등의 중간층을 합성하여 CrAlN 코팅의 상온 및 고온 특성을 향상시키는 연구가 진행되었다. 합성된 코팅의 구조 및 물성을 분석하기 위해 field emission scanning electron microscopy(FE-SEM), nano-indentation, atomic force microscopy(AFM) 및 ball-on-disk wear tester를 사용하였다. 코팅의 고온 특성을 확인하기 위해 코팅을 furnace에 넣어 공기중에서 30분 동안 annealing 한 후에 nano-indentation을 사용하여 경도를 측정하였고, $500^{\circ}C$ annealing 코팅의 표면 조도 분석 및 $500^{\circ}C$에서 마찰마모시험을 실시하였다. CrAlN 코팅의 상온 특성을 분석한 결과, 모든 코팅의 경도(35.5-36.2 GPa)와 탄성계수(424.3-429.2 GPa)는 중간층의 종류에 상관없이 비슷한 값을 보인 것으로 확인됐다. 그러나, CrN/CrZrSiN 중간층을 증착한 CrAlN 코팅의 마찰계수는 0.33로 CrZrN 중간층을 증착한 CrAlN 코팅의 마찰계수(0.41)에 비해 향상된 값 보였으며, 코팅의 마모율 및 마모폭도 비슷한 경향을 보인 것으로 보아 코팅의 내마모성이 향상된 것으로 판단된다. 이것은 중간층의 H/E ratio가 코팅의 내마모성에 미치는 영향에 의한 결과로 사료된다. H/E ratio는 파단시의 최대 탄성 변형율로써, 모재/중간층/코팅의 H/E ratio 구배에 따라 코팅 내의 응력의 완화 정도가 변하게 된다. WC 모재 (H/E=0.040)와 CrAlN 코팅(H/E=0.089) 사이에서 CrN, CrZrSiN 중간층의 H/E ratio는 각각 0.076, 0.083 으로 모재/중간층/코팅의 H/E ratio 구배가 점차 증가함을 확인 할 수 있었고, 일정 응력이 지속적으로 가해지면서 진행되는 마모시험중에 CrN과 CrZrSiN 중간층이 WC와 CrAlN 코팅 사이에서 코팅 내부의 응력구배를 완화시키는 역할을 함으로써 CrAlN 코팅의 내마모성이 향상된 것으로 판단된다. 내열성 시험 결과, CrN/CrZrSiN 중간층을 증착한 코팅은 $1,000^{\circ}C$까지 약 28GPa의 높은 경도를 유지한 것으로 확인 되었다. $500^{\circ}C$ annealing 후 진행된 표면 조도와 마모시험 결과, 모든 코팅의 조도 값 및 마찰계수는 상온 값에 비해 증가하였으며 CrN/CrZrSiN 중간층을 증착한 CrAlN 코팅의 변화량이 가장 낮은 값을 보였다. 이는 CrZrSiN 중간층 내에 존재하는 $SiN_x$ 비정질상이 고온 annealing시에 산소 차폐막 역할을 하여, 코팅내의 잔류 산소에 의한 산화작용을 효과적으로 방지함으로써 코팅의 고온 특성이 향상된 것으로 판단된다.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.4
• /
• pp.160-166
• /
• 2001

The theoretical analyses for stresses induced in axial direction in the buried pipelines are reviewed. The influences of the axially directed stresses on the surface elliptical crack are studied in detail and thus some engineering technical informations are provided to use reliability assessment of buried pipelines. The change in temperature, the effect of inner pressure and soil friction in the buried pipeline constrained in axial direction are included to determine the axial stresses in the buried pipeline. Furthermore, the stress induced by the pipeline bending are also considered. The stress intensity factors calculated by two models such as a simple plane crack and an elliptical surface crack for a circumferential surface elliptical crack are compared.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.417-420
• /
• 2000

The theoretical analyses for stresses induced in axial direction in the buried pipelines are reviewed. The influences of the axially directed stresses on the surface elliptical crack are studied in detail and thus some engineering technical informations are provided to use reliability assessment of buried pipelines. The change in temperature, the effect of inner pressure and soil friction in the buried pipeline constrained in axial direction are included to determine the axial stresses in the buried pipeline. Furthermore, the stress induced by the pipeline bending are also considered. The stress intensity factors calculated by two models such as a simple plane crack and an elliptical surface crack for a circumferential surface elliptical crack are compared.