• Proceedings of the Korea Water Resources Association Conference
• /
• 2020.06a
• /
• pp.54-54
• /
• 2020

본 연구에서는 제방의 세굴이나 붕괴를 방지하기 위해 바이오폴리머(Biopolymer) 기반 신소재를 활용한 흙 제방의 보강공법을 제시하였다. 바이오폴리머 기반 제방의 보강공법은 흙과 바이오폴리머를 소량만 섞어도 흙의 강도 증진시킴과 동시에 빗물에 대한 내침식성과 식생의 생장을 촉진하는 생태성도 뛰어나기 때문에 제방 사면을 보호할 수 있는 친환경적이고 효율적인 공법이다. 이에 안동하천연구센터는 실증실험을 통한 신소재 제방 보강공법의 안정성 검증을 목표로 2 건의 월류붕괴 실험을 수행하였다. 첫 번째는 흙 제방 조건(Case 1)이며, 두 번째는 바이오폴리머 혼합 토양을 사면에 도포한 후 식생이 활착된 조건(Case 2)이다. 제방 붕괴에 따른 수로 내 수위변화를 측정하기 위해 압력식 수위계를 설치하였으며, 영상분석을 위한 다수의 카메라 및 드론을 활용하여 실험의 전 과정을 실시간 촬영하였다. 또한, 제내지 측 사면을 대상으로 월류에 따른 붕괴 지연효과를 정량적으로 제시하기 위해 이미지 픽셀 변화 측정 기법을 통한 시간에 따른 표면 손실률을 산정하였다. 흙 제방과 신소재 처리 제방의 시간에 따른 표면손실률을 비교한 결과, Case 2의 사면손실률이 Case 1에 비해 약 1.5~2.3 배 지연되는 것을 확인하였다. 하지만 단일 조건만으로 실험군과 비교군의 붕괴지연 결과가 제방 성능을 평가함에 있어서 일반화될 수 없으므로 이러한 정량적 평가는 다소 한계가 있다. 향후 이러한 부족한 부분을 해결하기 위한 노력과 다양한 조건의 추가실험을 통한 계측 데이터 및 붕괴지연시간의 평균값을 도출하여 신소재 제방의 안정성을 평가하기 위한 타당한 결과를 도출할 예정이다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.2
• /
• pp.82-86
• /
• 2011

Lightweight aggregate which is composed of sintered polycrystalline materials usually has a certain portion of pores inside of it. Because of such a structural characteristics, it tends to that movement of water in aggregate shows an abnormal behavior against the change of outside environment. In general, water movement behavior is controlled by porosity, distribution of pore size; however, dense surface layer will also affect water movement behavior in case of artificially sintered aggregates. Factors affecting water movement behavior in the aggregate are pore distribution, pore shape, pre-wetting method, etc. In this study, absorption characteristics of aggregate under the pressure and absorption rate according to water dipping time are analyzed for the basis of pressure pumping of lightweight concrete. Two kinds of aggregates were used for the test: one is made by 'L' company in Germany and the other is of our own made at the pilot plant in Kyonggi University. Absorption rate of aggregate is measured according to water dipping time, vacuum pressure, and quenching condition. Absorption rate of aggregate with $300^{\circ}C$ quenching is higher than that of aggregate with 24 hr water dipping. Generally the more vacuum the higher water absorption rate. Water absorption rate of 'L' aggregate under -300 mmHg is 54 % higher than that of aggregate with 24 hr water dipping; however, only 2 % increase in water absorption was measured for the K622 and K73 which were of our own.

• Journal of Bio-Environment Control
• /
• v.18 no.4
• /
• pp.303-308
• /
• 2009

This study was conducted to analyze the feasibility of plant growth under low pressure and to investigate the effect of pressure on plant growth. Three levels of pressures (25, 50, and 101.3 kPa (control)) were provided to analyze the growth of Lettuce (Lactuca sativa L.) as affected by low pressure. Photoperiod, air temperature, and photosynthetic photon flux were set at 16/8 h, 26/$18^{\circ}C$, and $240{\mu}mol{\cdot}m^{-2}s^{-1}$, respectively. Growth characteristics of lettuce were measured on 7 days and 14 days after experiment. Leaf length, leaf width, leaf area, and root dry weight of lettuce measured on 7 days under 25 and 50 kPa were significant as compared to the control. Leaf length, top dry matter and root dry matter of lettuce measured on 14 days were significantly different under 25 and 50 kPa. From these results, we confirmed that lettuce could be grown under low pressure. However high relative humidity by evapotranspiration from leaves and growing beds under low pressure caused the condensation on the inner surface of the chamber. Therefore in a low pressure chamber, humidity control is required to maintain the relative humidity at a proper level.

• 전자공학회논문지 IE
• /
• v.44 no.2
• /
• pp.8-13
• /
• 2007

This paper aims to analyze the characteristics of ITO which are caused by variation of plasma condition to fabricate the OLED of high efficiency. We treated $N_2$ gas and $O_2$ gas plasma on the surface of the ITO by changing their RF plasma power into 100 W, 200 W, 400 W and by changing their 9as pressure into 12 mTorr, 120 mTorr. The work function of ITO that plasma treatment was done by using $N_2$ gas had value of $4.88{\sim}5.07\;eV$, and that by using $O_2$ gas, $4.85{\sim}4.97 eV$. The characteristics of the ITO were most efficient in the $N_2$ gas plasma with the RF power of 200W and gas pressure of 120 mTorr. The rms roughness of ITO surface is the value from AFM image. In this case, ITO obtained $25.2\;{\AA}$ and $30.5\;{\AA}$ in the $N_2$ and $O_2$ gas plasma respectively when it had the RF power of 200 W. But ITO that didn't have plasma treatment was $44.5{\AA}$. The variation of ITO transmittance was almost not discovered by the change of $N_2$ gas and $O_2$ gas pressure.

• Journal of the Korean Vacuum Society
• /
• v.22 no.3
• /
• pp.111-118
• /
• 2013

The influence of gas flow on the plasma generation in the atmospheric plasma jet is described with the theory of hydrodynamics. The plasma discharge is affected by the gas-flow streams with Reynolds number (Re) as well as the gas pressure with Bernoulli's theorem according to the gas flow rate inserted into the glass tube. The length of plasma column is varied with the flow types such as the laminar flow of Re<2,000 and the turbulent flow of Re>4,000 as it has been known in a general fluid experiments. In the laminar flow, the plasma column length is increased as the increase of flow rate. Since the pressure in the glass tube becomes low as the increase of flow velocity by the Bernoulli's theorem, the breakdown voltage of plasma discharge is reduced by the Paschen's law. Therefore, the plasma length is increased as the increasing flow rate with the fixed operation voltage. In the transition of laminar and turbulent flows, the plasma length is decreased. When the flow becomes turbulent as the flow rate is increasing, the plasma length becomes short and the discharge is shut down ultimately. In the discharge of laminar flow, the diameter of plasma beam exposed on the substrate surface is kept less than the glass diameter, since the gas flow is kept to the distinct distance from the nozzle of glass tube.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.33 no.10
• /
• pp.1726-1734
• /
• 2004

Response surface methodology on sensory evaluation was used to optimize cooking condition of cooked short grain rice (CSR) and cooked short grain rice containing grainy sea-tangle patch (CSTR). Texture profile analysis and nutritional evaluation were also performed. For maximizing overall acceptability, it can be predicted sea-tangle patch 14%, added water 1.67 times of rice and sea-tangle amount and steeping time 47 min as optimum cooking conditions from sensory evaluation conducted by the forties panelist. Hardness of pressure cooked short grain rice containing grainy sea-tangle patch (CSTR) were lower than cooked short grain rice (CSR), but it showed similar as CSR in adhesiveness, chewiness and higher in springiness and cohesiveness. In addition CSTR was delayed retrogradation compared with CSR. The nutritional Quality of CSTR showed higher level in total dietary fiber, protein, ash than CSR, but lower in protein digestibility, C-PER, gelatinization degree compared with CSR.

• The Korean Journal of Rheology
• /
• v.10 no.4
• /
• pp.185-194
• /
• 1998

Flow-induced voids during resin impregnation and poor fiber wetting give serious effects on the mechanical properties of composites in resin transfer molding process. In order to better understand the characteristics of resin flow and to investigate the mechanism of void formation, flow visualization experiment for the resin impregnation was carried out on plain weaving glass fiber mats using silicon oils with various viscosity values. The permeability and the capillary pressure for the fiber mats of different porosities were obtained by measuring the penetration length of the resin with time and with various injection pressure. At low porosity and low operating pressure, the capillary pressure played a significant role in impregnation process. Video-assisted microscopy was used in taking the magnified photograph of the flow front of the resin to investigate the effect of the capillary pressure on the void formation. The results showed that the voids were formed easily when the capillary pressure was relatively high. No voids were detected above the critical capillary number of 2.75$\times$$10^{-3}, and below the critical number the void content increased exponentially with decrease of the capillary number. The content of void formed was independent of the viscosity of the resin. For a given capillary number, the void content reduced with the lower porosity of the fiber mat.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.615-615
• /
• 2013

탄소나노튜브(carbon nanotubes; CNT)는 강철보다 10~100배 견고할 뿐만 아니라 영률과 탄성률 은 각각 1.8 TPa, 1.3 TPa에 달하는 매우 우수한 기계적 강도를 지니고 있으며, 구리보다 좋은 전기 전도도와 다이아몬드의 2배에 이르는 열전도도를 지닌 물질이다. 이러한 탄소나노튜브의 우수한 특성을 이용하여 나노섬유, 고분자-탄소나노튜브의 고기능 복합체, 나노소자, 전계방출원(field emitter), 가스센서 등 다양한 분야로의 활용을 위한 연구가 진행되고 있다. 특히, 수백 ${\mu}m$ 이상의 길이로 수직 성장된 탄소나노튜브(VA-CNTs)의 합성은 길이 대 직경의 비(aspect ratio)가 비약적으로 증가하여 앞서 언급한 분야로의 활용이 더욱 유리하며, 그 중에서도 대량 생산, 나노섬유 및 나노복합체로서의 활용에 극히 유용하다. 최근에는 열 화학기상증착(thermal chemical vapor deposition; TCVD)법을 이용하여 탄소나노튜브의 구조를 제어하는 연구들이 많이 보고되고 있다. 열 화학기상증착을 이용한 수직 정렬된 탄소나노튜브의 합성에서 합성조건의 변화는 탄소나노튜브의 길이, 벽의 수, 직경, 결정성 등 구조에 큰 영향을 미친다. 탄소나노튜브는 이러한 구조에 따 라 물리적 특성이 달라지기 때문에 다양한 분야로의 응용을 위해서는 합성에 대한 근본적인 이해 가 절실히 요구된다. 본 연구에서는 열 화학기상증착법을 이용한 합성에서 성장압력의 변화에 따른 탄소나노튜브의 구조적 특성을 조사하였다. 성장압력의 변화는 탄소나노튜브의 밀도, 길이, 결정성에 큰 영향을 미치는 것을 주사전자현미경과 라만분광법을 이용하여 확인하였다. 이러한 결과 는 탄소나노튜브 박막(CNT forest)의 가장자리(edge)에 비정질 탄소(amorphous carbon)의 흡착으로 인한 나노튜브사이의 간격(intertube distance)이 좁아짐에 따른 가스공급 차단 효과로 설명이 가능 하다. 또한, 마이크로웨이브 플라즈마 화학기상증착법을 이용하여 탄소나노튜브를 합성하였다. 합성과정 중 산소(O2)를 주입 하였을 경우, 그렇지 않은 경우에 비하여 성장 속도가 증가하여 3시간 합성 시 2 mm가 넘는 수직 정렬된 탄소나노튜브를 합성 할 수 있었다. 이러한 결과는 과잉 공급 되어 탄소나노튜브로 합성되지 못하고 촉매금속의 표면과 탄소나노튜브의 벽에 비정질의 형태로 붙어있는 탄소 원자들을 추가 주입해 준 산소에 의하여 CO 또는 CO2 형태로 제거해 줌으로써 활성화된 촉매금속의 반응 시간을 향상 시켜주어 탄소공급이 원활하게 이루어졌기 때문이라 생각된다.

• Applied Biological Chemistry
• /
• v.30 no.1
• /
• pp.65-70
• /
• 1987

In Girder to measure the pressure and weight decrease of drying sample during the vacuum drying process of food, sensing devices were designed and constructed with strain gauge. Microcomputer based vacuum drying system was made up of these devices interfaced to apple II microcomputer. The electrical output signal from vacuum sensor which constituted with Bourdon tube whereon strain gauge attached were digitalized and input to microcomputer through the MC 6821 interface I.C. chip. The relationship between read-out digital value (D) from microcomputer and readings of vacuum gauge (P, mmHg) was P=-146.136+3.620D'(r=0.9994) The pressure control of vacuum dryer was successfully conducted in the range of $400{\sim}600\;mmHg$ accuracy. The digitalized load cell output (D) could be correlated with the real weight (W, g) as W=-14,000+0.585D (r=0.9998) Drying curves of green red pepper under $64^{\circ}C$, $400{\sim}600\;mmHg$ was similar to those of red pepper and differently affected by the degree of vacuum pressure but was varied according to their shape (cut or whole). Moisture movement of green red pepper during the vacuum drying process was fitted to Page model. The empirical equations obtained were $M-M_e/M_o-M_e={\exp}\;(-0.0673{\theta}^{1.177})$ and $M-M_e/M_o-M_e={\exp}\;(-0.0655\;{\theta}^{1.477})$ for whole and cut green red pepper, respectively.

• Journal of Biomedical Engineering Research
• /
• v.24 no.1
• /
• pp.37-44
• /
• 2003

This experimental study is aimed at evaluating the hydrodynamic performance of newly designed self-expandable graft stents under steady flow condition. Two graft stents with different coating materials and a bare TiNi metallic stent for comparison test were used in the experiment. Pressure variation and velocity distribution at the upstream and downstream of the stents were measured at flow rates of 5, 10, and 15 l/min, respectively. Pressure loss due to insertion of the stent increased with increasing flow rate exponentially as expected. At a flow rate of 15 l/min, pressure loss of Polyure-thane(PU)-coated graft stent was 6 times higher than that of TiNi metallic stent, while the pressure loss of a porous Polytetrafluoroethylene(PTFE)-coated graft stent was comparable to a bare TiNi metallic stent. Velocity profiles of the porous PTFE-coated graft stent were similar to those of a bare TiNi metallic stent regardless of flow rate. Furthermore, the velocity profile of PU-coated graft stent revealed an asymmetrical and relatively low central velocity at a higher flow rate than 10 1/min, expecially, where the effects resulted in increases of wall shear stress and normal stress. The worse hydrodynamic behavior of PU-coated graft stent than the other two stents might be attributed to formation of folds due to poor flexibility of coated material when inserting the graft stent into the pipe with a more smaller size, which later gave rise non-symmetry of flow area, increase of surface roughness and jet flow via the crevice between the stent and cylinder wall.