• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.193-194
• /
• 2014

원전은 고온기능시험 이후 2차계통 내부를 상대습도 40%이하로 관리하여 계통 재질 부식을 최소화하고 있다. 일반적으로 발전소에서는 운전 정지 후 상대습도 40%이하로 낮추는데 15일정도 소요되지만, 발전소 계통 중 일부 곡관부위는 약 60일정도 소요된다. 본 연구는 일부 계통 재료가 상대습도 제한치(<40%) 이상의 환경에서 장기간(최대 60일) 노출시 재료 건전성에 미치는 영향 평가이다. 평가를 위해 시편의 실험 전, 후 무게변화를 이용한 부식률 측정과 표면분석을 위해 광학현미경을 이용하였다. 사용 시편의 재료는 SA516 Gr.70이며 표면상태를 인위적으로 산화피막을 생성 시킨 것(2개)과 산화피막이 없는 것(6개)으로 2종류로 제작하였다. 총 시험기간은 60일이고 시험기간 중 산화피막이 없는 시편은 7일, 21일, 60일에 시편을 2개씩 꺼내어 무게를 측정하여 부식률을 계산하였다. 실험결과, 산화피막이 없는 시편은 노출되는 시간에 따라 부식률이 각각 0.35(7일), 0.21(21일), 0.67(60일) mpy이었고 산화피막이 있는 시편은 0.06(60일) mpy였다. 산화표면 분석결과, 산화피막이 없는 시편은 노출되는 시간에 관계없이 물방울이 맺힌 부분에 pitting을 확인하였다. 하지만, 산화피막이 있는 시편은 pitting의 흔적은 없었다. 산화피막이 없는 시편의 경우 시간에 따라 부식률은 높아지지만 학계에서 통용되는 뛰어난 내부식성 재료의 부식률 기준인 < 1 mpy이하기 때문에 재료 건전성에 미치는 영향은 거의 없을 것으로 판단된다. 또한, 대부분 원전의 경우 고온기능시험 또는 운전기간 동안에 2차계통 구성 재료 표면에 산화막이 생성되었기 때문에 산화피막이 있는 시편의 결과로 판단하면 상대습도 40%이상에 60일 이상 노출되어도 부식은 거의 일어나지 않았을 것으로 사료된다. 실증실험결과를 가지고 종합적으로 평가하면 상대습도 40%이상 환경에서 곡관부위가 60일이상 노출되어도 재료 건전성에 미치는 영향은 거의 없을 것으로 판단된다.

• International Journal of Highway Engineering
• /
• v.7 no.3 s.25
• /
• pp.23-30
• /
• 2005

Predicting distribution and variation of humidity inside concrete is essential to improve curing quality of concrete at field. The concrete humidity is predicted by numerical analysis using surface humidity as boundary condition. However, ambient humidity has been used instead of the surface humidity because the surface humidity could not be ccurately measured. Because it is hard to accurately measure the surface humidity, owever, the ambient humidity has been used instead of the surface humidity in the numerical analysis. In this paper, a methodology to accurately measure the surface humidity is suggested, and the ambient humidity and the humidity at the surface and inside the concrete measured by a series of laboratory tests are presented. The cause of low concrete humidity immediately after placement was investigated by a separately performed test. A surface humidity prediction model was developed using the measured humidity, and consequently validated through an additional test.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.10
• /
• pp.6445-6452
• /
• 2015

The surface of the cooling coil becomes dry, wet or partially wet depending on the operating condition. Thus, a proper design of the cooling coil should include a heat transfer analysis on dry, wet or partially wet surfaces. In this study, an elementary model, which analyzes the cooling on an elementaty basis, is proposed. Comparison of the predictions of the model with experimental data of the cooling coil revealed that heat transfer rates were predicted within 10.1%, airside pressure drop within 11.1% and sensible heat ratio within 5.7%. The model was used to investigate the effect of water circuitory on cooling coil performance.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.228-229
• /
• 2009

탐침현미경(Atomic Force Microscope)을 이용하여 탐침과 표면사이에 나노스케일의 접촉 반경을 가지는 접촉보를 만든 후 접촉 강성(contact stiffness) 을 관찰하였다. 다양한 습도 조건하에서 접촉 강성의 변화를 측정한 결과, 습도에 의해 접촉부의 인장 거동이 달라짐을 확인할 수 있었으며, 습도 변화에 따라 인장 거동의 천이점이 존재함을 확인할 수 있었다.

• Proceeding of EDISON Challenge
• /
• 2014.03a
• /
• pp.325-335
• /
• 2014

원자 힘 현미경 (Atomic Force Microscopy, AFM) 탐침과 표면 사이의 좁은 공간에서 형성되는 나노미터 크기의 메니스커스는 AFM으로 측정하는 표면 이미지에 영향을 주는 것으로 알려져 있다. 본 연구에서는 격자 기체 기반의 몬테카를로 방법을 이용하여 계의 상대습도 변화에 따른 시스템의 크기와 표면의 곡률이 메니스커스의 모양 및 이로 인해 발생하는 모세관 힘에 미치는 영향을 알아 보았다. 일반적으로 시스템의 크기가 작을수록, 표면의 곡률이 클수록 (표면이 거칠수록), 메니스커스 폭은 좁아지고 모세관 힘이 줄어드는 것을 확인 하였다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.11a
• /
• pp.168-168
• /
• 2012

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.45 no.5
• /
• pp.26-29
• /
• 2016

• Journal of Energy Engineering
• /
• v.16 no.1 s.49
• /
• pp.7-14
• /
• 2007

An experimental study is performed to investigate the effect of air-side heat transfer and friction on characteristics of finned tube heat exchanger under dry surface and wet surface conditions (RH 50%, 70%). Air enthalpy calorimeter is used to obtain the performance evaluation and analysis of a fined tube heat exchanger. Four finned tube heat exchangers with slit fin or plain fin are tested. The number of tube rows are 2 and 3, and the tube diameter is 7 mm. Air-side heat transfer and friction are presented in terms of j factor and friction factor. At dry surface condition, j factor decreases with increasing Re and j factor of 3 row is lower than that of 2 row. Also, the friction factor of a slit fin is larger than that of a plain fin. At wet surface condition, the heat transfer effect is more significant in the case of the slit fin than the plain fin and 2 row than 3 row. The j factor and friction factor are affected by humidity, tube row and fin configuration.

• The Korean Journal of Food And Nutrition
• /
• v.11 no.2
• /
• pp.221-227
• /
• 1998

This study was investigate correlation of moisture content, relative humidity, pH, color difference, myoglobin(Myo), oxymyoglobin(Oxy) and metmyoglobin(Met). The moisture content, relative humidity of loin and shank were not changed uniformly during storage, the pH was raised according to storage period. The L value was raised at the closing stage of the storage period, the surface of the b value was higher than interior. Between Myo and Met were positive correlation in common with loin and shank. The surface and interior of loin were negative correlation between Oxy and Met, the surface and interior shank were positive correlation between Myo and L value and were negative correlation between Myo and Oxy. The moisture content, relative humidity, pH and color was not correlation uniformly.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.12
• /
• pp.8165-8175
• /
• 2015

In Korea, summer is hot and humid, and air-conditioners consume lots of electricity. In such case, simultaneous usage of indirect evaporative cooler may reduce the sensible heat and save the electricity. In this study, heat transfer and pressure drop characteristics of indirect evaporative cooler made of aluminum, plastic, plastic/paper are investigated both under dry or wet condition. Results show that indirect evaporation efficiencies of the plastic/paper sample (38.5% ~ 51.4%) are approximately the same as those of the aluminum sample (41.9% ~ 47.5%), and are larger than those of the plastic sample (29.0% ~ 37.4%). This suggests that the plastic/paper sample could be a good substitute to the aluminum sample. However, the pressure drops across the paper channel are 92% ~ 106% larger than those across the aluminum channel. The heat transfer coefficients of the paper channel under dry condition are 15% ~ 44% larger than those of the plastic channel. The increases are 185% ~ 203% for the aluminum channel. The pressure drops of the paper channel are 34% ~ 48% larger than those of the plastic channel and 93% ~ 106% larger than those of the aluminum channel. Rigorous heat transfer analysis reveals that, for the plastic sample, 30% ~ 37% of the wet channels remain dry, whereas all the channels are wet for plastic/paper sample. For aluminum sample, the ratio is 17% ~ 23%.