• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.816-817
• /
• 2015

본 논문에서는 매입형 영구자석 전동기의 코깅토크 저감을 위해 회전자 표면에 노치를 적용하여 최적 설계를 수행하였다. 최적 설계를 위해 전역 최적점의 빠른 탐색이 가능한 크리깅 근사모델을 이용한 진화전략 알고리즘이 사용되었다. 설계 변수인 노치 크기에 대해 코깅 토크를 목적 함수로 두고 최적 설계를 진행하였으며, 이를 통해 찾은 전역 최적점과 지역 최적점 가운데 역기전력 특성을 고려하여 최종 설계안을 도출하였다.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.156-157
• /
• 2017

본 논문은 전차원 자속 관측기를 이용한 대용량 매입형 영구자석 동기전동기(IPMSM)의 센서리스 제어 기법을 제안한다. 기존의 전차원 자속 관측기를 사용한 제어 방식은 IPMSM의 자속 모델을 표면 부착형 영구자석 동기전동기(SPMSM)의 자속 모델처럼 해석하기 때문에 추정되는 회전각의 오차가 발생한다. 특히 릴럭턴스 토크가 큰 대용량 IPMSM 구동 시에는 회전각 오차가 크게 나타나므로 단위 전류당 발생하는 최대토크를 감소시켜 정밀한 MTPA 제어가 불가능하다. 제안하는 알고리즘은 전차원 자속 관측기를 통해 추정된 회전각의 오차를 보상하여 대용량 IPMSM의 정밀한 센서리스 제어를 가능하게 한다. 제안하는 기법의 타당성은 시뮬레이션을 통해 확인하였으며, 기존의 알고리즘과 비교하였다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.1
• /
• pp.24-31
• /
• 2011

In order to measure corrosion level of reinforcement rebar in RC structures, non-destructive test methods which are concrete surface current density method and infrared thermographic technique were employed to measure corrosion levels. Experimental test parameters were various levels of corrosion states(0, 1, 3, 5, 7% of weight loss) and concrete cover depth(30 mm, 40 mm) and two different reinforcing rebar arrangements. The larger amount of concrete surface current density, the higher corrosion level in reinforcement rebar. The laboratory conditions which are ambient temperature and humidity have negligible effect on the infrared thermographical data. After analysis of current density and temperature distribution from concrete surface, corrosion level of reinforcement rebar embedded in concrete can be measured qualitatively based on the amount of electric current and heat flux.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.732-733
• /
• 2015

본 논문에서는 외전형 영구자석 동기전동기(Outer rotor Permanent Magnet Synchronous Motor)의 회전자 형상에 따른 토크특성을 비교하였다. 표면부착형 영구자석(SPM) 형태의 FAN용 PMSM을 설계하고 이 모델을 기준으로 동일한 외경사이즈를 갖지만 더 높은 토크 밀도를 갖는 4가지 매입형 영구자석(IPM) 형태의 PMSM을 제시한다. Finite Element Analysis(FEM)을 통하여 각 모델의 특성을 해석하고 자석 사용량과 토크를 비교 및 분석하였다.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.27 no.3
• /
• pp.182-189
• /
• 2015

The Embedded Suction Anchor (ESA) is a type of permanent offshore foundation that is installed by a suction pile. To increase the loading capacity against pullout, three wings (vertical flanges) are attached along the circumference at 120 degrees apart. Analytical parametric study using the proposed analytical solution method has been conducted to identify the effects of several parameters that are thought to influence the behavior of ESAs. The analysis results show that the pullout capacity increases as the anchor depth and the soil strength increase, and decreases as the load inclination angle increases. The anchor having square projectional area and being pulled horizontally at the middle of its length provides the highest pullout capacity.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.2
• /
• pp.142-147
• /
• 2007

In order to measure corrosion level of steel reinforcement rebar which is inside reinforced concrete structure, infrared thermographic technique was employed. Experimental test parameters were four different ambient temperatures and various levels of corrosion states (0, 1, 3, 5, 7 and 10% of weight loss). After analysis of temperature distributions of concrete surface, the amount of heat flux from the concrete surface is directly proportional to the corrosion level which is inside of concrete.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.1
• /
• pp.78-83
• /
• 2010

This paper discusses the surface roughness of corroded reinforcement rebar in reinforced concrete structures focusing on the quantitative measurement technique for rebar corrosion. Reinforcement rebar was corroded using accelerated corrosion induced method and corrosion rates were 0%, 1%, 2%, 3%, 5%, and 10% of mass losses. Using 3-dimensional scanner each surface profile of reinforcement rebar was established, and surface roughness was measured. Through tests and analyses of corroded reinforcement rebar, the following topics were particularly discussed: measurement of surface roughness, relationship between area and surface roughness, relationship between surface roughness and bond performance. As a result, surface roughness of corroded rebar was found to be very effective to bond strength until 2% of corrosion rate. It was also discussed how to relate surface roughness of corroded rebar to bond strength of reinforced concrete structures.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.4
• /
• pp.126-132
• /
• 2018

As means to increase the use of concrete with recycled coarse aggregate (RCA), this study aims to evaluate the applicability for flexural strengthening of reinforced concrete beam with high-strength concretes and RCA on which FRP plates, used for repair and strengthening of old and low-durability reinforced concrete structures, is applied. In order to increase the adhesive force of epoxy and FRP plate, FRP plate was installed according to Near-Surface-Mounted (NSM) method. 12 specimens were manufactured using substitution rate of RCA (30%), concrete strengths (40MPa, 60MPa), diameters of deformed bar (D10, D13), and types of FRP plate (AFRP, CFRP) as variables to analyse flexural performance according to FRP plate and substitution rate of recycled aggregate. As a result, in all specimens, specimens strengthened by FRP plate showed a maximum of 17% increase in performance compared to specimens without FRP plate and strengthening performance of CFRP was found to be higher than AFRP. When modulus of rupture was used, the value of cracking moment was similar to that of the reference equation. As bending moment of some specimens strengthened by FRP plate failed to satisfy the criteria of KCI 2012 and ACI 440-2R, additional experiment is deemed as necessary.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.6
• /
• pp.287-291
• /
• 2006

Recently, various applications of permanent-magnet(PM) electric motor have been more increased. Compared with the other electric motors, PM electric motor has cogging torque which results from the interaction between PM of rotor and slot-teeth structure of stator. Audible noise and vibration is caused by this cogging torque. So, the reduction of cogging torque is main designing goal of PM electric motor. The purpose of this paper is to realize the decrease of cogging torque using new experimental design and response surface analysis which is one of the statistical methodologies.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.2
• /
• pp.80-87
• /
• 2008

A lot of conventional automotive components driven by mechanical power source are being replaced with electrical ones to comply with the demands of market and customer, therefore the amount of electric energy used in a vehicle will be increased continuously. The increment of electric power demand causes interest on new higher power system such as 42V Power Net, and furthermore necessity for development of energy storage device is highlighted recently. This paper present the design of the BLDC motor for electric air-conditioner in 42V system and compare with the characteristics of several type BLDC motor.