• Journal of Korea Foundry Society
• /
• v.44 no.1
• /
• pp.9-15
• /
• 2024

In this study, in order to improve the lifespan of parts made of manganese steel, manganese steel was cast by varying the amount of Ti added to the steel. In order to confirm the characteristics of the cast material, processing characteristics including tensile and surface characteristics and bearing ratio were investigated. It was confirmed that when the amount of Ti added to high manganese steel exceeds 0.5%, the strength of the alloy is improved due to grain refinement, and fine carbides are formed inside the steel. This results in increased resistance to surface wear compared to the alloy with only Mn added. There was no significant difference in the increase in tensile strength as the Ti content in manganese steel was increased. However, inclusion of Ti showed a small but greater effect on wear resistance compared to Mn, and the size and the distribution of carbides become coarse depending on the Ti content. and was evenly distributed. It was confirmed that the strength and surface properties of manganese steel can be improved by the addition of Ti to improve the lifespan of parts made with this steel. It was found that Ti is effective in developing materials with excellent wear resistance due to refinement of dendrite crystal grains. In the samples where Ti was added, the carbide appears to increase the resistance to surface roughness, and due to the nature of Mn steel, surface hardening begins to occur, which appears to extend the life.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.28 no.1
• /
• pp.146-153
• /
• 2001

The difference of composition of composite resin may affect the mechanical properties of composite resin and the environment is important for the properties of materials. The composite resin restoration is always exposed to fluid in oral cavity and the composite resin matrix is able to absorb water, which is accompanied by some swelling of the composite The uptake of water by composites has been correlated with decreases in surface hardness and wear resistance. The purpose of this study was to investigate the effects of water storage in $37^{\circ}C$ distilled water after 7days, 30days, 60days, 120days on compressive strength and flexural strength of dental composite resin, Z-100(group 1) Spectrum(group 2), Clearfil AP-X(group 3), Pyramid(group 4), Heliomolar(group 5). The compressive and flexural strength were measured by instron machine. The following results were obtained: 1. There were significant reduction of compressive strength as water storage time increased, 7days, 30days, 60 days, 120days(p<0.05). 2. There were significant reduction of flexural strength as water storage time increased, 7days, 30days, 60days, 120days(p<0.05). 3. Group 1, 2, 3 -hybrid type showed higher compressive and flexural strength than group 5-microfine type which had lower filler contents.

• Journal of the KSME
• /
• v.29 no.2
• /
• pp.118-124
• /
• 1989

피로파괴의 발생원인을 살펴보면 다음과 같이 4가지로 구별된다. (1) 설계불량 (2) 가공불량 (3) 소재불량 (4) 부적절한 사용 그러나 현재 기계설계시 일반적으로 형상계수 및 충격계수를 포함한 안전율을 여유있게 고려하기 때문에 피로강도가 간접적으로 설계시 반영되어 피로파괴는 주로 가공이나 원소재 불량 및 사용상의 부주의에 의한 경우가 대부분이다. 즉 기계가공 도중에 노치가 유입되어 응력집중을 발생시키거나, 규정된 표면처리 혹은 열처리가 이루어지지 못해서 재료의 피로강도가 저하한 경우가 많으며, 소재 역시 비금속 개재물이 다량 함유되어 있거나 열처리 특성이 조악한 소재가 사용되어 요구되는 강도를 확보하지 못한 경우도 많다. 그 반면 사용자 측에서도 설계강도를 무시한 과부하를 인가하거나, 부식환경 혹은 고온에서 사용하여 피로파괴를 촉진시키는 경우도 있으므로 사용자도 설계조건을 인식하여 그 한계를 넘지 않도록 해야 한다. 피로파괴는 단순한 원인에 의한 경우가 적고 복잡한 여러 형상이 중첩되는 경우가 많기 때문에 해석하기 어려운 경우가 많다. 결국 피로 파괴의 방지는 피로강도를 저하시킬 수 있는 요인들을 종합하여 설계단계에서부터 최종 사용단계까지 지속적인 관리에 의해서만 달성 될 수 있다.

• Proceedings of the Korean Society of Disaster Information Conference
• /
• 2016.11a
• /
• pp.349-352
• /
• 2016

기존의 가열식 일반아스팔트 공법은 동결 등에 원인으로 포장재의 수명이 짧아져 잦은 유지보수가 필요한 문제점을 갖고 있으며, 이로 인해 내구성이 뛰어난 포장공법의 필요성이 대두되고 있다. 불투수성 방수아스팔트는 이러한 문제를 해결하기 위한 방안의 하나로 아스팔트 혼합물이 골재와 골재 사이를 강력하게 부착하며, 골재간의 공간을 메우고, 골재표면을 두껍게 코팅하여 골재 상호간의 강한 접착을 유지시켜주는 열가소성 폴리머를 사용한 포장공법이다. 본 연구는 불투수성 방수아스팔트 혼합물 개발을 위한 연구의 일환으로 석회석함유량, 유제함유량, 다짐강도, 실험온도 차이에 따른 불투수성 방수아스팔트 혼합물의 압축강도 특성을 실험을 통해 비교 검토하였다. 결과 분석을 통해 각각의 변수에 따른 압축강도 특성을 파악하였으며, 불투수성 방수아스팔트 혼합물 배합설계에 기초자료로 활용하고자 한다.

• The korean journal of orthodontics
• /
• v.29 no.4 s.75
• /
• pp.445-456
• /
• 1999

As a result of increased education and communication, the field of orthodontics has recently been expanded to include a greater number of adult treatment procedures. With this increased demand for adult orthodontic treatment, a problem that frequently arises is the placement of appliances on teeth restored with porcelain. But conventional acid-etching is ineffective in the preparation of porcelain surface for mechanical retention of orthodontic attachments. Also, it is possible to damage on porcelain. The purpose of this study was to evaluate the effect of composite bonding materials and the porcelain surface treatment methods on shear bond strength, and to observe the porcelain fracture rates. To accomplish this purpose, this study was carried out with feldsphatic porcelain, Ceram II. Porcelain surface treatment methods were divided into intact glazed porcelain which had not treatment and surface roughening. Surface roughening by etching with Hydroluoric acid(HF), sandblasting with Microetcher II and compound treatment with etching and sandblasting. Bonding materials were Ortho-two and Transbond. All porcelain specimens were applicated with porcelain primer. 1. In comparision according to porcelain surface treatment, surface roughening groups by HF etching and sandblasting had higher shear bond than intact group. No significant difference was found in Transbond group. 2. Ortho-two group had the higher shear bond strength than that of Transbond group in B:.u etching and sandblasting. 3. E(Transbond. Intact)group had the lowest shear bond strength in all experimental group. The bond strength was higher than clinically successful bond strength. 4. Non-treated group had very higher porcelain rates than treated group. 5. This study indicates that porcelain surface-roughening may not be necessary to attachment of orthodontic brackets to porcelain surfaces.

• Journal of the Korea Concrete Institute
• /
• v.25 no.1
• /
• pp.3-9
• /
• 2013

In ultra high strength concrete, when electric arc furnace oxidizing slag is substituted for sea sand as fine aggregate, compressive strength was improved about 15 MPa. To figure out the cause of the improvement in compressive strength, this study considered the dissolution characteristics of Ca component in fine aggregate and examined the microstructure, porosity, microhardness, and Ca/Si mole ratio on the interface of fine aggregate and paste. And to examine the mechanism of strength improvement resulted from the shape of fine aggregate, this study measured the surface roughness of fine aggregate with AFM. According to the result of this experiment, the mechanisms of strength improvement in ultra high strength concrete resulted from the use of electric arc furnace oxidizing slag as fine aggregate can be divided into chemical and physical mechanisms. In the chemical mechanism, the soluble Ca component contained in electric arc furnace oxidizing slag is dissolved and forms a hydrate between fine aggregate and paste to improve the interlocking strength of fine aggregate-paste. Also, it makes the microstructure around the fine aggregate. And in the physical mechanism, electric arc furnace oxidizing slag has a twice greater surface roughness than sea sand, so the interlocking strength between fine aggregate and paste increases, which contributes to the development of compressive strength.

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.2
• /
• pp.357-364
• /
• 2001

This study deals with the effect on non-martensitic layer on the fatigue strength in carburized gear. The test gears are carburized, then treated by the combination of chemical polishing and electro-polishing. Carburization treatment is used widely on parts of power transmission system like surface hardened layer to improve fatigue strength. Carburized gears are observed using a scanning electron microscope(SEM) to determine the characteristics of crack initiation mechanism in the surface layer. The constant street amplitude fatigue test is performed by using and electro-hydraulic servo-controlled pulsating tester. The S-N curves are obtained and illustrated. The effect of non-martensitic layer on the fatigue strength is clarified.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.191-191
• /
• 2013

최근 차량 경량화와 승객의 안전성을 위하여 고성형/고강도강의 수요가 급격히 증가하고, 이를 위한 강종 개발로 고강도 및 고버링성 소재가 개발되고 있으며, 또한 차량의 자동차의 사용환경이 점차 가혹해지고 장수명화 됨에 따라 자동차 강판에서 방청방식의 중요성이 크게 대두되고 있어, 이를 충족시키기 위한 합금화융융아연도금 열연강판(HGA)의 사용이 증대되고 있다. 따라서 본 연구는 고강도/고버링성의 합금화용융도금열연강판 개발을 목적으로 하였으며, 합금 성분 및 PGL의 열처리 조건에 따른 기계적 물성 을 평가하였으며, SEM,OM등을 통한 미세조직 관찰 및 홀확장성 평가를 실시 하였다.

• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.213-216
• /
• 2004

본 연구에서는 복잡한 형상을 가진 음원으로부터 방사하는 음장을 등가음원법 (equivalent source method)을 이용하여 재구성한다. 일반적인 등가음원법의 기본 원리는 진동하는 물체의 표면 또는 내부에 등가음원을 분포시켜서 등가음원의 강도를 계산하는 방법이다. 각 등가음원의 강도는 음원의 경계 조건이나 측정된 음장 음압을 통해서 구할 수가 있으며 사용된 등가음원의 차수, 개수 그리고 위치 등은 고려되어야 할 중요한 변수들이다. 기존의 HELS (Helmholtz equation least square) 방법은 한 곳의 위치에 다양한 차수로 이루어진 등가음원을 사용하여 각 차수의 계수를 구하는 방법으로써 구형에 가까운 음원에 대해서 좋은 결과를 보이나 음장의 결과가 최대 차수의 선택에 따라서 큰 오차를 유발하는 문제점이 있다. 따라서 정규화 기법을 사용하여 음장을 재구성하기 위해 필요한 등가음원의 최적 차수를 구하고, 음원 내부에 최적 차수로 이루어진 등가음원을 여러 개의 점에 위치시켜서 재구성 정확도를 향상시켰다. 정규화된 등가음원법의 타당성 검증을 위하여 표면 일부가 진동하는 구에 대한 수치 해석 및 청소기 모델에 대한 음장 재구성 실험 을 수행하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.4
• /
• pp.79-87
• /
• 2004

The light pattern reflected from a machined surface contains some information like roughness and profile on the projected surface as expected in the Beckmann-Spizzichino model. In applying the theory into a real reliable measuring device, many parameters such as incident light power, wave length, spot size should be kept a constant optical value. However, the reflected light power is likely to change with the environmental noise, the variations of the light source, the reflectivity of the surface, etc. even though the incident light power is constant. In this study, a method for adjusting the incident light power to keep the reflected light power projected on a CMOS image sensor constant was proposed and a simple adjustment algorithm based on PI digital control was examined. Experiments verified that the proposed method made the surface roughness measurement better and more reliable even under variations of the height of light source.