• Polymer(Korea)
• /
• v.27 no.6
• /
• pp.576-582
• /
• 2003

When the halogenated flame retardant, decabromodiphenyl oxide, was added to the polypropylene/nylon blend, and was compounded with montmorillonite and compatibilizer, maleic anhydride polypropylene, the improvement of flame retardancy and mechanical properties was investigated. The degree of dispersion between polymer resin and inorganic nanoparticles was investigated, and the flame retardancy and mechanical properties was measured quantitatively. XRD results showed that the montrnorillonite was com-pletely exfoliated after polypropylen/nylon nanocomposites was mixed above twice. By compounding with montmorillonite, polypropylene/nylon blend system was overcome the deterioration of flame retardancy. The tensile strength and impact strength were slightly increased, and by compounding with montmorillonite, the additional increase in mechanical properties was obtained. Therefore, the flame retardancy of polypropylene / nylon blend was decreased by adding nylon, but by compounding with inorganic nanoparticle, improvement of the flame retardancy and mechanical properties was obtained.

• Polymer(Korea)
• /
• v.39 no.2
• /
• pp.311-316
• /
• 2015

Densely structured polyhedral oligomeric silsesquioxane (POSS) was employed as an additive to enhance hardness of silicon-based hybrid gels for LED encapsulants. To improve the miscibility of POSS and polysiloxane resin, alkyl or oligosiloxane branches were introduced to POSS moiety. Platinum-catalyzed hydrosilylation reactions were used to attach branches of 1-decanol, 9-decen-1-ol, and vinyl-terminated oligosiloxane to the POSS molecules. Alkyl-branched POSSs (decyl-POSS and decenyl-POSS) were immiscibile with polysiloxane resin and generated gels with low transparency and low hardness values. On the other hand, oligosiloxane-branched POSS (Siloxy-POSS) showed good miscibility with polysiloxane resin to give gels with high transparency. However, the prepared gels did not show noticeable improvement in hardness compared to the gels without the POSS additive.

• Polymer(Korea)
• /
• v.25 no.4
• /
• pp.528-535
• /
• 2001

Polyurethane specimens were mainly composed of polyol, MDI, silicone surfactant, and water. The effects of ethylene glycol on the cell size, forming magnification, cream time, gel time, take free time, final free rising height, and reactive temperature were investigated. The cyclopentane was used for PU foam as a physical blowing agent. The components were hand-mixed at about 5000 rpm within 4 seconds at room temperature. The mixtures with various ethylene glycol contents were foamed in the wood mold. When the index of isocyanate was fixed, as the amount of ethylene glycol increased, cell size and thermal conductivity were decreased by about 5.1% and 14%, respectively.

• Polymer(Korea)
• /
• v.38 no.2
• /
• pp.213-219
• /
• 2014

The rheological characteristics of highly concentrated polymer bonded explosive simulant were studied. Hydroxyl terminated polybutadiene (HTPB) and polyethylene plastomer (Exact) were used as binders. Sugar and Dechlorane particles whose physical properties are similar to research department explosive (RDX) were used as fillers. When HTPB was used, diethyl hexyl adipate (DEHA or DOA) was used as a plasticizer together for some cases. Highly concentrated suspensions were mixed in a batch melt mixer (Rheomixer 600, Haake) and rheological properties were measured by plate-plate and capillary rheometers. Wall slip phenomena, thixotropy with shear hysteresis, and flow instability were investigated as shear rate and amount of fillers changed.

• Polymer(Korea)
• /
• v.39 no.2
• /
• pp.281-286
• /
• 2015

UV-cured acrylic copolymer pressure sensitive adhesive (PSA) having different amounts of crosslinking agents were prepared and adhesion properties were investigated. 0.01 wt% of MMT clay was dispersed in 2-ethylhexyl acrylate (2-EHA)/acrylic acid (AA) monomer mixture containing 0, 0.05, 0.1 and 0.3 wt% 1,6-hexandiol diacrylate (HDDA) for crosslinking. It was investigated that the curing behavior and surface chemistry of PSAs were merely affected by the presence of MMT clays. On the other hand, adhesive properties were influenced by the MMT addition; a cohesive failure was restrained due to improved molecular elasticity even in uncrosslinked acrylic PSAs. However, it was also appeared that combination of 0.3 wt% crosslinking agent and MMT loading might result in the damage of adhesion properties of PSAs possibly due to the lack of chain flexibility. In our studies, it is suggested that the 2-EHA/AA PSAs incorporating 0.01 wt% of MMT and crosslinked with 0.05 wt% of HDDA exhibited the balanced adhesion properties without severe cohesive failure during strip.

• Polymer(Korea)
• /
• v.33 no.2
• /
• pp.153-157
• /
• 2009

The resin matrix in the dental composite is generally composed of 2,2-bis[4-(2-hydroxy-3-methacryloyloxy propoxy) phenyl] propane (Bis-GMA) as a base resin and triethylene glycol dimethacrylate (TEGDMA) as a diluent for the reduction of viscosity. The applications of dental composite were often limited in dentistry due to the relatively large amounts of volumetric shrinkage during polymerization and water uptake caused by the addition of TEGDMA to the resin matrix. In this study, in order to solve problems stemmed from the TEGDMA by reducing amount of diluent added to resin matrix, diethylene glycol dimethacrylate (DEGDMA) and ethylene glycol dimethacrylate (EGDMA) were explored as new diluents. A decrease in the volumetric shrinkage and an increase in the mechanical strength were observed by replacing TEGDMA in the dental composite to DEGDMA (or EGDMA). Reduction in the mechanical strength of the dental composite containing DEGDMA (or EGDMA), was not serious in comparison with that of the dental composite containing TEGDMA after water uptake.

• Journal of the Korea Concrete Institute
• /
• v.18 no.2 s.92
• /
• pp.227-232
• /
• 2006

This article presents the results of experimental study that investigates the effect of filler and shrinkage reducing agent influencing on the strength properties of MMA-modified polymer paste that was produced to develop the surface-repair and coating materials of the concrete structures. Results show that the flexural and compressive strengths of the polymer paste increased 29 and 27%, respectively, when the aluminum hydroxide completely replaced the calcium carbonate as the filler Furthermore, when the shrinkage reducing agent was used 30%, both strengths decreased about 29% comparing to when the agent was not used. As in the cases of flexural and compressive strengths, the adhesive strength increased as the content of aluminum hydroxide as the filler increased, and it decreased as the content of shrinkage reducing agent increased. The adhesive strength with a dry concrete substrate turned out to be $30{\sim}40%$ higher than that with a wet concrete substrate.

• Applied Chemistry for Engineering
• /
• v.23 no.2
• /
• pp.210-216
• /
• 2012

For the recycling of rapid-cooled steel slag, various specimens were prepared with the various replacement ratios of the rapid-cooled steel slag and the addition ratios of polymer binders. The physical properties of these specimens were then investigated by absorption test, compressive strength test, flexural strength test and hot water resistance test, and the pore and the micro-structure analysis was performed using scanning electron microscope. Results showed that the flexural strength increased with the increase of rapid-cooled steel slag and polymer binder, but the compressive strength showed a maximum strength at a certain proportion. By the hot water resistance test, compressive strength and flexural strength decreased remarkably and the total pore volume increased but the pore diameter decreased. SEM observation of the structure before the hot water resistance test revealed a very compact infusion of structure but the decomposition or thermal degradation appeared in polymer binders when observed after the hot water resistance test.

• Polymer(Korea)
• /
• v.25 no.5
• /
• pp.754-758
• /
• 2001

In order to use vesicle as a space of polymerization, monomer and cross-linking agent were put into hydrophobic part of vesicle. The vesicle solution of dimethyldioctadecylammonium bromide was formed by ultrasonication. Styrene and divinylbenzene were put into this solution and polymerization was conducted by adding AIBN. The polymer with sphere-shaped structure was obtained by removing all of the surfactant by extraction of ethanol And using methyl methacrylate and ethylene glycol dimethacrylate, this sphere-shaped polymer structure was also formed.

• Polymer(Korea)
• /
• v.38 no.3
• /
• pp.406-410
• /
• 2014

Zinc ion containing thiuram type accelerator zinc dibutyldithiocarbamate (ZDBC) was compared to other thiuram type accelerators (tetramethylthiuram disulfide (TMTD) and dipentamethylenethiuram tetrasulfide (DPTT)) in silica filled natural rubber (NR) compound upon vulcanization and mechanical properties (modulus, tensile strength, and elongation %). ZDBC added compound showed the fastest cure time (t10) and the highest reinforcement index (R.I.) among them and showed a marching behavior. The mechanism was reviewed and a new mechanism was proposed.